Dual Function Bowl Light Kit Owner’s Guide and Installation Manual Manual De Propietario English Español Form# 43550-01 20100610 ©2010 Hunter Fan Co.
Welcome Your new Hunter® light kit is an addition to your home or office that will provide comfort and performance for many years. This installation and operation manual gives you complete instructions for installing and operating your light kit. We are proud of our work. We appreciate the opportunity to supply you with the best products available anywhere in the world. Before installing your light kit, for your records and warranty assistance, record information from the carton and Hunter nameplate label.
Installation Methods of Hunter® Ceiling Fans Type A-Z Your ® light kit can be installed in one of four ways. The steps in this manual include instructions for all four installation methods: Installation directly on the ceiling, installation on fans with a removeable switch housing, fans with a non-removeable switch housing, and The Hunter Original. Preparing the Light Kit: Removable Switch Housing 1.
1 • Installing the Light Kit on the Ceiling 1. If you are replacing an existing light fixture, disconnect and remove the old #8-32 Screws fixture and mounting bracket. Leave the wires coming from the outlet box exposed. 2. Pre-install the two #8-32 screws, two corresponding washers, and two #8-32 nuts on the hanger bracket. Tighten nuts securely. Note: The hanger bracket should be positioned so that the two #8-32 screws are coming down and the green grounding screw is going up towards the ceiling. Nuts 3.
1 • Installing the Light Kit on the Ceiling (contintued) 9. Install the included CFL light bulbs into the lamp sockets. 10. Remove the lower chain extension from the light fixture by unhooking it from the breakaway connector. Leave the breakaway connector in place on the upper chain. 11. Thread the light pull chain through the hole in the center of the glass bowl. Place the glass bowl on the threaded rod until flush against the metal disc. 12.
2 • Installing the Light Kit on a Removable Switch Housing 1. Unscrew the three screws from the upper switch housing. Disconnect the 9-pin plug connectors. Remove the lower switch housing. 2. Push the plug button from inside the lower switch housing to remove the plug button and switch housing cap. NOTE: Save the plug button and switch housing cap should you choose to remove the light fixture in the future. 3.
2 • Installing the Light Kit on a Removable Switch Housing (Continued) 7. Remove the wire connectors from the two wires in the switch housing labeled “Connect Light Here” or “For Light Use.” To connect the wires, hold the bare metal leads together and place a wire connector over them, then twist the wire connector clockwise until tight. Connect the black wire with a white stripe from the switch housing to the black wire from the light kit.
3 • Installing the Light Kit on Fans With Non-Removable Switch Housing 1. Uninstall the two attachment screws from the switch housing cover. 2. Remove the plug or screw from the center of the switch housing cover. 3. Thread the switch housing cover onto the upper light housing. Align the screw holes in the upper light housing with the screw holes in the switch housing cover. Install the nut and washer onto the threaded rod from the light kit to secure the switch housing cover. 4.
3 • Installing the Light Kit on a Non-Removable Switch Housing (cont.) 8. Attach the light fixture to the switch housing with the two screws included with the light fixture, aligning the holes in the light fixture, switch housing cover, and switch housing. 9. Securely tighten the two screws. 10. Go to the instructions for Installing the Bulbs, Chains, and Globe.
4 • Installing the Light Kit on the Hunter Original 1. Uninstall the two screws from the switch housing plate. NOTE: Save the switch housing cap should you choose to remove the light fixture in the future. 2. Remove the wire connectors from the two wires in the switch housing labeled “Connect Light Here” or “For Light Use.” One wire is white and the other wire is black wire with a white stripe. Thread the two wires through the hole in the center of the light fixture. 3.
5 • Installing Bulbs, Chain, and Globe 1. First install included CFL medium base bulbs. 2. Thread the fan pull chain through the hole in the metal disc. Then, thread the fan pull chain through the hole in the center of the glass bowl. 3. Thread the light pull chain through the hole in the center of the glass bowl. 4. Place the cover plate up against the glass bowl. Align the holes in the cover plate and metal disc. 5. Thread the fan pull chain and light pull chain through the appropriate holes. 6.
6 • Troubleshooting Troubleshooting Light does not come on. 1. Make sure bulbs are installed properly. 2. Make sure breakers or fuses are on. 3. Verify that the light power lead is connected at the ceiling. Refer to your ceiling fan manual for locating assembly and wiring. Glass rattles. 1. Make sure the glass globe is secure. If you need parts or service assistance, please call 888‑830‑1326 or visit us at our Web site at http://www.hunterfan.com. Hunter Fan Company 7130 Goodlett Farms Pkwy.