www.HunterFan.com Table of Contents What to Expect with Your Installation Congratulations on purchasing your new Hunter® ceiling fan! It will provide comfort and performance in your home or office for many years. This installation and operation manual contains complete instructions for installing and operating your fan. Tools Needed 1.888.830.
www.HunterFan.com What to Expect with Your Installation Read and Save These Instructions If you are unfamiliar with wiring, use a qualified electrician. This product conforms to UL Standard 507. WARNINGS 30 inches from blade tip to nearest wall or obstruction Must be able to secure the fan to building structure or fan-rated outlet box Know your wiring Ceilings that are more than 34° will require an angled mounting kit. See page 3 for details.
Mounting Options Pliers OPTION 2 Flat Wire Strippers skip to next page 1. You will need a Longer Downrod sold separately 2.
www.HunterFan.com Mounting Options (continued) Support Structure Support Structure Ceiling Outlet Box (required) 8 Standard Mounting Style Ceiling Outlet Box (required) Use Standard or Low-Profile Mounting to hang the fan from a flat ceiling by a standard downrod (included). 12 Angled Mounting Style Use Angled Mounting to hang the fan from a vaulted or angled ceiling (see previous page). 4 M0001-01 • 08/03/12 • © Hunter Fan Company 1.888.830.
Ceiling Bracket Installation www.HunterFan.com 1.888.830.1326 For angled ceilings, point opening toward peak. er w o nP r Tu OFF Use wood screw Use machine screw (included) when securing (provided with outlet to support structure with box) when securing to approved electrical outlet existing ceiling fan-rated box. Drill 9/64” pilot holes outlet box. Make sure in support structure to aid it is securely installed in securing ceiling bracket and is acceptable for fan with hardware found in support of 31.
Ceiling Bracket Installation (continued) Preparation www.HunterFan.com 1.888.830.1326 ! KEEP DISC D AR Time Saver Tip: Get a helper Remove the shipping blocks from the motor. Save the five screws. They will be needed for blade iron installation. 6 M0001-01 • 08/03/12 • © Hunter Fan Company to insert grommets, found in the hardware bag, into the blades while you’re doing the next couple of steps.
www.HunterFan.com Option 1 Downrod 1.888.830.
www.HunterFan.com KEEP! (not to scale) 8” & 3/8” 1.888.830.1326 STRIP CUT Downrod (continued) ! KEEP Remove the pre-installed setscrew so that the downrod can be inserted. The wires can be cut, but leave at least 8” extending from the top of the downrod. Hand tighten the downrod (at least 4-5 full turns) until it stops. 8” Tighten the setscrew with pliers. DO NOT HAND TIGHTEN. 3/8” If the setscrew is not tightened securely, the fan may fall.
www.HunterFan.com Downrod (continued) Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan. DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. 9 M0001-01 • 08/03/12 • © Hunter Fan Company 1.888.830.
Wiring OM FR CEILIN www.HunterFan.com Note: To connect the wires, hold the bare metal leads together and place a wire connector over them, then twist clockwise until tight. G OM FR T KE Black FR (Ungrounded) M FA N Blue FRO (Ungrounded) AC Blue ING BR Black CEIL White M Using the orange wire connectors from the hardware bag, connect the black wire (ungrounded) from the ceiling to the black and the blue wires from the fan.
www.HunterFan.com Canopy Screw Holes Position the canopy so that, when lifted into place, the canopy fits into the hanging bracket as shown. Lift the canopy into place so that the screw holes are aligned. Insert the two canopy screws found in the hardware bag. Note: Fan style may vary. 11 M0001-01 • 08/03/12 • © Hunter Fan Company 1.888.830.
Blades www.HunterFan.com 1.888.830.1326 Remember the screws that you kept after removing the shipping blocks (page 6)? You need them plus five more from hardware bag for this step. Insert grommets found in the hardware bag into the holes in the blades, then secure each blade to a blade iron with screws found in the hardware bag. Lightly attach the blade irons to the motor with screws found in the hardware bag, then securely tighten after both screws are attached.
www.HunterFan.com Screw two (2) housing assembly screws from the hardware bag halfway into the motor housing. It does not matter which two screw holes you choose. Feed the wire plug through the center hole of the upper switch housing, then wrap keyhole slots around the screws and twist counterclockwise. the 1.888.830.1326 Insert the third screw, found in hardware bag, into place and then tighten all three (3) screws. Make sure the upper switch housing is securely attached to the mounting plate.
www.HunterFan.com Light Kit Switch Housing Screw Connect the plugs from the upper and lower switch housings. Make sure to line up the colored markings on the connectors. 1.888.830.1326 Notch Partially install two of the switch housing screws found in the bag. Align the notches in the sides of the lower switch housing with the screws on the upper switch housing. Twist the lower switch housing clockwise to lock into place. Install the third switch housing screw. Tighten all three screws securely.
www.HunterFan.com Light Kit (continued) 1.888.830.1326 Thumb Screw CONGRA YOU’RETULATIONS! DONE! Shade To install the shade, first loosen the thumb screws. Raise the shade to the light fixture. Tighten all thumbscrews securely. Install the bulbs into the sockets. When necessary, replace with bulbs of same wattage. Note: In compliance with US federal energy regulations, this ceiling fan contains a device that restricts its light output.
Maintenance & Cleaning www.HunterFan.com 1.888.830.1326 r we o nP r Tu ON Reverse Switch The fan pull chain controls the speed: high, medium, low, and off. The light pull chain controls the light fixture: on and off. To switch the direction of air flow, move the reverse switch to the opposite position. 16 M0001-01 • 08/03/12 • © Hunter Fan Company For cleaning the fan, use soft brushes or cloths to prevent scratching. Cleaning products may damage the finishes.
www.HunterFan.com Troubleshooting Fan doesn’t work Excessive wobbling Noisy Operation • Make sure power switch is on. • Tighten all of the blade and blade iron screws until they are snug. • Tighten the blade and blade iron screws until they are snug. • Pull the pull chain to make sure it is on. • Push the motor reversing switch firmly left or right to ensure that it is engaged. • Check the circuit breaker to ensure the power is turned on. • Make sure the blades spin freely.