www.HunterFan.com Table of Contents What to Expect with Your Installation 30 inches Hanging the Fan Wiring PA G E 8 Maintenance, Operation & Cleaning Light Kit M3504-01 • 02/08/17 • © 2012–2017 Hunter Fan Company 13 ? ? ? 14 PA G E 1 9 Troubleshooting PA G E PA G E PA G E 11 5 Blades Motor Housing 7 Switch Housing 10 4 PA G E 6 3 PA G E Ladder PA G E 2 PA G E 7 feet PA G E To register your fan please visit: www.HunterFan.
www.HunterFan.com What to Expect with Your Installation Read and Save These Instructions If you are unfamiliar with wiring, use a qualified electrician. This product conforms to UL Standard 507. WARNINGS 30 inches from blade tip to nearest wall or obstruction Must be able to secure the fan to building structure or fan-rated outlet box 7 feet from bottom edge of blade to the floor Know your wiring 1.888.830.1326 Assess location w.
www.HunterFan.com Tools Needed Escalera Taladro eléctrico (opcional) Destornilladores No deseche las bolsas con herrajes ni mezcle las partes de diferentes bolsas. Tome nota del símbolo impreso en cada bolsa con herrajes. Los símbolos pueden ser usados para identificar los herrajes apropiados para cada paso. Broca de 9/64” (opcional) Si se monta a una estructura de soporte, también necesitará estas herramientas. 3 M3504-01 • 02/08/17 • © 2012–2017 Hunter Fan Company 1.888.830.
www.HunterFan.com Ceiling Bracket 1.888.830.1326 Bumper er w o nP r Tu OFF Make sure all four bumpers are still attached. To avoid possible electrical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location. Use wood screws Use machine screws (included) when securing (provided with outlet to support structure with box) when securing to approved electrical outlet existing ceiling fan-rated box.
Ceiling Bracket (continued) Preparation www.HunterFan.com Time Saver Tip: Get a helper to insert grommets, found in the hardware bag, into the blades while you’re doing the next couple of steps. 5 M3504-01 • 02/08/17 • © 2012–2017 Hunter Fan Company 1.888.830.
www.HunterFan.com Hanging the Fan Locking Screw Screw Hole Screw Hole Ground Wire While holding the wires out of the way, lift the motor assembly and place the square hanger into the opening in the ceiling bracket. Be sure the ground wire attached to the hanger faces out of the large opening in the ceiling bracket. Once the motor is in the ceiling bracket, use the two locking screws, found in the hardware bag, to secure the motor to the ceiling bracket.
Wiring OM FR CEILIN www.HunterFan.com Note: To connect the wires, hold the bare metal leads together and place a wire connector over them, then twist clockwise until tight. G OM FR T KE Black FR (Ungrounded) M FA N Blue FRO (Ungrounded) AC Blue ING BR Black CEIL White M Using the orange wire connectors from the hardware bag, connect the black wire (ungrounded) from the ceiling to the black and the blue wires from the fan.
www.HunterFan.com Motor Housing Keyhole Rubber Plug Canopy Screw Keyhole Canopy Screw Place the fan housing over the motor. Align the keyholes in the fan housing with the two partially installed canopy screws in the hanger bracket. Rotate the fan housing to situate the screws in the end of the keyholes. The motor housing is not secured until the next step is complete. Do not leave unattended.
Blades www.HunterFan.com Insert grommets found in the hardware bag into the holes in the blades, then secure each blade to a blade iron with screws found in the hardware bag. Lightly attach the blade irons to the motor with screws found in the hardware bag, then securely tighten after both screws are attached. 9 M3504-01 • 02/08/17 • © 2012–2017 Hunter Fan Company 1.888.830.
www.HunterFan.com Switch Housing Screw two housing assembly screws from the hardware bag halfway into the motor housing. It does not matter which two screw holes you choose. Feed the wire plug through the center hole of the upper switch housing, then wrap keyhole slots around the screws and twist counterclockwise. 1.888.830.1326 Insert the third screw, found in the hardware bag, into place and then tighten all three screws. Make sure the upper switch housing is securely attached to the mounting plate.
www.HunterFan.com Light Kit 1.888.830.1326 Notch Switch Housing Screw Partially install two of the switch housing screws found in the bag. Connect the plugs from the upper and lower switch housings. Make sure to line up the colored markings on the connectors. Switch Housing Screw Align the notches in the sides of the lower switch housing with the upper switch housing screws. Lift the lower switch housing. Twist the lower switch housing clockwise to lock into place.
www.HunterFan.com Light Kit (continued) Metal Plate Light Pull Chain 1.888.830.1326 Fan Pull Chain Globe Globe Keeper Finial Cap CONGRA YOU’RETULATIONS! DONE! Finial Install a light bulb in each socket. Note: Globe style and number of lights may vary. Press the globe and globe keeper flush against the metal plate. Thread the light pull chain through the hole in the center of the finial cap and thread the fan pull chain through the hole in the side of the cap.
Maintenance, Operation & Cleaning r we o nP www.HunterFan.com 1.888.830.1326 Metal Plate r Tu ON Globe Globe Keeper Finial Cap Reverse Switch Finial Changing the bulbs - unscrew the finial and remove it from the threaded rod. Remove the finial cap and unscrew the globe keeper while supporting the globe with your other hand. Carefully remove the globe. Unscrew bulbs and replace with bulbs of same type and wattage. Reinstall the globe assembly.
www.HunterFan.com Troubleshooting Fan doesn’t work Excessive wobbling Noisy Operation • Make sure power switch is on. • Tighten all of the blade and blade iron screws until they are snug. • Tighten the blade and blade iron screws until they are snug. • Pull the pull chain to make sure it is on. • Push the motor reversing switch firmly left or right to ensure that it is engaged. • Use the provided balancing kit and instructions to balance the fan. • Check to see if any of the blades are cracked.