www.HunterFan.com Table of Contents Tools Needed Mounting Options Ceiling Bracket 30 inches To register your fan, please visit: www.HunterFan.com/register 4 Wiring Canopy Operation, Maintenance & Cleaning Light Kit Troubleshooting ? ? 14 PA G E 1 M3551-01 • 10/28/13 • © Hunter Fan Company 12 PA G E PA G E 10 8 ? 5 9 Blades PA G E 7 PA G E PA G E 6 Save your receipt for proof of purchase.
www.HunterFan.com What to Expect with Your Installation 1.888.830.1326 Read and Save These Instructions This product conforms to UL Standard 507. If you are unfamiliar with wiring, use a qualified electrician. WARNINGS w.1 - To reduce the risk of fire, electrical shock, or personal injury, mount fan directly from building structure and/or an outlet box marked acceptable for fan support of 70 lbs (31.8 kg) and use the mounting screws provided with the outlet box.
www.HunterFan.com Tools Needed Ladder Pliers Wire Strippers Screwdrivers If you are installing multiple remote-controlled fans on the same circuit breaker, you may need to perform a few extra steps to prevent interference or faulty operation of your remote controls. Power Drill (optional) Go to www.HunterFan.com/FAQs and click “How do I properly install multiple remotecontrolled fans?” for more information.
34O CEILING www.HunterFan.com Mounting Options OPTION 1 If you have a flat ceiling: 1. You will need a longer downrod (sold separately). 2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit (sold separately).
www.HunterFan.com Ceiling Bracket 1.888.830.1326 r we o nP r Tu OFF For angled ceilings, point opening toward peak. Use wood screws Use machine screws (included) when securing (provided with outlet to support structure with box) when securing to approved electrical outlet existing ceiling fan-rated box. Drill 9/64” pilot holes outlet box. Make sure in support structure to aid it is securely installed in securing ceiling bracket and is acceptable for fan with hardware found in support of 31.
www.HunterFan.com (not to scale) 8” & 3/8” STRIP CUT Downrod The wires can be cut, but leave at least 8” extending from the top of the downrod. Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan. DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. 8” 3/8” 6 M3551-01 • 10/28/13 • © Hunter Fan Company 1.888.830.
Wiring www.HunterFan.com Note: To connect the wires, hold the bare metal leads together and place a wire connector over them, then twist clockwise until tight. CEILIN G OM FR T KE black (live in) FR black (ungrounded) M FA N white (neutral in) FRO Using an orange wire connector from the hardware bag, connect the black wire (ungrounded) from the ceiling to the black wire from the receiver (marked “live in”).
www.HunterFan.com Canopy Screw Holes Position the canopy so that, when lifted into place, the canopy fits into the hanging bracket as shown. Lift the canopy into place so that the screw holes are aligned. Insert the two canopy screws found in the hardware bag. Note: Fan style may vary. 8 M3551-01 • 10/28/13 • © Hunter Fan Company 1.888.830.
Blades www.HunterFan.com Insert a blade into the motor housing. Your blades are shielded with Dust Armor® which is a nanotechnology coating that repels dust. For cleaning the fan, use soft brushes or cloths to prevent scratching. Cleaning agents may damage the finishes. Attach each blade to the fan using two blade grommets, found in the hardware bag, and two blade assembly screws, found in the hardware bag. 9 M3551-01 • 10/28/13 • © Hunter Fan Company 1.888.830.
www.HunterFan.com Light Kit 1.888.830.1326 Light Kit Assembly Screw Partially install two of the light kit assembly screws, found in the hardware bag. Align the keyholes in the light kit ring with the partially installed screws. Lift the light kit ring in place and rotate counterclockwise to situate the screws in the narrow ends of the keyholes. 10 M3551-01 • 10/28/13 • © Hunter Fan Company the Insert the third screw, found in hardware bag, into place and then tighten all three (3) screws.
www.HunterFan.com Light Kit (continued) 1.888.830.1326 Tab CONGRA Notch YOU’RETULATIONS! DONE! Bulb Install the included 18W CFL bulb. When necessary, replace with bulbs of same wattage. Position the notches in the outer rim of the globe so they line up with the tabs on the light kit ring. Carefully lift the globe up inside the light fixture as far as it will go. Rotate the globe in a clockwise direction until it is held tightly in place by the three tabs.
Operation, Maintenance, & Cleaning www.HunterFan.com Fan Off 1.888.830.1326 Medium Speed High Speed Switch Cover Plate Battery Door Low Speed Light Fan Off High Phillips Head Screw Removed Tabs To access the battery compartment, remove the small Phillips head screw that secures the battery door to the transmitter assembly. The battery should be installed with the positive (+) side up. Replace with a CR2032 battery when necessary.
Operation, Maintenance, & Cleaning (continued) www.HunterFan.com 1.888.830.1326 Safe-Exit The Safe-Exit Program gives you about thirty seconds of light when you turn the lights off to exit the room before the lights go out. To use Safe-Exit: Reverse Switch • Press the Fan Off button for at least three seconds to initiate the Safe-Exit Mode. • The lights will flash for visual confirmation. • The lights will stay on 50% brightness for 15 seconds and then begin to dim.
www.HunterFan.com Troubleshooting Fan doesn’t work Excessive wobbling • Make sure power switch is on. • Tighten all of the blade and blade iron screws until they are snug. • Push the motor reversing switch firmly left or right to ensure that it is engaged. • Check the circuit breaker to ensure the power is turned on. • Use the provided balancing kit and instructions to balance the fan. • Make sure the blades spin freely.
