www.HunterFan.com Table of Contents Tools Needed Preparation Ceiling Bracket 30 inches Hanging the Fan 3 4 Wiring 5 9 PA G E Ladder PA G E 2 PA G E 7 feet PA G E We are proud of our work and appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world. What to Expect with Your Installation PA G E Congratulations on purchasing your new Hunter® ceiling fan! It will provide comfort and performance in your home or office for many years.
www.HunterFan.com What to Expect with Your Installation Read and Save These Instructions If you are unfamiliar with wiring, use a qualified electrician. This product conforms to UL Standard 507. WARNINGS 30 inches from blade tip to nearest wall or obstruction Must be able to secure the fan to building structure or fan-rated outlet box 7 feet from bottom edge of blade to the floor Know your wiring 1.888.830.1326 Assess location w.
www.HunterFan.com Tools Needed Ladder Power Drill (optional) Screwdrivers 9/64” Drill Bit (optional) If mounting to a support structure, you will also need these tools. 3 M0047-01 • 11/26/12 • © Hunter Fan Company 1.888.830.
Ceiling Bracket www.HunterFan.com 1.888.830.1326 Bumper er w o nP r Tu OFF Make sure all four (4) bumpers are still attached. To avoid possible electrical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location. Use wood screws Use machine screws (included) when securing (provided with outlet to support structure with box) when securing to approved electrical outlet existing ceiling fan-rated box.
Ceiling Bracket (continued) Preparation www.HunterFan.com Time Saver Tip: Get a helper to insert grommets, found in the hardware bag, into the blades while you’re doing the next couple of steps. 5 M0047-01 • 11/26/12 • © Hunter Fan Company 1.888.830.
www.HunterFan.com Hanging the Fan Ground Wire Screw Hole While holding the wires out of the way, lift the motor assembly and place the square hanger into the opening in the ceiling bracket. Be sure the ground wire attached to the hanger faces out of the large opening in the ceiling bracket. Locking Screw Once the motor is in the ceiling bracket, use the two locking screws found in the hardware bag to secure the motor to the ceiling bracket. Note: Fan style may vary.
Wiring www.HunterFan.com O FR M CEILIN Note: To connect the wires, hold the bare metal leads together and place a wire connector over them, then twist clockwise until tight. G OM CEILING FR Green/Yellow Stripe Using orange wire connectors from the hardware bag, connect the black wire (ungrounded) from the ceiling to the black and the blue wires from the fan. Connect the white wire (grounded) from the ceiling to the white wire from the fan.
www.HunterFan.com Motor Housing Notch Motor Housing Screw Indentation Screw Holes Raise the motor housing up over the motor and ceiling bracket. Turn the motor housing so the screw holes align and the indentation in the housing locks into place with the notch in the ceiling bracket. The motor housing is not secured until the next step is complete. Do not leave unattended. With a Phillips head screwdriver, install the four motor housing screws found in the hardware bag.
Blades www.HunterFan.com Insert grommets found in the hardware bag into the holes in the blades, then secure each blade to a blade iron with screws found in the hardware bag. 1.888.830.1326 Lightly attach the blade irons to the motor with screws found in the hardware bag, then securely tighten after both screws are attached. Your blades are shielded with Dust Armor® which is a nanotechnology coating that repels dust. For cleaning the fan, use soft brushes or cloths to prevent scratching.
www.HunterFan.com Switch Housing Screw two (2) housing assembly screws from the hardware bag halfway into the motor housing. It does not matter which two screw holes you choose. Feed the wire plug through the center hole of the upper switch housing, then wrap keyhole slots around the screws and twist counterclockwise. the 1.888.830.1326 Insert the third screw, found in hardware bag, into place and then tighten all three (3) screws.
www.HunterFan.com Switch Housing 1.888.830.1326 er ow P n r Tu ON Partially install two of the switch housing screws found in the bag. Connect the plugs from the upper and lower switch housings. Make sure to line up the colored markings on the plug connectors. Align the notches in the sides of the lower switch housing with the screws on the upper switch housing. Twist the lower switch housing clockwise to lock into place. Install the third switch housing screw. Tighten all three screws securely.
Switch Housing (continued) www.HunterFan.com Maintenance, Operation & Cleaning 1.888.830.1326 Reverse Switch CONGRA YOU’RETULATIONS! DONE! The pull chain controls the fan: high, medium, low, and off. Changing the direction of air flow - move the reverse switch to the opposite position. 12 M0047-01 • 11/26/12 • © Hunter Fan Company Cleaning the fan - use soft brushes or cloths to prevent scratching. Cleaning products may damage the finishes.
www.HunterFan.com Troubleshooting Fan doesn’t work Excessive wobbling Noisy Operation • Make sure power switch is on. • Tighten all of the blade and blade iron screws until they are snug. • Tighten the blade and blade iron screws until they are snug. • Pull the pull chain to make sure it is on. • Push the motor reversing switch firmly left or right to ensure that it is engaged. • Check to see if any of the blades are cracked. If so, replace all of the blades.