www.HunterFan.com Table of Contents What to Expect with Your Installation Congratulations on purchasing your new Hunter® ceiling fan! It will provide comfort and performance in your home or office for many years. This installation and operation manual contains complete instructions for installing and operating your fan. Tools Needed Mounting Options 1.888.830.
www.HunterFan.com What to Expect with Your Installation 1.888.830.1326 Read and Save These Instructions This product conforms to UL Standard 507. If you are unfamiliar with wiring, use a qualified electrician. WARNINGS w.1 - To reduce the risk of fire, electrical shock, or personal injury, mount fan directly from building structure and/or an outlet box marked acceptable for fan support of 70 lbs (31.8 kg) and use the mounting screws provided with the outlet box.
www.HunterFan.com Tools Needed Ladder Pliers Wire Strippers 9/64” Drill Bit (optional) Power Drill (optional) If mounting to a support structure, you will also need these tools. 3 M3535-01 • 06/18/13 • © Hunter Fan Company Screwdrivers 1.888.830.
34O CEILING www.HunterFan.com Mounting Options OPTION 1 If you have a flat ceiling: 1. You will need a longer downrod (sold separately). 2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit (sold separately).
www.HunterFan.com Ceiling Bracket 1.888.830.1326 r we o nP r Tu OFF For angled ceilings, point opening toward peak. Use wood screws Use machine screws (included) when securing (provided with outlet to support structure with box) when securing to approved electrical outlet existing ceiling fan-rated box. Drill 9/64” pilot holes outlet box. Make sure in support structure to aid it is securely installed in securing ceiling bracket and is acceptable for fan with hardware found in support of 31.
www.HunterFan.com Assembling the Top Housing Upper Motor Cover Screw KEEP! ! KEEP Remove the pre-installed setscrew so that the downrod can be inserted. To assemble the housing to the hanger adapter, align the three raised tabs on the hanger adapter with the three narrow notches in the top housing. Make certain the housing sits flat on the adapter. Install three upper motor cover screws, found in the hardware bag, and tighten them securely. 6 M3535-01 • 06/18/13 • © Hunter Fan Company 1.888.830.
www.HunterFan.com Option 1 Downrod 1.888.830.
www.HunterFan.com (not to scale) & 3/8” 8” The wires can be cut, but leave at least 8” extending from the top of the downrod. Hand tighten the downrod (at least 4-5 full turns) until it stops. 1.888.830.1326 STRIP CUT Downrod (continued) 8” Tighten the setscrew with pliers. DO NOT HAND TIGHTEN. 3/8” If the setscrew is not tightened securely, the fan may fall.
www.HunterFan.com Downrod (continued) Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan. DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. 9 M3535-01 • 06/18/13 • © Hunter Fan Company 1.888.830.
Wiring www.HunterFan.com Note: To connect the wires, hold the bare metal leads together and place a wire connector over them, then twist clockwise until tight. CEILIN G OM FR T KE black (live in) FR black (ungrounded) M FA N white (neutral in) FRO Using an orange wire connector from the hardware bag, connect the black wire (ungrounded) from the ceiling to the black wire from the receiver (marked “live in”).
www.HunterFan.com Canopy Screw Holes Position the canopy so that, when lifted into place, the canopy fits into the hanging bracket as shown. Lift the canopy into place so that the screw holes are aligned. Insert the two canopy screws found in the hardware bag. Note: Fan style may vary. 11 M3535-01 • 06/18/13 • © Hunter Fan Company 1.888.830.
Blades www.HunterFan.com Holes Insert the blade into the slot. Align the holes on the blade with the holes in the fan motor. Your blades are shielded with Dust Armor® which is a nanotechnology coating that repels dust. For cleaning the fan, use soft brushes or cloths to prevent scratching. Cleaning agents may damage the finishes. Attach the blade to the motor using the flat washers from the hardware bag and blade assembly screws found in the hardware bag. Repeat for each blade.
Light Kit www.HunterFan.com 1.888.830.1326 Attachment Screw Partially install two attachment screws, found in the hardware bag, into the light kit mounting plate. Thread the 9-pin plug connector from the fan through the light kit. 13 M3535-01 • 06/18/13 • © Hunter Fan Company Align the keyholes in the light kit with the two partially installed screws and turn the light kit clockwise until the screws are in the narrow ends of the keyholes.
www.HunterFan.com Light Kit (continued) Attachment Screw Install the remaining attachment screw to secure the light kit to the mounting plate. Securely tighten all three screws. Connect the upper 9-pin plug connector from the fan to the lower 9-pin plug connector in the light kit. Make sure the light kit is securely attached to the mounting plate. Failure to properly secure all three assembly screws could result in the light fixture falling.
www.HunterFan.com Light Kit (continued) 1.888.830.1326 Globe Assembly Screw 4 Pin Plug CONGRA Glass Globe Connect the 4 pin plug from the ballast to the fluorescent bulb. Trim Ring Place the glass globe into the globe trim ring. Align the three holes in the trim ring with the three holes in the light kit. Install and securely tighten all three globe assembly screws, found in the hardware bag.
www.HunterFan.com Remote Control r Tu r we o nP ON Battery Door 1.888.830.1326 Fan Off High Phillips Head Screw To access the battery compartment, remove the small Phillips head screw that secures the battery door to the transmitter assembly. The battery should be installed with the positive (+) side up. Replace with a CR2032 battery when necessary. 16 M3535-01 • 06/18/13 • © Hunter Fan Company Note: The remote must be paired before the fan will operate.
Operation, Maintenance, & Cleaning www.HunterFan.com 1.888.830.1326 Medium Speed Fan Off High Speed Switch Cover Plate Low Speed Light Reverse Switch Removed Tabs To turn on fan, press a fan speed button. Speeds range from off (0) to high (3). Quickly press the Light button to turn the lights off and on. Hold the Light button to raise and dim the light level. Rocker- Style Plate To install the transmitter cradle, remove the two screws holding the switch cover plate. Do not remove the cover plate.
Operation, Maintenance, & Cleaning (continued) www.HunterFan.com Safe-Exit The Safe-Exit Program gives you about thirty seconds of light when you turn the lights off to exit the room before the lights go out. To use Safe-Exit: • Press the Fan Off button for at least three seconds to initiate the Safe-Exit Mode. • The lights will flash for visual confirmation. • The lights will stay on 50% brightness for 15 seconds and then begin to dim. After a total of 30 seconds, the lights will be completely off.
www.HunterFan.com Troubleshooting Fan doesn’t work Excessive wobbling • Make sure power switch is on. • Tighten all of the blade and blade iron screws until they are snug. • Push the motor reversing switch firmly left or right to ensure that it is engaged. • Check the circuit breaker to ensure the power is turned on. • Use the provided balancing kit and instructions to balance the fan. • Make sure the blades spin freely.