www.HunterFan.com Table of Contents Congratulations on purchasing your new Hunter® ceiling fan! It will provide comfort and performance in your home or office for many years. This installation and operation manual contains complete instructions for installing and operating your fan. What to Expect with Your Installation We are proud of our work and appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world.
www.HunterFan.com What to Expect with Your Installation Read and Save These Instructions If you are unfamiliar with wiring, use a qualified electrician. This product conforms to UL Standard 507. WARNINGS 30 inches from blade tip to nearest wall or obstruction Must be able to secure the fan to building structure or fan-rated outlet box Know your wiring Ceiling angles greater than 34° will require an Angled Mounting Kit. See page 4 for details.
www.HunterFan.com Tools Needed Ladder Pliers Wire Strippers 9/64” Drill Bit (optional) Power Drill (optional) If mounting to a support structure, you will also need these tools. 3 M0112-01 • 01/13/16 • © Hunter Fan Company Screwdrivers 1.888.830.
34O CEILING www.HunterFan.com Mounting Options OPTION 1 If you have a flat ceiling: 1. You will need a longer downrod (sold separately). 2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit (sold separately).
Ceiling Bracket r we o nP r Tu OFF For angled ceilings, point opening toward peak. Use wood screws Use machine screws (included) when securing (provided with outlet to support structure with box) when securing to approved electrical outlet existing ceiling fan-rated box. Drill 9/64” pilot holes outlet box. Make sure in support structure to aid it is securely installed in securing ceiling bracket and is acceptable for fan with hardware found in support of 31.8 kg (70 lbs) the hardware bag. or less.
www.HunterFan.com Top Housing & Blade Iron KEEP! ! KEEP Remove the pre-installed setscrew so that the downrod can be inserted. Lightly attach the blade irons to the motor with screws found in the hardware bag, then securely tighten after both screws are attached. 6 M0112-01 • 01/13/16 • © Hunter Fan Company Lower the top housing onto the top of the motor. Install the three top housing screws. 1.888.830.
www.HunterFan.com Option 1 Downrod 1.888.830.
www.HunterFan.com (not to scale) 8” & 3/8” The wires can be cut, but leave at least 8” extending from the top of the downrod. Hand tighten the downrod (at least 4-5 full turns) until it stops. 1.888.830.1326 STRIP CUT Downrod (continued) 8” Tighten the setscrew with pliers. DO NOT HAND TIGHTEN. 3/8” If the setscrew is not tightened securely, the fan may fall.
www.HunterFan.com Downrod (continued) Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan. DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. 9 M0112-01 • 01/13/16 • © Hunter Fan Company 1.888.830.
Wiring OM FR CEILIN Note: To connect the wires, hold the bare metal leads together and place a wire connector over them, then twist clockwise until tight. G OM FR CEILIN 1.888.830.1326 G (Ungrounded) (Grounded) (Grounding) OM FAN FR www.HunterFan.
www.HunterFan.com Canopy Screw Holes Position the canopy so that, when lifted into place, the canopy fits into the hanging bracket as shown. Lift the canopy into place so that the screw holes are aligned. Insert the two canopy screws found in the hardware bag. Note: Fan style may vary. 11 M0112-01 • 01/13/16 • © Hunter Fan Company 1.888.830.
Blades www.HunterFan.com Secure each blade to a blade iron as shown using the blade nuts, found in the hardware bag, and the blade assembly screws, found in the hardware bag. 12 M0112-01 • 01/13/16 • © Hunter Fan Company 1.888.830.
Switch Housing Screw two housing assembly screws from the hardware bag halfway into the motor housing. It does not matter which two screw holes you choose. www.HunterFan.com Feed the wire plug through the center hole of the upper switch housing, then wrap keyhole slots around the screws and twist counterclockwise. the 1.888.830.1326 Insert the third screw, found in hardware bag, into place and then tighten all three screws.
www.HunterFan.com Switch Housing (continued) Connect the plugs from the upper and lower switch housings. Make sure to line up the colored markings on the connectors. Lift the lower switch housing until its screw holes are aligned with the screw holes in the upper switch housing. Install the three switch housing screws, found in the hardware bag. Tighten all three screws. Note: Fan style may vary. 14 M0112-01 • 01/13/16 • © Hunter Fan Company 1.888.830.
Switch Housing (continued) Maintenance & Cleaning www.HunterFan.com 1.888.830.1326 er w o nP r Tu ON CONGRA T YOU’REUALTIONS! DONE! Reverse Switch Changing the direction of air flow - move the reverse switch to the opposite position. 15 M0112-01 • 01/13/16 • © Hunter Fan Company Cleaning the fan - use soft brushes or cloths to prevent scratching. Cleaning products may damage the finishes.
www.HunterFan.com Troubleshooting Fan doesn’t work Excessive wobbling Noisy Operation • Make sure power switch is on. • Tighten all of the blade and blade iron screws until they are snug. • Tighten the blade and blade iron screws until they are snug. • Pull the pull chain to make sure it is on. • Push the motor reversing switch firmly left or right to ensure that it is engaged. • Check the circuit breaker to ensure the power is turned on. • Make sure the blades spin freely.