Ashbury Bath Ventilator with Light English Owner’s Manual Model 81003 41937-01 20101026 ©2010 Hunter Fan Co.
W arning TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: Engineers (ASHRAE), and the local code authorities. 1. Use this unit only in a manner intended by the manufacturer. If you have questions, contact the manufacturer. 2. Before servicing or cleaning the unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally.
Check all the parts. If damaged, call 1-888-830-1326 for replacements. x4 E F G A *B H x2 I J 3/8” Cable Connector K *C x2 D L M Extra Screws relief cable * NOTE: Strain connector must be N installed. Not Included. O 95047-03-000 77481-01-000 03242-07-133 95261-02-000 74508-03-133 77522-01 65219 96397-01-214 for model 81001 96397-02-444 for model 81003 75184-01-133 86812-01-000 75733-01-214 for model 81001 75733-01-444 for model 81003 Included. Tools Needed. (Not supplied.
3 4 H E Remove the motor/blower from the housing. Remove packing material. 6 5 Remove the pre-loaded screw tip covers. Back out the pre-loaded screw tips until flush with the side of the housing. 7 8 F G Remove the wiring cover screw. Remove the wiring cover.
9 10 E C B Pop out the first wiring access slug. Use second if needed. Insert the strain relief (not included) into the housing and secure with washer. Choose Installation Option For New Construction - go to step A11, page 5 For Existing Construction - go to step B11, page 8 New Construction A12 A11 E 5/8 1/2 5/8 1/2 Position the correct depth mark at the bottom edge of the joist based on the thickness of your sheetrock. Screw pre-loaded screws into joist or framing.
A13 Route wires through the strain relief. For supply connection, use wires suitable for at least 90º C (194º F). A14 Ground Black Green 2 Pin A White Fan Motor 3 Pin Black Main Switch 1 (AC In) White White Light Bare Copper Black Light *Option Black Switch 2 (AC In) *Option Fan & Main Light Together Connect wires as shown. A16 0 A15 E G F Install the wiring cover plate. Make sure all wiring connections are inside the box or under the wiring cover plate.
A17 0 A18 0 H Reinstall the motor by inserting the tabs and pushing up into position. Make sure the wires are not pinched between the motor and the housing. Connect wiring harness. DO NOT ALLOW THE MOTOR TO HANG FROM THE WIRING HARNESS. A20 A19 I Secure the motor by tightening the 2 screws. Turn on the power source. A21 A22 ON Go to step C1 OFF on page 10 to attach grille. Test the motor. If the motor does not run, check the plug connection.
Existing Construction B11 B12 EXISTING FAN E Remove an existing fan and check to make sure the opening is large enough to accommodate the new motor housing (7 1/4”x 7 3/4”). Move the housing into position above the ceiling. B13 1 2 B14 Route wires through the strain relief. For supply connection, use wires suitable for at least 90º C (194º F). Attach existing ducting to duct connector. Tape joints. If ducting does not fit securely, an adapter may need to be purchased.
B16 Ground Black Green 2 Pin A White Fan Motor Bare Copper Black Main Switch 1 (AC In) White White 3 Pin Light Black Light *Option Black Switch 2 (AC In) *Option Fan & Main Light Together Connect wires as shown. B18 B17 F G H Install the wiring cover plate. Connect wiring harness. DO NOT ALLOW THE MOTOR TO HANG FROM THE WIRING HARNESS. B20 B19 I H Reinstall the motor by inserting the tabs and pushing up into position.
B22 B21 ON OFF Test the motor. If the motor does not run, check the plug connection. Turn on the power source. B23 Go to step C1 on page 10 to attach grille. Attaching the Grille C2 C1 L N M O Remove the thumbscrews. Remove glass dome.
C4 C3 K L Connect wiring harness. DO NOT ALLOW THE FIXTURE TO HANG FROM THE WIRING HARNESS. Remove the strain relief bracket screw. C5 C6 J Insert the strain relief bracket’s dog-leg tab so that it hooks over the lip of the motor. Reinstall the strain relief bracket screw. Position the strain relief bracket under the motor as shown. C8 C7 L L M Align posts 1, 2, and 3 (stamped into motor housing) with posts 1, 2, and 3 (stamped into light fixture). Slide light fixture over posts.
C10 C9 N Align glass dome and push up. Install 2 Max 60 Watt A15 bulbs (Not Included). C11 O Screw glass dome into position.
Trouble Shooting Problem: Fan does not come on. Solution: • Hunter Fan Bath Ventilators are extremely quiet. To confirm that the fan is running, place your hand near the vents to feel the air movement. • Turn power on, replace fuse, or reset breaker. • Check all plug connections to be sure they are secure. • Check the wiring to make sure it matches the wiring diagram. Problem: Light does not come on. Solution: • Replace the light bulb with a new bulb. • Turn power on, replace fuse, or reset breaker.
Warranty Hunter Fan Company Bath Exhaust Fan LIMITED WARRANTY Hunter Fan Company makes the following limited warranty to the original user or consumer purchaser of this Hunter bath exhaust fan: If any part of your Hunter bath exhaust fan (except for glass fixtures and light bulbs) fails at any time within one year after the date of sale to you due to a defect in material or workmanship, we will repair or, at our option, replace the defective part free of charge for parts and labor performed at our nearest s