+ + + HH SERIES MANUAL Product Contents + + HH Series 2 4PJ12235-HH series_V.01.
Hurom Juicer Manual For Household Use (Warranty Included) 1 Read “Precautions for safe use (Page 4)” carefully and use the appliance properly. 2 Save the manual and keep it in a convenient location for future reference. 3 Check if the voltage indicated on the base of the appliance corresponds to the local voltage before you connect the appliance. 4 Any quality improvements are subject to change without notice.
With Hurom’s own Slow Squeezing System and the all-new juice cap mixing function, you can easily make your own personalized juice filled with rich flavor and nutrients. 1. More Nutrients and Flavor: Your own personalized juice Various mixed juices Make an easy, simple juice with a single type of fruit or a mixed juice that is custom-fit to your taste and health needs by combining various ingredients together. With versatility of juice cap mixing function, you can be your own juice mixologist.
GENERAL DESCRIPTION AND PARTS NAMES HOPPER PULP CONTAINER AUGER JUICE CONTAINER STRAINER CLEANING BRUSH SPINNING BRUSH SMALL CLEANING BRUSH CHAMBER PUSHER BASE 02 l 2 4PJ12235-HH series_V.01.
SPECIFIC TERMS FOR PARTS 1.Hopper front arrow 3.Hopper rear arrow 4.Base arrow 5.Chamber arrow 6.Grip 2.Pulp outlet 7.Operating switch 8. Juice outlet 9.Juice cap 10.Power cord NUMBER OF ATTACHMENT 1 Pusher, 1 Hopper, 1 Auger, 1 Stainer, 1 Spinning brush, 1 Chamber, 1 Base, 1 Juice container, 1 Pulp container, 1 Small cleaning brush, 1 Cleaning brush, 1 Manual www.hurom.com I 03 2 4PJ12235-HH series_V.01.
PRECAUTIONS FOR SAFE USE All users of this appliance must read and understand this safety precaution before operating. WARNING Hazards or unsafe practices which could result in serious personal injury or death. CAUTION Hazards or unsafe practices which could result in minor personal injury or appliance damage. This sign indicates contents that may cause risk of a fire or an electrical shock. Specific warnings are written in the sign.
WARNINGS AND CAUTIONS PLUG THE POWER CORD CORRECTLY AND PUSH IT TIGHT IN A WALL SOCKET. It may cause an electric shock or a fire. IF THE SUPPLY CORD IS DAMAGED, IT MUST BE REPLACED BY THE MANUFACTURER ITS SERVICE OR SIMILARLY QUALIFIED PERSONS IN ORDER TO AVOID A HAZARD. If the power cord is damaged, it may cause electric shock or fire. NEVER ALTER THE APPLIANCE. ALSO, DO NOT DISASSEMBLE OR REPAIR BY YOURSELF.
WARNINGS AND CAUTIONS CAUTION Hazards or unsafe practices which could result in minor personal injury or appliance damage. WHEN PLACING INGREDIENTS INTO THE HOPPER CHUTE, ONLY USE THE PUSHER PROVIDED. It may cause injury or failure. DO NOT OPERATE WITHOUT LOCKING THE HOPPER PROPERLY. It may cause an injury or a failure. ALWAYS UNPLUG THE APPLIANCE AFTER USE. ALWAYS DISCONNECT THE APPLIANCE FROM THE SUPPLY IF IT IS LEFT UNATTENDED AND BEFORE ASSEMBLING, DISASSEMBLING OR CLEANING.
WARNINGS AND CAUTIONS DURING THE OPERATION, DO NOT ATTEMPT TO MOVE THE BASE, DISASSEMBLE THE CHAMBER SET OR PARTS AND TRY TO LOCK THEM. It may cause an injury or a failure. Any act of event needed, switch off first and unplug the power cord. PLACE THE APPLIANCE ON A FLAT AND STABLE SURFACE. It may cause injury or failure. WHEN DETECTING A GAS LEAK, DO NOT INSERT THE POWER CORD INTO ITS SLOT. OPEN THE WINDOW TO VENTILATE FULLY AND IMMEDIATELY. It may cause injury or failure.
SLOW JUICER ASSEMBLY STEP 4 Align the chamber arrow [ ] with hopper arrow [ OPEN] and turn the hopper clockwise until it clicks so that the hopper arrow [ CLOSE] aligned with chamber arrow[ ]. OPEN STEP STEP 3 2 Make sure to press the auger down into the strainer in STEP 2. The hopper does not close properly when the auger does not fit in completely. Assemble the parts in the following order: Chamber>Spinning Brush> Strainer. Make sure chamber arrow [ ] aligns with strainer arrow [ ].
SLOW JUICER ASSEMBLY IN DETAIL 4 Align the hopper arrow with the base arrow located at the rear of the appliance. The hopper will not close if the parts are assembled incorrectly. Hopper rear arrow the parts in the order of chamber> spinning brush> strainer> auger> hopper (or assemble the spinning brush into the chamber then fit 2,3 Assemble strainer ridge in the chamber inner groove). Make sure all the arrows of chamber [ ], strainer [ ] and hopper [ OPEN ] are aligned in a vertical line.
HOW TO USE THE APPLIANCE REAR VIEW 2 Wash the fruits and/or vegetables and cut them into small pieces that can fit into the hopper chute. Place the suitable pieces into hopper chute slowly and press with a pusher. Use fresh fruits and vegetable for juicing as they contain more juice themselves. 1 OPERATING SWITCHES 작동스위치 Normal direction 정회전 Normal 정회전 direction Press 누름 OPERATING 작동스위치 SWITCHES off(정지) off (stop) 역회전 Reverse direction 역회전 Reverse direction Press [On] button to start.
JUICE CAP AND EXTRACTION SEAL JUICE CAP This is the juice outlet cap on the chamber. Close the juice cap to fill up the chamber with juice from various ingredients. Juice cap 1 2 Juice cap 3 Close juice cap and press [ON] button to start. When juice starts filling up the chamber, you can mix banana, nuts, boiled sweet potato, etc. and liquids such as milk as well as vegetables and fruits for a unique smoothie.
WHEN THE AUGER IS STOPPED DURING OPERATION (REVERSE/REV BUTTON) 1 Click the [Reverse/REV] button on the operating switch and stop the appliance. Stop 2 Press the [Reverse/REV] on the operating switch for 3~5 seconds and release it. Repeat this process 2~3 times. Reverse button pushes the ingredients back up. Reverse only works while the button held down. The Reverse rotation of the auger stops once the button is released.
IMPORTANT SAFEGUARDS FOR USE ∙ Fruits with pits and hard seeds such as nectarines, peaches, mangos, apricots, plums and cherries must be pitted before juicing. ∙ Cut fibrous ingredients (water parsleys, etc) into small sizes about 3~4cm(1.5inch) before placing into the hopper chute. ∙ Drink the fruit juice or green vegetable juice immediately after extraction. The juice will lose taste and nutritional value longer it is exposed to air.
DISASSEMBLING, CLEANING AND CARE FIGURE IN ORDER 1 3 2 Juice outlet 14 l 2 4PJ12235-HH series_V.01.
DISASSEMBLING, CLEANING AND CARE 4 5 1. Ensure the motor has stopped completely and unplug the power cord. When unplugging the power cord, hold the head part of the power cord and unplug it. Do not touch the power cord with wet hands. 2. Hold the juice outlet and the hopper with both hands and lift them up from the base. 3. Disassemble to parts as below: 1) Unlock the chamber by rotating it counterclockwise. 2) Remove the auger. 3) Remove the strainer. 4) Remove the spinning brush. 4.
DISASSEMBLING AND CLEANING THE CHAMBER juice cap seal chamber seal 1 Remove the juice cap seal and the chamber seal. Open juice cap first. Hold the chamber and juice cap with one hand and peel off the juice cap seal with the other hand. Remove the chamber seal by pinching and twisting it off with two fingers. Extraction Seal the extraction seal at the bottom of 2 Open the chamber. 3 Wash the chamber and all the seals. Wash chamber and chamber seal with cleaning brush under the running water.
STERILIZATION AND EASY CLEANING SYSTEM STERILIZATION For sterilization, use baking soda or natural cleaning liquids only. Sterilize all washable parts by immersing in a dilute solution of baking soda (about 1~2 teaspoon in 1 quart of water) for 30 minutes. EASY CLEANING SYSTEM After about 15 seconds, turn off the appli- closing the juice cap, pour water into the open the juice cap and discharge the 1 After 2 ance, hopper chute and press the [ON] button. water.
DISASSEMBLING AND CLEANING THE SPINNING BRUSH 1 Spinning brush Silicone brush 2 3 Remove the spinning brush from strainer. Detach the silicone brush from the spinning brush. As shown in the figure, hold the outer part of silicone brush and pull it out gently in the direction of the arrow. Silicone brush may be torn or damaged if it is pulled apart forcefully. With the cleaning brush, wash inside and outside of spinning brush under running water.
ASSEMBLING THE SPINNING BRUSH SPINNING BRUSH SILICONE BRUSH 1 Inner wing 1 Top (longer part) 2 Outer wing Brush groove Check the groove of the spinning brush and the direction of silicone brush. There are grooves to insert silicone brush in the spinning brush. Silicone brush has inner wing 1 and outer wing 2. As shown in the figure on left, position the silicone brush so the ‘inner wing’ faces the spinning brush.
ASSEMBLING THE CHAMBER SEAL 1 Hold the chamber seal by pinching it between the thumb and index finger. 2 Insert the chamber seal into the chamber hole. As shown to the left in the dotted circle, let the protruding part on the chamber seal face upward when you hold it by pinching it between the thumb and index finger. Chamber seal 3 Insert the bottom of the chamber seal into the chamber hole and press it down fully. Do not insert the entire chamber seal.
ASSEMBLING THE JUICE CAP SEAL 1 Hold juice cap seal as shown on the left. 2 Open the juice cap and fit the juice cap seal on to the inner disk. 3 Arrange the seal for a complete fit. As shown on the left in the dotted circle, the opening on the seal must be visible when you hold the seal. Juice cap seal Be careful not to drop the chamber. If the seal is not placed correctly, it may cause juice leakage. www.hurom.com l 21 2 4PJ12235-HH series_V.01.
TROUBLESHOOTING Please check the details below before contacting Technical Support for repair or service. If you need additional information, please contact the local Customer Care Center or visit www.hurom.com. When applying for after-sales service, please have the manufacturer’s serial number or bar code available. THE APPLIANCE DOES NOT WORK. Make sure the power cord is properly plugged in. Check if the hopper is assembled properly.
SPECIFICATIONS APPLIANCE STANDARDS PRODUCT NAME Hurom Slow Juicer MODEL NAME HH Series RATED VOLTAGE 230-240 V RATED FREQUENCY 50 Hz RATED POWER CONSUMPTION 150 W RPM (REVOLUTIONS PER MINUTE) 70 rpm CORD LENGTH 1.4 m이상 MOTOR Single-phase induction motor FUSE 250 V 5 A WEIGHT 6.1 kg (13.4 lb) OUTWARD DIMENSIONS Width 167 mm Length 237 mm Height 398 mm RATED OPERATING HOUR Less than 30 minutes www.hurom.com l 23 2 4PJ12235-HH series_V.01.
WARRANTY Product name Model name Manufacture’s serial number Date of purchase Supplier Customer name Address Important: To better protect your purchase, fill out and mail this form to a local distributor where you purchased the appliance and keep the original receipt. This certifies that the Hurom Slow juicer is covered under warranty by construction and workmanship.
MEMO www.hurom.com l 25 2 4PJ12235-HH series_V.01.
2 4PJ12235_V.01 www. hurom.com 2 4PJ12235-HH series_V.01.