Instructions / Assembly

ManualsBrandsHusky ManualsCeiling Mounted RacksOverhead Ceiling Mount Storage Rack

THANK YOU FOR YOUR PURCHASE

Adjustable Ceiling Storage Rack

Model # ACR4896B

WARNING: Excessive weight hazard! Use two or more people to move and install this rack to avoid injury.

Do not leave children unaended near overhead rack. High risk of injury if installed incorrectly. Follow instrucons

carefully and rounely inspect your system to ensure all components are fastened securely. DO NOT JUMP, CLIMB

OR HANG FROM THIS CEILING RACK. Never install more than one of these ceiling storage rack units on any two

overhead joist supports. Use care when working with metal parts, wear gloves. Do not use this unit for anything other

than the manufacture’s intended purpose.

600 lbs.

This unit has a total load capacity of 600 pounds of evenly

distributed weight (not to exceed 18.75 lbs. per square foot), using

all 8 lag bolts (included in package) anchored into solid wood

joists or supports capable of supporng such a load. Do not over

load. Do not aempt to mount to steel beams. Be sure overhead

joists and supports are structurally sound. Edsal is not liable for

structure failure, or damage or injury resulng from structure

failure.

Warranty

Important Safety Informaon

USE AND CARE GUIDE

Quesons, problems, missing parts?

Contact our customer service department for assistance:

7 a.m. - 5 p.m., CST, Monday-Friday:

Chat: www.edsal.com/chat or www.edsal.com/contact

Email: support@edsal.com

Phone: 1-773-475-3131

Edsal Manufacturing Company, Inc. products are guaranteed for a period of one (1) year from the date of purchase. The SOLE AND EXCLUSIVE REMEDY for

such defects is the repair or replacement of a defecve product or parts thereof by Edsal Manufacturing Company, Inc. or, at Edsal Manufacturing Company,

Inc opon, refund of the purchase price upon return of the item to Edsal Manufacturing Company, Inc.. This warranty shall not apply in the event the

products are damaged as a result of misuse, neglect, accident, moisture, improper applicaon, improper assembly, or assembly not in conformity with the

instrucons of Edsal Manufacturing Company, Inc., failure to abide by safety precauons prescribed by Edsal Manufacturing Company, Inc or modicaon

or repair by persons not authorized by Edsal Manufacturing Company, Inc..

To obtain replacement parts please provide: Model Number, Part Number & Descripon, Store Locaon and Date Purchased

Summary of content (10 pages)

PAGE 1
Adjustable Ceiling Storage Rack Model # ACR4896B USE AND CARE GUIDE Questions, problems, missing parts? Contact our customer service department for assistance: 7 a.m. - 5 p.m., CST, Monday-Friday: Chat: www.edsal.com/chat or www.edsal.com/contact Email: support@edsal.
PAGE 2
Parts List D x2 Side Brace #GLSB-48-B E x2 Left Beam #GLBML-B A x4 B x4 C x4 F x2 Ceiling Angle Bracket Upper Post Lower Post #GLUP-B #GLLR-B Right Beam #GLSA-B G x1 H x6 Center Support Cross Support #GLFTB-48-B #GLSTB-R-48-B #GLBMR-B I x2 End Wire Deck #GLWFDS-48 K x8 L x36 M x36 N x72 O x8 Lag Bolt Hex Bolt Lock Nut Small Washer Large Washer J x2 Center Wire Deck #GLWFD-48 Tools Required Magnetic Leveler Safety Glasses Pencil Tape Measure Stud Finder 7/32” Drill Bit 7/1
PAGE 3
Assembly Instructions Step 1 - Plan the Installation Determine if your ceiling rack will be installed parallel or perpendicular to the direction of your ceiling joists. Use a stud finder to locate the joists if ceiling is finished with drywall. Check the spacing of your ceiling joists to ensure that they will work for the size and direction of your ceiling rack install. If the spacing of your joists is 24” there should be ceiling joists located in the necessary position.
PAGE 4
Assembly Instructions Step 2 - Install Ceiling Brackets (A) Locate and mark the center of ceiling joist with a pencil. Use a stud finder to locate the joists if ceiling is finished with drywall. Use Ceiling Angle Bracket as a template to mark the two end holes of the Ceiling Angle Bracket on the center line of the joist using a pencil. Drill pilot holes using a 7/32” drill bit to the marked locations.
PAGE 5
Assembly Instructions Step 3 - Assemble Upper and Lower Posts (B & C) Determine desired height of ceiling rack from the ceiling to bottom of the overhead rack. Join the upper and lower post and line up the holes to the determined height. Bolt Upper Post (B) to Lower Post (C) using two Hex Bolts (L), two Lock Nuts (M) and four Small Washers (N). Bolt at the top hole location of the lower post and at the bottom hole location of the upper post where they overlap. Each bolt assembly should be on opposite holes.
PAGE 6
Assembly Instructions Step 4 - Install Post Assemblies Continued For Perpendicular Assembly: Bolt together one post assembly through the hole located on the side of the post to the center hole of the inside angle of bracket using one Hex Bolt (L), one Lock Nut (M) and two Small Washers (N). The backside of the post must be facing in and the tapered ends of the post slots must be facing down.
PAGE 7
Assembly Instructions Step 6 - Assemble Left and Right Beams (E & F) Bolt together one Left Beam (E) and one Right Beam (F) at the determined 72” or 96” length assembly by using four Hex Bolts (L), four Lock Nuts (M) and eight Small Washers (N). Repeat steps to assemble the other Left and Right Beam. 72” Assembly E E ✓ F F 96” Assembly E E F F ✓ Step 7 - Install Beam Assemblies Install one beam assembly by attaching both ends of the beam into the bottom slots of each post.
PAGE 8
Assembly Instructions Step 8 - Install Center Support (G) Bolt the Center Support (G) into the two holes found in the middle of each beam assembly (see diagrams for reference to hole location on a 72” or 96” beam assembly). Use two Hex Bolts (L), two Lock Nuts (M) and four Small Washers (N) per side.
PAGE 9
Assembly Instructions Step 9 - Install Cross Supports (H) Assemble the six Cross Supports (H) by placing the rivets located on both ends of the cross support into the triangular holes located on the top ledge of the both beam assemblies. H ✓ H Step 10 - Install Wire Decking (I & J) Place the End Wire Decks (I) on the ends of the beams with the notched corners facing the end corners of the posts. The notched corners should provide clearance for the posts.
PAGE 10
Assembly Instructions STEP 11 - Final Inspection Check each beam and post connection to be sure that the beams are properly seated and brackets are firmly connected to the overhead joists. Make sure all bolts and nuts are properly tightened. It is recommended to periodically repeat this inspection process to ensure safety. ✓ Retain this manual for future use.