Use and Care Manual

0706
AIR SUPPLY AND CONNECTIONS
The connector on the tool must not hold
pressure when air supply is disconnected.
Do not use any type of reactive gases,
including, but not limited to, oxygen and
combustible gases, as a power source.
Use only a pressure-regulated compressed
air source to limit the air pressure supplied to
the tool.
If
an incorrect fitting is used, the tool can remain
charged with air after disconnecting and thus will
be able to drive a fastener even after the air line
is disconnected, possibly causing injury.
Use
filtered, lubricated, regulated compressed air
only. Use of a reactive gas instead of
compressed air may cause the tool to explode
which will cause death or serious personal injury.
The regulated pressure must not
exceed 100psi. If the regulator fails, the pressure
delivered to the tool must not exceed 200psi.
◆Before unloading or making adjustments.
◆When maintaining the tool.
◆When clearing a jam.
◆ When touching the safety yoke.
◆When tool is not in use.
◆When moving to a different work area.
Such precautionary measures reduce the risk
of injury to persons.
Always disconnect air source:
●
●
●
LOADING TOOL
Do not load the tool with fasteners when any
one of the operating controls is activated.
Never place a hand or any part of body in
fastener discharge area of tool.
Never point tool at anyone.
Do not pull the trigger or depress the
workpiece contact as accidental actuation
may occur, possibly causing injury.
●
The warnings and precautions discussed
above cannot cover all possible
conditions and situations that may occur.
It must be understood by the user that
common sense and caution are factors
which cannot be built into this product,
but must be supplied by the user.
WARNING:
!
UNPACKING
This tool has been shipped completely
assembled.
Carefully remove the tool and any
accessories from the box.
Inspect the tool carefully to make sure no
breakage or damage occurred during
shipping.
Do not discard the packing material until you
have carefully inspected and satisfactorily
operated the tool.
If any parts are damaged or missing, please
call .1-866-676-8468
●
●
●
●
●
If any parts are missing do not operate
this tool until the missing parts are
replaced. Failure to do so could result in
possible serious personal injury.
WARNING:
!
Do not attempt to modify this tool or
create accessories not recommended for
use with this tool. Any such alteration or
modification is misuse and could result in
hazardous condition leading to possible
serious personal injury.
WARNING:
!
OPERATIONFEATURES
SPECIFICATIONS
●
●
●
●
LOADING FASTENERS
⒈
⒉
⒊
4.
Connect the tool to the air source.
Insert strip of fasteners rom the rear of
magazine(A). Be sure the fasteners are pointed
downward .(See figure 1 & figure 2)
f
This tool uses a spring loaded bypass lever in
order to load and upload the nails. Once the nails
are properly inserted, pull the pusher(B)
completely back, pressing against the bypass
lever of the pusher.(See figure 3)
Once the pusher hits the back of magazine,
allow the pusher to slide forward and engage the
nails, pushing them to the nose of the tool.
(See figure 4)
Figure 1
Respect the tool as a working implement.
Never engage in horseplay.
Never pull the trigger unless nose is directed
toward the work.
Keep others a safe distance from the tool
while tool is in operation as accidental
actuation may occur, possibly causing injury.
REQUIRES:
AIR INLET:
MAGAZINE CAPACITY:
WEIGHT:
MAXIMUM PRESSURE:
PRESSURE RANGE:
7.00 SCFM with 100
fasteners per minute @ 80 psi
1/4 inch NPT
55 fasteners, 10-12 gauge
7,48 lbs
115 psi
70 psi 115 psi–
PIN SIZE RANGE: 2 inch to 3-1/2 inch
Compatible with all brands of plastic collated
21° full head framing nails.
FEATURES
ONE PIECE DRIVER BLADE
COMFORT-GRIP HANDLE
MAGNESIUM BODY
DUAL-MODE TRIGGER
ADJUSTABLE DEPTH
ANTI-DRY FIRING DESIGN
NON-MARRING SAFETY CONTACT
For increased durability.
For increased comfort and control.
Lightweight tool is great for extended use.
Easily allows for Single or Sequential Firing.
Depth is easily adjustable for various
applications.
Reduces damage on internal components.
Eliminates damage to working surface.
Head of nail
Rear of magazine(A)
INSERT NAIL STRIP
MAXIMUM
LOAD
Figure 2
Nail Hold Back Spring