SKU # TBD Model # HOTC4608B1CD USE AND CARE GUIDE HUSKY 46 IN. 8-DRAWER MOBILE WORKBENCH Questions, problems, missing parts? Before returning to the store, call Husky Customer Service 8 a.m - 6 p.m., EST, Monday-Friday 1-888-43-HUSKY HUSKYTOOLS.
Table of Contents Table of Contents ...................................................... 2 Assembly ............................................................... Safety Information........................................................ 2 Warranty ........................................................................ 3 Operation ................................................................ 7 Maintenance ..........................................................
Warranty The manufacturer warrants the product to be free from defects in materials and workmanship for a period of three (3) years from date of purchase. This warranty applies only to the original consumer and only to products used in normal use and service.
Pre-assembly TOOLS REQUIRED Safety goggles HARDWARE INCLUDED NOTE: Hardware not shown to actual size. AA Part AA BB CC DD Description Bolt M6 x 15L Washer Bolt M8 x 20L 10 mm/13 mm wrench BB CC Quantity 4 16 16 1 SPECIFICATIONS Maximum capacity per drawer (1-7) Maximum capacity per drawer (bottom deep drawer) Maximum capacity (total unit) 75 lbs 100 lbs 1000 lbs NOTE: Begin product assembly close to the final intended location of your cabinet.
Pre-assembly (continued) PACKAGE CONTENTS A J I H B E G C F D Part Description Quantity A Wood top 1 B Side handle 1 C Rolling cabinet 1 D Swivel caster with brake 2 E Drawer slide 75 lbs (pair) 9 F Rigid caster 2 G Drawer 8 H Husky badge 1 I Key (set) 1 J Lock 1 5 HUSKYTOOLS.COM Please contact 1-888-43-HUSKY for further assistance.
Assembly 1 Attaching the side handle 2 Installing the casters □ Attach the side handle (B) to the cabinet using four bolts (AA). □ Tighten all bolts with the 10 mm wrench (DD). CAUTION: Do not over tighten the screws. □ Ensure all cabinet drawers are securely locked into place using the key (I) and lock (J) on the rolling cabinet (C). NOTE: The holes in the cabinet are tapped and do not require nuts. □ □ Lay the rolling cabinet (C) on its back. Use the packaging material to protect the finish.
Operation 2 Removing the drawers 1 Locking and unlocking the unit □ Fully extend and empty the drawer. □ On the slide, lift up the plastic release lever on one slide and push down the plastic release lever on the other slide, and gently pull the drawer out so the slides can ride over the stops. IMPORTANT : The drawers must be fully closed before locking / unlocking the unit. □ To lock the unit, insert the key (I) into the lock (J) and turn it 1/4-turn to the left. Then remove the key.
Maintenance 2 1 Maintaining the casters Maintaining the drawers □ Periodically clean the drawer trim, and inside the drawers with a mild detergent and water. □ Remove grease and oil with a standard, nonflammable cleaning fluid. □ The use of drawer liners is recommended to protect the finish inside the drawers and make the drawers easier to clean. Drawer liners can be purchased at The Home Depot and can be cleaned with soap . and water. □ Lubricate the slides semi-annually with grease or equivalent.
Service Parts J A I B E C F D Part Part # Description Quantity A K2532025 B D6TC04001 Side handle 1 D K03220053 Swivel caster w/brakes 2 E K0204022 9 F K03220053 Rigid caster 2 I K06120021 Key (set) 1 J K06120022 Lock 1 Wood top 1 Drawer slide 75 lbs (pair) 9 HUSKYTOOLS.COM Please contact 1-888-43-HUSKY for further assistance.
Questions, problems, missing parts? Before returning to the store, call Husky Customer Service 8 a.m.-6 p.m., EST, Monday-Friday 1-888-43-HUSKY HUSKYTOOLS.COM Retain this manual for future use.