User Guide

ManualsBrandsHusky ManualsOtherHRDC-U250-061117

2006.08

Please confirm all dimensions and nozzle/gating suitability with Husky prior to machining.

Nozzle Selection Ultra 250

ULTRA 250 DESIGN INFORMATION

Ultra 250 Nozzle Pitch

Minimum nozzle pitch dimensions for the Ultra 250 nozzle are

provided on the right. For applications that exceed 16 drops, .

Nozzles can be grouped in maximum clusters of 8.

• X and Y must be greater than 45.0mm (1.77”).

NOTE:

The sprue minimum radius 31.8 mm (1.25") and the X

and

Y minimum distances must all be satisfied.

NOTE: Minimum distance between outermost nozzle drop

center to outer edge of the manifold plate is 125mm (4.921”). If

reduced distance is required, contact Husky.

R 31.8

[1.25]

18.0

[0.71]

18.0

[0.71]

Summary of content (15 pages)

PAGE 1
Nozzle Selection Ultra 250 ULTRA 250 DESIGN INFORMATION Ultra 250 Nozzle Pitch Minimum nozzle pitch dimensions for the Ultra 250 nozzle are provided on the right. For applications that exceed 16 drops, . Nozzles can be grouped in maximum clusters of 8. • X and Y must be greater than 45.0mm (1.77”). NOTE: The sprue minimum radius 31.8 mm (1.25") and the X and Y minimum distances must all be satisfied. 18.0 [0.71] Y R 31.8 [1.
PAGE 2
Ultra 250 HT-D Nozzle Selection 40.00 [1.574] Plate Sizing - Pocket Detail 20.0 [0.79] 10.0 [0.39] R 0.4 [0.02] L 13.00 - 148.8 [0.512 - 5.858] BL 64.66 - 164.66 [2.546 - 6.483] 13.0 [0.51] SL R 3.0 [0.12] N 5.0 x 6.5 DP. [0.20 x 0.26 DP.] 16.02 0.01 [0.631 0.0004 3.5 [0.14] K 0.5 x 45 [0.02 x 45 ] J 12.7 [0.50] For more than 16 drops. Nominal dimensions shown for layout purpose only. Actual dimensions dependent on operating temperatures.
PAGE 3
Nozzle Selection Ultra 250 HT-D Gate Detail Contact Husky with any gate insert backup concerns. 0.005 0.0002 A Gate Diameter < 1.2mm (0.047") 7.000 + 0.005 0.01 A [0.2756 + 0.0002] 60 0.0004 A G Gate Steel: Hardened tool steels such as 49 - 51 Rc AISI H13 / DIN 1.2344 provide a good combination of strength and ductility. Note: These steels may not offer the desired resistance to abrasive and/or corrosive resins, fillers and/or additives. 0.80 [0.031] 0.4 [0.002 + 0.
PAGE 4
Ultra 250 HT-U Nozzle Selection 40.00 [1.574] Plate Sizing - Pocket Detail 20.0 [0.79] 10.0 [0.39] R 0.4 [0.02] L 13.00 - 148.8 [0.512 - 5.858] BL 64.66 - 164.66 [2.546 - 6.483] 13.0 [0.51] SL R 3.0 [0.12] N 5.0 x 6.5 DP. [0.20 x 0.26 DP.] 16.02 0.01 [0.631 0.0004 3.5 [0.14] K 0.5 x 45 [0.02 x 45 ] J 12.7 [0.50] For more than 16 drops. Nominal dimensions shown for layout purpose only. Actual dimensions dependent on operating temperatures.
PAGE 5
Nozzle Selection Ultra 250 HT-U Gate Detail Contact Husky with any gate insert backup concerns. 0.005 0.0002 A Gate Diameter < 1.2mm (0.047") 7.000 + 0.005 0.01 A [0.2756 + 0.0002] 60 0.0004 A G Gate Steel: Hardened tool steels such as 49 - 51 Rc AISI H13 / DIN 1.2344 provide a good combination of strength and ductility. Note: These steels may not offer the desired resistance to abrasive and/or corrosive resins, fillers and/or additives. 0.80 [0.031] 0.4 [0.002 + 0.
PAGE 6
Ultra 250 HT-T Nozzle Selection 40.00 [1.574] Plate Sizing - Pocket Detail 20.0 [0.79] 10.0 [0.39] R 0.4 [0.02] L 13.00 - 148.8 [0.512 - 5.858] BL 64.66 - 164.66 [2.546 - 6.483] 13.0 [0.51] SL R 3.0 [0.12] N 5.0 x 6.5 DP. [0.20 x 0.26 DP.] 16.02 0.01 [0.631 0.0004 3.5 [0.14] K 0.5 x 45 [0.02 x 45 ] J 12.7 [0.50] For more than 16 drops. Nominal dimensions shown for layout purpose only. Actual dimensions dependent on operating temperatures.
PAGE 7
Nozzle Selection Ultra 250 HT-T Gate Detail Contact Husky with any gate insert backup concerns. 0.005 0.0002 A Gate Diameter < 1.2mm (0.047") 7.000 + 0.005 0.01 A [0.2756 + 0.0002] 60 0.0004 A G Gate Steel: Hardened tool steels such as 49 - 51 Rc AISI H13 / DIN 1.2344 provide a good combination of strength and ductility. Note: These steels may not offer the desired resistance to abrasive and/or corrosive resins, fillers and/or additives. 0.80 [0.031] 0.4 [0.002 + 0.
PAGE 8
Ultra 250 HT-DX Nozzle Selection 40.00 [1.574] Plate Sizing - Pocket Detail 3.5 [0.14] N 16.02 0.01 [0.631 0.0004] R 0.4 [0.02] 20.0 [0.79] 10.0 [0.39] 13.0 [0.51] SL R 3.0 [0.12] For more than 16 drops. L 25.5 - 161.3 [1.00 - 6.35] BL 77.16 - 177.16 [3.04 - 6.98] J 5.0 x 6.5 DP. [0.20 x 0.26 DP.] K 0.5 x 45 [0.02 x 45 ] 12.7 [0.50] Nominal dimensions shown for layout purpose only. Actual dimensions dependent on operating temperatures.
PAGE 9
Nozzle Selection Ultra 250 HT-DX Gate Detail Contact Husky with any gate insert backup concerns. 12.5 [0.49] 0.01 A 0.8 FULL SR Gate Diameter > 1.2mm (0.047") 80 0. 0.8 4 G G 36 SR TAN PT S 0.80 [0.031] 0.4 FULL SR is application specific, contact Husky prior to machining. Please confirm all dimensions and nozzle/gating suitability with Husky prior to machining. 2006.08 SR TAN PT 0.80 [0.031] 0.4 G is application specific, contact Husky prior to machining. 0.10 + 0.
PAGE 10
Ultra 250 HT-TX Nozzle Selection 40.00 [1.574] Plate Sizing - Pocket Detail 3.5 [0.14] N 20.0 [0.79] 10.0 [0.39] 13.0 [0.51] SL R 3.0 [0.12] R 0.4 [0.02] For more than 16 drops. L 25.5 - 161.3 [1.00 - 6.35] BL 77.16 - 177.16 [3.04 - 6.98] J 5.0 x 6.5 DP. [0.20 x 0.26 DP.] 16.02 0.01 [0.631 0.0004] K 0.5 x 45 [0.02 x 45 ] 12.7 [0.50] Nominal dimensions shown for layout purpose only. Actual dimensions dependent on operating temperatures.
PAGE 11
Nozzle Selection Ultra 250 HT-TX Gate Detail Contact Husky with any gate insert backup concerns. Gate Diameter < 1.2mm (0.047") 3.8 [.15] REF SR CENTER R 0.2 [0.08] MAX G Gate Diameter > 1.2mm (0.047") 80 0. 0.8 4 G FULL SR S G is application specific, contact Husky prior to machining. Please confirm all dimensions and nozzle/gating suitability with Husky prior to machining. 2006.08 38 SR TAN PT 0.80 [0.031] 0.4 G is application specific, contact Husky prior to machining. 0.10 + 0.
PAGE 12
Ultra 250 HS Nozzle Selection Plate Sizing - Pocket Detail 75.3 [2.97] 60.0 [2.36] ) (X2 40 ) 40 (X2 58 (X2 ) (X2 ) 45 WIRE GROOVE 12.7 [0.50] WIRE GROOVE M6 X 12.0 DP. (X4) 80.0 [3.15] 30.64 [1.206] REF - 10.0 [0.39] WIRE GROOVE 12.45 [0.490] REF 58 M6 X 12.0 DP. (X4) 19.93 [0.785] REF 47.0 [1.85] 25.71 [1.012] REF 21.10 +- 0.01 PL - BL + [0.831 + 0.0004] - 15.10 [0.594] 5.00 [0.197] LOC. RING RELIEF LR DIA. +0.001 97.01 +0.02 -0.00 3.819 -0.000 63.0 [2.480] SR Orifice +0.001 +0.
PAGE 13
Nozzle Selection Ultra 250 HS Dimensions Ultra 250 Hot Sprue ‘A’ Dimension Chart (Thermal Gate) PL (Plate Length) LR DIA HT-D/HT-T/HT-U: 86.22 (3.394") - 206.4 (8.129") HT-DX/HT-TX: 98.76 (3.888") - 219.02 (8.622") 101.31 (3.99") 101.57 (4") 100 (3.94") 120 (4.72") 125 (4.92") 160 (6.30") LR RELIEF DIA 105 (4.13") 105 (4.13") 105 (4.13") 124 (4.88") 129 (5.08") 163.71 (6.45") RAD ORIFICE FLAT 10.00 (.394") 12.70 (.500") 15.50 (.610") 6.35 (.25") 8.00 (.
PAGE 14
Ultra 250 HS Nozzle Selection Gate Detail HT-D / HT-T / HT-U Contact Husky with any gate insert backup concerns. 0.005 0.0002 A Gate Diameter < 1.2mm (0.047") 7.000 + 0.005 0.01 A [0.2756 + 0.0002] 60 0.0004 A Gate Steel: Hardened tool steels such as 49 - 51 Rc AISI H13 / DIN 1.2344 provide a good combination of strength and ductility. Note: These steels may not offer the desired resistance to abrasive and/or corrosive resins, fillers and/or additives. 0.80 [0.031] 0.4 S G SR 2.80 [0.
PAGE 15
Nozzle Selection Ultra 250 HS Gate Detail HT-DX / HT-TX Contact Husky with any gate insert backup concerns 12.5 [0.49] A METRIC IMPERIAL Gate Diameter < 1.2mm (0.047") 0.005 0.0002 60 0.01 A 0.0004 A 4 0.4 0.8 0. R 0.8 [0.03] 80 3.60 [0.142] [0.2756 +0.0002] SR 2.80 [0.110] G S G SR TAN PT 0.80 [0.031] 0.4 0.05 + 0.03 0.8 20 15.9 [0.63] R 0.8 [0.03] 20.1 [0.79] 0.8 6.80 [0.268] [0.002 + 0.001] 7.000 + 0.005 0.8 1.30 [0.