Operators Manual
Table Of Contents
- Contents
- Introduction
- Safety
- Assembly
- Operation
- Maintenance
- Introduction
- Maintenance schedule
- Maintenance and checks of the safety devices on the product
- To do a check of the brake band
- To do a check of the front hand guard and the chain brake activation
- To do a check of the chain brake
- To do a check of the throttle trigger and throttle trigger lockout
- To do a check of the chain catcher
- To do a check of the right hand guard
- To do a check of the vibration damping system
- To do a check of the start/stop switch
- To do a check of the muffler
- To adjust the idle speed screw (T)
- To examine if the carburetor is correctly adjusted
- To replace a broken or worn starter rope
- To tighten the recoil spring
- To assemble the starter housing on the product
- To clean the air filter
- To do a check of the spark plug
- To sharpen the saw chain
- To adjust the tension of the saw chain
- To do a check of the saw chain lubrication
- To do a check of the spur sprocket
- To examine the cutting equipment
- To do a check of the guide bar
- To do maintenance on the fuel tank and the chain oil tank
- To clean the cooling system
- Troubleshooting
- Transportation and storage
- To prepare your product for long-term storage
- Technical data
- Accessories
- EC Declaration of Conformity
- Introducción
- Seguridad
- Montaje
- Funcionamiento
- Mantenimiento
- Introducción
- Programa de mantenimiento
- Mantenimiento y comprobaciones de los dispositivos de seguridad del producto
- Comprobación de la cinta de freno
- Comprobar la protección contra reculadas y la activación del freno de cadena
- Comprobación del freno de cadena
- Comprobación del acelerador y del bloqueo del acelerador
- Comprobación del captor de cadena
- Comprobación de la protección de la mano derecha
- Comprobación del sistema amortiguador de vibraciones
- Comprobación del interruptor de arranque/parada
- Comprobación del silenciador
- Ajuste del tornillo de ralentí (T)
- Inspección para comprobar si el carburador está bien ajustado
- Sustitución de una cuerda de arranque rota o desgastada
- Tensado del muelle de retorno
- Montaje del cuerpo del mecanismo de arranque en el producto
- Para limpiar el filtro de aire
- Mantenimiento de la bujía
- Para afilar la cadena de sierra
- Ajuste de la tensión de la cadena de sierra
- Para comprobar la lubricación de la cadena de sierra
- Comprobación del piñón Spur
- Para inspeccionar el equipo de corte
- Comprobación de la espada
- Mantenimiento del depósito de combustible y del depósito de aceite para cadena
- Para limpiar el sistema de refrigeración
- Resolución de problemas
- Transporte y almacenamiento
- Preparación del producto para un almacenamiento prolongado
- Datos técnicos
- Accesorios
- Declaración CE de conformidad
- Introdução
- Segurança
- Montagem
- Funcionamento
- Manutenção
- Introdução
- Esquema de manutenção
- Manutenção e verificação dos dispositivos de segurança no produto
- Verificar a faixa do travão
- Verificar a proteção anti-retrocesso e a ativação do travão da corrente
- Verificar o travão da corrente
- Verificar o acelerador e o bloqueio do acelerador
- Verificar o retentor de corrente
- Verificar a proteção da mão direita
- Verificar o sistema antivibração
- Verificar o interruptor de arranque/paragem
- Verificar o silenciador
- Ajustar o parafuso da velocidade de ralenti (T)
- Verificar se o carburador está corretamente ajustado
- Substituição de um cabo de arranque gasto ou partido
- Apertar a mola de retorno
- Montar a caixa do dispositivo de arranque no produto
- Para limpar o filtro de ar
- Verificar a vela de ignição
- Para afiar a corrente da serra
- Ajustar a tensão da corrente da serra
- Para verificar a lubrificação da corrente da serra
- Verificar o pinhão de impulso
- Para examinar o equipamento de corte
- Verificar a lâmina-guia
- Efetuar a manutenção dos depósitos de combustível e de óleo de corrente
- Limpar o sistema de arrefecimento
- Resolução de problemas
- Transporte e armazenamento
- Preparar o produto para um armazenamento a longo prazo
- Especificações técnicas
- Acessórios
- Declaração CE de conformidade
near the guide bar, it is possible that the chain brake
does not have time to stop the saw chain before it
hits you.
WARNING: Only you and the correct
working technique can prevent kickbacks.
To start the product
To prepare to start with a cold engine
WARNING: The chain brake must be
engaged when the product is started to
decrease the risk of injury.
1. Move the front hand guard forward to engage the
chain brake. (Fig. 42)
2. Move the start/stop switch to position 1.
3. Pull the choke control (A) out to set it in choke
position.
4. Push the air purge bulb (B) approximately 6 times or
until fuel starts to fill the bulb. It is not necessary to
fill the air purge bulb fully. (Fig. 43)
5. Continue to
To start the product on page 15
for
more instructions.
To prepare start with a warm engine
WARNING: The chain brake must be
engaged when the product is started to
decrease the risk of injury.
1. Move the front hand guard forward to engage the
chain brake. (Fig. 42)
2. Move the start/stop switch to position 1.
3. Push the air purge bulb approximately 6 times or
until fuel starts to fill the bulb. It is not necessary to
fill the air purge bulb fully. (Fig. 44)
4. Continue to
To start the product on page 15
for
more instructions.
To start the product
WARNING: You must keep your feet in a
stable position when you start the product.
WARNING: If the saw chain rotates at idle
speed, speak to your servicing dealer and
do not use the product.
1. Put the product on the ground.
2. Put your left hand on the front handle.
3. Put your right foot into the footgrip on the rear
handle.
4. Pull the starter rope handle slowly with your right
hand until you feel resistance.
WARNING: Do not twist the starter rope
around your hand.
5. Pull the starter rope handle quickly and with force.
(Fig. 45)
CAUTION: Do not pull the starter rope to
full extension and do not let go of the
starter rope handle. This can cause
damage to the product.
a) If you start your product with a cold engine, pull
the starter rope handle until the engine fires.
Note: You can identify when the engine fires
through a "puff" sound.
b) Disengage the choke.
6. Pull the starter rope handle until the engine starts.
7. For start with a cold engine, quickly disengage the
throttle trigger lockout to set the product to idle
speed. (Fig. 46)
8. Move the front hand guard rearward to disengage
the chain brake. (Fig. 24)
9. Use the product.
To stop the product
• Push the start/stop switch to position 0 to stop the
engine. (Fig. 28)
Pull stroke and push stroke
You can cut through wood with the product in 2 different
positions.
• To cut on the pull stroke is when you cut with the
bottom of the guide bar. The saw chain pulls through
the tree when you cut. In this position you have
better control of the product and the position of the
kickback zone.
(Fig. 47)
• To cut on the push stroke is when you cut with the
top of the guide bar. The saw chain pushes the
product in the direction of the operator.
(Fig. 48)
WARNING:
If the saw chain is caught in
the trunk, the product can be pushed at
you. Hold the product tightly and make
sure that the kickback zone of the guide
bar does not touch the tree and causes a
kickback.
(Fig. 49)
930 - 003 - 06.03.2019
15