Operators Manual
Table Of Contents
- Contents
- Introduction
- Safety
- Assembly
- Operation
- Maintenance
- Introduction
- Maintenance schedule
- Maintenance and checks of the safety devices on the product
- To do a check of the brake band
- To do a check of the front hand guard and the chain brake activation
- To do a check of the chain brake
- To do a check of the throttle trigger and throttle trigger lockout
- To do a check of the chain catcher
- To do a check of the right hand guard
- To do a check of the vibration damping system
- To do a check of the start/stop switch
- To do a check of the muffler
- To adjust the idle speed screw (T)
- To examine if the carburetor is correctly adjusted
- To replace a broken or worn starter rope
- To tighten the recoil spring
- To assemble the starter housing on the product
- To clean the air filter
- To do a check of the spark plug
- To sharpen the saw chain
- To adjust the tension of the saw chain
- To do a check of the saw chain lubrication
- To do a check of the spur sprocket
- To examine the cutting equipment
- To do a check of the guide bar
- To do maintenance on the fuel tank and the chain oil tank
- To clean the cooling system
- Troubleshooting
- Transportation and storage
- To prepare your product for long-term storage
- Technical data
- Accessories
- EC Declaration of Conformity
- Introducción
- Seguridad
- Montaje
- Funcionamiento
- Mantenimiento
- Introducción
- Programa de mantenimiento
- Mantenimiento y comprobaciones de los dispositivos de seguridad del producto
- Comprobación de la cinta de freno
- Comprobar la protección contra reculadas y la activación del freno de cadena
- Comprobación del freno de cadena
- Comprobación del acelerador y del bloqueo del acelerador
- Comprobación del captor de cadena
- Comprobación de la protección de la mano derecha
- Comprobación del sistema amortiguador de vibraciones
- Comprobación del interruptor de arranque/parada
- Comprobación del silenciador
- Ajuste del tornillo de ralentí (T)
- Inspección para comprobar si el carburador está bien ajustado
- Sustitución de una cuerda de arranque rota o desgastada
- Tensado del muelle de retorno
- Montaje del cuerpo del mecanismo de arranque en el producto
- Para limpiar el filtro de aire
- Mantenimiento de la bujía
- Para afilar la cadena de sierra
- Ajuste de la tensión de la cadena de sierra
- Para comprobar la lubricación de la cadena de sierra
- Comprobación del piñón Spur
- Para inspeccionar el equipo de corte
- Comprobación de la espada
- Mantenimiento del depósito de combustible y del depósito de aceite para cadena
- Para limpiar el sistema de refrigeración
- Resolución de problemas
- Transporte y almacenamiento
- Preparación del producto para un almacenamiento prolongado
- Datos técnicos
- Accesorios
- Declaración CE de conformidad
- Introdução
- Segurança
- Montagem
- Funcionamento
- Manutenção
- Introdução
- Esquema de manutenção
- Manutenção e verificação dos dispositivos de segurança no produto
- Verificar a faixa do travão
- Verificar a proteção anti-retrocesso e a ativação do travão da corrente
- Verificar o travão da corrente
- Verificar o acelerador e o bloqueio do acelerador
- Verificar o retentor de corrente
- Verificar a proteção da mão direita
- Verificar o sistema antivibração
- Verificar o interruptor de arranque/paragem
- Verificar o silenciador
- Ajustar o parafuso da velocidade de ralenti (T)
- Verificar se o carburador está corretamente ajustado
- Substituição de um cabo de arranque gasto ou partido
- Apertar a mola de retorno
- Montar a caixa do dispositivo de arranque no produto
- Para limpar o filtro de ar
- Verificar a vela de ignição
- Para afiar a corrente da serra
- Ajustar a tensão da corrente da serra
- Para verificar a lubrificação da corrente da serra
- Verificar o pinhão de impulso
- Para examinar o equipamento de corte
- Verificar a lâmina-guia
- Efetuar a manutenção dos depósitos de combustível e de óleo de corrente
- Limpar o sistema de arrefecimento
- Resolução de problemas
- Transporte e armazenamento
- Preparar o produto para um armazenamento a longo prazo
- Especificações técnicas
- Acessórios
- Declaração CE de conformidade
a check of the guide bar on page 24
for
instructions. Speak to your servicing dealer if the
maintenance steps does not help.
To do a check of the spur sprocket
The clutch drum has a spur sprocket that is welded on
the clutch drum.
(Fig. 121)
• Regularly do a visual check of the degree of wear on
the spur sprocket. Replace the clutch drum with the
spur sprocket if there is too much wear.
To examine the cutting equipment
1. Make sure that there are no cracks in rivets and links
and that no rivets are loose. Replace if it is
necessary. (Fig. 122)
2. Make sure that the saw chain is easy to bend.
Replace the saw chain if it is rigid.
3. Compare the saw chain with a new saw chain to
examine if the rivets and links are worn.
4. Replace the saw chain when the longest part of the
cutting tooth is less than 4 mm/0.16 in. Also replace
the saw chain if there are cracks on the cutters. (Fig.
123)
To do a check of the guide bar
1. Make sure that the oil channel is not blocked. Clean
if it is necessary. (Fig. 124)
2. Examine if there are burrs on the edges of the guide
bar. Remove the burrs using a file. (Fig. 125)
3. Clean the groove in the guide bar. (Fig. 126)
4. Examine the groove in the guide bar for wear.
Replace the guide bar if it is necessary. (Fig. 127)
5. Examine if the guide bar tip is rough or very worn.
(Fig. 128)
6. Make sure that the bar tip sprocket turns freely and
that the lubricating hole in the bar tip sprocket is not
blocked. Clean and lubricate if it is necessary. (Fig.
129)
7. Turn the guide bar daily to extend its life cycle. (Fig.
130)
To do maintenance on the fuel tank
and the chain oil tank
• Drain and clean the fuel tank and the chain oil tank
regularly.
• Replace the fuel filter yearly or more frequently if
necessary.
CAUTION: Contamination in the tanks
causes malfunction.
To clean the cooling system
The cooling system keeps the engine temperature
down. The cooling system includes the air intake on the
starter (A), the air guide plate (B), the pawls on the
flywheel (C), the cooling fins on the cylinder (D), and the
cylinder cover (E).
(Fig. 131)
1. Clean the cooling system with a brush weekly or
more frequently if it is necessary.
2. Make sure that the cooling system is not dirty or
blocked.
CAUTION:
A dirty or blocked cooling
system can make the product too hot,
which can cause damage to the product.
Troubleshooting
The engine does not start
Product part to examine Possible cause Action
Starter pawls The starter pawls are blocked. Adjust or replace the starter pawls.
Clean around the pawls.
Speak to an approved service work-
shop.
24 930 - 003 - 06.03.2019