Owner's Manual

ManualsBrandsHusqvarna ManualsMotorcycle125 TC EU Motorcycle

100

20 TECHNICAL DATA 90

Transmission ratio

First gear 14:28

Second gear 15:24

Third gear 18:24

Fourth gear 21:24

Fifth gear 22:21

Ignition Contactless controlled fully electronic ignition with digital ignition

adjustment, type Kokusan

Ignition point (BTDC) 1.9 mm (0.075 in)

Spark plug NGK BR 8 ECM

Spark plug electrode gap 0.60 mm (0.0236 in)

Starting aid Kick starter

20.2 Engine tightening torques

20.2.1 125 TC EU

Screw, inner membrane sheets EJOT DELTA PT

35x25 1 Nm (0.7 lbf ft) –

Screw, membrane support plate EJOT DELTA PT

30x12 1 Nm (0.7 lbf ft) –

Screw, outer membrane sheets EJOT DELTA PT

30x6 1 Nm (0.7 lbf ft) –

Locking screw for bearing M5 6 Nm (4.4 lbf ft) Loctite

243™

Screw, alternator cover M5 5 Nm (3.7 lbf ft) –

Screw, centrifugal timer M5 8 Nm (5.9 lbf ft) Loctite

243™

Screw, exhaust control cover M5 5 Nm (3.7 lbf ft) –

Screw, exhaust flange M5 6 Nm (4.4 lbf ft) –

Screw, ignition system/stator M5 6 Nm (4.4 lbf ft) Loctite

222™

Screw, lock washer, axle for control flap M5 6 Nm (4.4 lbf ft) Loctite

243™

Screw, locking lever M5 6 Nm (4.4 lbf ft) Loctite

243™

Screw, water pump wheel M5 6 Nm (4.4 lbf ft) Loctite

243™

Adjustment cable, exhaust control M6 10 Nm (7.4 lbf ft) Loctite

243™

Bleeder screw, cylinder head M6 10 Nm (7.4 lbf ft) –

Screw, clutch cover M6 10 Nm (7.4 lbf ft) –

Screw, clutch slave cylinder M6 10 Nm (7.4 lbf ft) Loctite

243™

Screw, clutch spring M6 10 Nm (7.4 lbf ft) –

Screw, engine case M6 10 Nm (7.4 lbf ft) –

Screw, exhaust control M6 10 Nm (7.4 lbf ft) –

Screw, gear oil level check M6 10 Nm (7.4 lbf ft) –

Screw, intake flange/reed valve housing M6 10 Nm (7.4 lbf ft) –

Screw, kick starter stop plate M6 10 Nm (7.4 lbf ft) Loctite

243™

Screw, shift lever M6 14 Nm (10.3 lbf ft) Loctite

243™

Screw, shifting gate M6 10 Nm (7.4 lbf ft) Loctite

243™

Screw, water pump cover M6 10 Nm (7.4 lbf ft) Loctite

243™

Screw, cylinder head M7 18 Nm (13.3 lbf ft) –

Axle for control flap, exhaust control M8 Step 1

3 Nm (2.2 lbf ft)

Step 2 (loosen, counter-

clockwise)

1/4 turn

–

Nut, cylinder base M8 30 Nm (22.1 lbf ft) –

Screw, kick starter M8 25 Nm (18.4 lbf ft) Loctite

243™

Screw, shift drum locating M8 25 Nm (18.4 lbf ft) Loctite

243™

Stud, cylinder base M8 35 Nm (25.8 lbf ft) –

Drain plug, water pump cover M10x1 15 Nm (11.1 lbf ft) –

Gear oil drain plug M10x1 15 Nm (11.1 lbf ft) –