Operators Manual
Table Of Contents
- Contents
- Introduction
- Safety
- Assembly
- Operation
- Maintenance
- Introduction
- Maintenance schedule
- Maintenance and checks of the safety devices on the product
- To do a check of the brake band
- To do a check of the front hand guard and the chain brake activation
- To do a check of the chain brake
- To do a check of the throttle trigger and throttle trigger lockout
- To do a check of the chain catcher
- To do a check of the right hand guard
- To do a check of the vibration damping system
- To do a check of the start/stop switch
- To do a check of the muffler
- To adjust the idle speed screw (T)
- To examine if the carburetor is correctly adjusted
- To replace a broken or worn starter rope
- To tighten the recoil spring
- To assemble the starter housing on the product
- To clean the air filter
- To do a check of the spark plug
- To sharpen the saw chain
- To adjust the tension of the saw chain
- To do a check of the saw chain lubrication
- To do a check of the spur sprocket
- To examine the cutting equipment
- To do a check of the guide bar
- To do maintenance on the fuel tank and the chain oil tank
- To clean the cooling system
- Troubleshooting
- Transportation and storage
- To prepare your product for long-term storage
- Technical data
- Accessories
- EC Declaration of Conformity
- Introducción
- Seguridad
- Montaje
- Funcionamiento
- Mantenimiento
- Introducción
- Programa de mantenimiento
- Mantenimiento y comprobaciones de los dispositivos de seguridad del producto
- Comprobación de la cinta de freno
- Comprobar la protección contra reculadas y la activación del freno de cadena
- Comprobación del freno de cadena
- Comprobación del acelerador y del bloqueo del acelerador
- Comprobación del captor de cadena
- Comprobación de la protección de la mano derecha
- Comprobación del sistema amortiguador de vibraciones
- Comprobación del interruptor de arranque/parada
- Comprobación del silenciador
- Ajuste del tornillo de ralentí (T)
- Inspección para comprobar si el carburador está bien ajustado
- Sustitución de una cuerda de arranque rota o desgastada
- Tensado del muelle de retorno
- Montaje del cuerpo del mecanismo de arranque en el producto
- Para limpiar el filtro de aire
- Mantenimiento de la bujía
- Para afilar la cadena de sierra
- Ajuste de la tensión de la cadena de sierra
- Para comprobar la lubricación de la cadena de sierra
- Comprobación del piñón Spur
- Para inspeccionar el equipo de corte
- Comprobación de la espada
- Mantenimiento del depósito de combustible y del depósito de aceite para cadena
- Para limpiar el sistema de refrigeración
- Resolución de problemas
- Transporte y almacenamiento
- Preparación del producto para un almacenamiento prolongado
- Datos técnicos
- Accesorios
- Declaración CE de conformidad
- Introdução
- Segurança
- Montagem
- Funcionamento
- Manutenção
- Introdução
- Esquema de manutenção
- Manutenção e verificação dos dispositivos de segurança no produto
- Verificar a faixa do travão
- Verificar a proteção anti-retrocesso e a ativação do travão da corrente
- Verificar o travão da corrente
- Verificar o acelerador e o bloqueio do acelerador
- Verificar o retentor de corrente
- Verificar a proteção da mão direita
- Verificar o sistema antivibração
- Verificar o interruptor de arranque/paragem
- Verificar o silenciador
- Ajustar o parafuso da velocidade de ralenti (T)
- Verificar se o carburador está corretamente ajustado
- Substituição de um cabo de arranque gasto ou partido
- Apertar a mola de retorno
- Montar a caixa do dispositivo de arranque no produto
- Para limpar o filtro de ar
- Verificar a vela de ignição
- Para afiar a corrente da serra
- Ajustar a tensão da corrente da serra
- Para verificar a lubrificação da corrente da serra
- Verificar o pinhão de impulso
- Para examinar o equipamento de corte
- Verificar a lâmina-guia
- Efetuar a manutenção dos depósitos de combustível e de óleo de corrente
- Limpar o sistema de arrefecimento
- Resolução de problemas
- Transporte e armazenamento
- Preparar o produto para um armazenamento a longo prazo
- Especificações técnicas
- Acessórios
- Declaração CE de conformidade
• Never allow children to use or be in the vicinity of the
product. As the product is equipped with a spring-
loaded start/stop switch and can be started by low
speed and force on the starter handle, even small
children under some circumstances can produce the
force necessary to start the product. This can mean
a risk of serious personal injury. Therefore remove
the spark plug cap when the product is not under
close supervision.
• You must have a steady stance in order to have full
control of the product. Never work standing on a
ladder, in a tree or where you do not have a firm
ground to stand on.
(Fig. 17)
• Lack of concentration can lead to kickback if the
kickback zone of the bar accidentally touches a
branch, nearby tree or some other object.
(Fig. 18)
• Never use the product by holding it with one hand.
This product is not safely controlled with one hand.
• Always hold the product with both hands. The right
hand should be on the rear handle, and the left hand
on the front handle. All people, whether right or left
handed, should use this grip. Use a firm grip with
thumbs and fingers encircling the handles. This grip
minimizes the risk of kickback and lets you keep the
product under control. Do not let go of the handles!
(Fig. 19)
• Never use the product above shoulder height.
(Fig. 20)
• Do not use the product in a situation where you
cannot call for help in case of an accident.
• Before moving your product, switch off the engine
and lock the saw chain using the chain brake. Carry
the product with the guide bar and saw chain
pointing backwards. Fit a transportation guard to the
guide bar before transporting the product or carrying
it for any distance.
• When you put the product on the ground, lock the
saw chain using the chain brake and ensure you
have a constant view of the product. Switch the
engine off before leaving your product for any length
of time.
• Sometimes chips get stuck in the clutch cover
causing the saw chain to jam. Always stop the
engine before cleaning.
• Running an engine in a confined or badly ventilated
area can result in death due to carbon monoxide
poisoning.
• The exhaust fumes from the engine are hot and may
contain sparks which can start a fire. Do not start the
product indoors or near flammable material.
• Use the chain brake as a parking brake when you
start the product and when you move short
distances. Always carry the product in the front
handle. This decreases the risk that you or a person
near you get hit by the saw chain.
• Overexposure to vibration can lead to circulatory
damage or nerve damage in people who have
impaired circulation. Contact your doctor if you
experience symptoms of overexposure to vibration.
Such symptoms include numbness, loss of feeling,
tingling, pricking, pain, loss of strength, changes in
skin colour or condition. These symptoms normally
appear in the fingers, hands or wrists. These
symptoms may be increased in cold temperatures.
• It is not possible to cover every conceivable situation
you can face when using this product. Always
exercise care and use your common sense. Avoid all
situations which you consider to be beyond your
capability. If you still feel uncertain about operating
procedures after reading these instructions, you
should consult an expert before continuing. Do not
hesitate to contact your dealer or Husqvarna if you
have any questions about the use of the product. We
will willingly be of service and provide you with
advice as well as help you to use your product both
efficiently and safely. Attend a training course in
chainsaw usage if possible. Your dealer, forestry
school or your library can provide information about
which training materials and courses are available.
(Fig. 21)
Personal protective equipment
WARNING: Read the warning instructions
that follow before you use the product.
(Fig. 22)
• Most chainsaw accidents occur when the saw chain
touches the operator. You must use approved
personal protective equipment during operation.
Personal protective equipment does not give you full
protection from injuries but it decreases the degree
of injury if an accident occurs. Speak to your
servicing dealer for recommendations about which
equipment to use.
• Your clothing must be close-fitting but not limit your
movements. Regularly do a check of the condition of
the personal protective equipment.
• Use an approved protective helmet.
• Use approved hearing protection. Long-term
exposure to noise can result in permanent damage
to the hearing.
• Use protective glasses or a face visor to decrease
the risk of injury from thrown objects. The product
can throw objects, such as wood chips, small pieces
of wood and more, at large force. This can result in
serious injury, especially to the eyes.
• Use gloves with saw protection.
• Use pants with saw protection.
• Use boots with saw protection, steel toe-cap and
non-slip sole.
• Always have a first-aid kit with you.
10
930 - 003 - 06.03.2019