Operators Manual
Table Of Contents
- Contents
- Introduction
- Safety
- Assembly
- Operation
- Maintenance
- Introduction
- Maintenance schedule
- Maintenance and checks of the safety devices on the product
- To do a check of the brake band
- To do a check of the front hand guard and the chain brake activation
- To do a check of the chain brake
- To do a check of the throttle trigger and throttle trigger lockout
- To do a check of the chain catcher
- To do a check of the right hand guard
- To do a check of the vibration damping system
- To do a check of the start/stop switch
- To do a check of the muffler
- To adjust the idle speed screw (T)
- To examine if the carburetor is correctly adjusted
- To replace a broken or worn starter rope
- To tighten the recoil spring
- To assemble the starter housing on the product
- To clean the air filter
- To do a check of the spark plug
- To sharpen the saw chain
- To adjust the tension of the saw chain
- To do a check of the saw chain lubrication
- To do a check of the spur sprocket
- To examine the cutting equipment
- To do a check of the guide bar
- To do maintenance on the fuel tank and the chain oil tank
- To clean the cooling system
- Troubleshooting
- Transportation and storage
- To prepare your product for long-term storage
- Technical data
- Accessories
- EC Declaration of Conformity
- Introducción
- Seguridad
- Montaje
- Funcionamiento
- Mantenimiento
- Introducción
- Programa de mantenimiento
- Mantenimiento y comprobaciones de los dispositivos de seguridad del producto
- Comprobación de la cinta de freno
- Comprobar la protección contra reculadas y la activación del freno de cadena
- Comprobación del freno de cadena
- Comprobación del acelerador y del bloqueo del acelerador
- Comprobación del captor de cadena
- Comprobación de la protección de la mano derecha
- Comprobación del sistema amortiguador de vibraciones
- Comprobación del interruptor de arranque/parada
- Comprobación del silenciador
- Ajuste del tornillo de ralentí (T)
- Inspección para comprobar si el carburador está bien ajustado
- Sustitución de una cuerda de arranque rota o desgastada
- Tensado del muelle de retorno
- Montaje del cuerpo del mecanismo de arranque en el producto
- Para limpiar el filtro de aire
- Mantenimiento de la bujía
- Para afilar la cadena de sierra
- Ajuste de la tensión de la cadena de sierra
- Para comprobar la lubricación de la cadena de sierra
- Comprobación del piñón Spur
- Para inspeccionar el equipo de corte
- Comprobación de la espada
- Mantenimiento del depósito de combustible y del depósito de aceite para cadena
- Para limpiar el sistema de refrigeración
- Resolución de problemas
- Transporte y almacenamiento
- Preparación del producto para un almacenamiento prolongado
- Datos técnicos
- Accesorios
- Declaración CE de conformidad
- Introdução
- Segurança
- Montagem
- Funcionamento
- Manutenção
- Introdução
- Esquema de manutenção
- Manutenção e verificação dos dispositivos de segurança no produto
- Verificar a faixa do travão
- Verificar a proteção anti-retrocesso e a ativação do travão da corrente
- Verificar o travão da corrente
- Verificar o acelerador e o bloqueio do acelerador
- Verificar o retentor de corrente
- Verificar a proteção da mão direita
- Verificar o sistema antivibração
- Verificar o interruptor de arranque/paragem
- Verificar o silenciador
- Ajustar o parafuso da velocidade de ralenti (T)
- Verificar se o carburador está corretamente ajustado
- Substituição de um cabo de arranque gasto ou partido
- Apertar a mola de retorno
- Montar a caixa do dispositivo de arranque no produto
- Para limpar o filtro de ar
- Verificar a vela de ignição
- Para afiar a corrente da serra
- Ajustar a tensão da corrente da serra
- Para verificar a lubrificação da corrente da serra
- Verificar o pinhão de impulso
- Para examinar o equipamento de corte
- Verificar a lâmina-guia
- Efetuar a manutenção dos depósitos de combustível e de óleo de corrente
- Limpar o sistema de arrefecimento
- Resolução de problemas
- Transporte e armazenamento
- Preparar o produto para um armazenamento a longo prazo
- Especificações técnicas
- Acessórios
- Declaração CE de conformidade
Daily maintenance Weekly maintenance Monthly maintenance
Make sure that there is no damage
on the right hand guard.
Make sure that the muffler is correct-
ly attached, has no damages and
that no parts of the muffler are miss-
ing.
Clean or replace the air filter. Refer
to
To clean the air filter on page 22
.
Maintenance and checks of the safety
devices on the product
To do a check of the brake band
1. Use a brush to remove wood dust, resin and dirt
from the chain brake and clutch drum. Dirt and wear
can decrease the function of the brake. (Fig. 84)
2. Do a check of the brake band. The brake band must
be at a minimum of 0.6 mm/0.024 in thick at its
thinnest point.
To do a check of the front hand guard and the
chain brake activation
1. Make sure that the front hand guard is not damaged
and that there are no defects, such as cracks.
2. Make sure that the front hand guard moves freely
and that it is attached safely to the clutch cover. (Fig.
85)
3. Hold the product with 2 hands above a stump or
other stable surface.
WARNING: The engine must be off.
4. Let go of the front handle and let the guide bar tip fall
against the stump. (Fig. 86)
5. Make sure that the chain brake engages as the
guide bar tip hits the stump.
To do a check of the chain brake
1. Start the product. Refer to
To start the product on
page 15
for instructions.
WARNING:
Make sure that the saw
chain does not touch the ground or other
objects.
2. Hold the product tightly.
3. Apply full throttle and tilt your left wrist against the
front hand guard to engage the chain brake. The
saw chain must stop immediately. (Fig. 87)
WARNING: Do not let go of the front handle.
To do a check of the throttle trigger and
throttle trigger lockout
1. Make sure that the throttle trigger and throttle trigger
lockout move freely and that the return spring works
correctly. (Fig. 46)
2. Press down the throttle trigger lockout and make
sure that it goes back to its initial position when you
release it. (Fig. 88)
3. Make sure that the throttle trigger is locked at the
idle position when the throttle trigger lockout is
released. (Fig. 89)
4. Start the product and apply full throttle.
5. Release the throttle trigger and make sure that the
saw chain stops and stays stationary.
WARNING: If the saw chain rotates
when the throttle trigger is in the idle
position, speak to your servicing dealer.
To do a check of the chain catcher
1. Make sure that there is no damage on the chain
catcher.
2. Make sure that the chain catcher is stable and
attached to the body of the product. (Fig. 26)
To do a check of the right hand guard
• Make sure that the right hand guard is not damaged
and that there are no defects, such as cracks. (Fig.
27)
To do a check of the vibration damping
system
1. Make sure that there are no cracks or deformation
on the vibration damping units.
2. Make sure that the vibration damping units are
correctly attached to the engine unit and handle unit.
Refer to
Product overview on page 8
for information
about where the vibration damping system is on your
product.
20
930 - 003 - 06.03.2019