Operators Manual
Table Of Contents
- Contents
- Introduction
- Safety
- Assembly
- Operation
- Maintenance
- Introduction
- Maintenance schedule
- Maintenance and checks of the safety devices on the product
- To do a check of the brake band
- To do a check of the front hand guard and the chain brake activation
- To do a check of the chain brake
- To do a check of the throttle trigger and throttle trigger lockout
- To do a check of the chain catcher
- To do a check of the right hand guard
- To do a check of the vibration damping system
- To do a check of the start/stop switch
- To do a check of the muffler
- To adjust the idle speed screw (T)
- To examine if the carburetor is correctly adjusted
- To replace a broken or worn starter rope
- To tighten the recoil spring
- To assemble the starter housing on the product
- To clean the air filter
- To do a check of the spark plug
- To sharpen the saw chain
- To adjust the tension of the saw chain
- To do a check of the saw chain lubrication
- To do a check of the spur sprocket
- To examine the cutting equipment
- To do a check of the guide bar
- To do maintenance on the fuel tank and the chain oil tank
- To clean the cooling system
- Troubleshooting
- Transportation and storage
- To prepare your product for long-term storage
- Technical data
- Accessories
- EC Declaration of Conformity
- Introducción
- Seguridad
- Montaje
- Funcionamiento
- Mantenimiento
- Introducción
- Programa de mantenimiento
- Mantenimiento y comprobaciones de los dispositivos de seguridad del producto
- Comprobación de la cinta de freno
- Comprobar la protección contra reculadas y la activación del freno de cadena
- Comprobación del freno de cadena
- Comprobación del acelerador y del bloqueo del acelerador
- Comprobación del captor de cadena
- Comprobación de la protección de la mano derecha
- Comprobación del sistema amortiguador de vibraciones
- Comprobación del interruptor de arranque/parada
- Comprobación del silenciador
- Ajuste del tornillo de ralentí (T)
- Inspección para comprobar si el carburador está bien ajustado
- Sustitución de una cuerda de arranque rota o desgastada
- Tensado del muelle de retorno
- Montaje del cuerpo del mecanismo de arranque en el producto
- Para limpiar el filtro de aire
- Mantenimiento de la bujía
- Para afilar la cadena de sierra
- Ajuste de la tensión de la cadena de sierra
- Para comprobar la lubricación de la cadena de sierra
- Comprobación del piñón Spur
- Para inspeccionar el equipo de corte
- Comprobación de la espada
- Mantenimiento del depósito de combustible y del depósito de aceite para cadena
- Para limpiar el sistema de refrigeración
- Resolución de problemas
- Transporte y almacenamiento
- Preparación del producto para un almacenamiento prolongado
- Datos técnicos
- Accesorios
- Declaración CE de conformidad
- Introdução
- Segurança
- Montagem
- Funcionamento
- Manutenção
- Introdução
- Esquema de manutenção
- Manutenção e verificação dos dispositivos de segurança no produto
- Verificar a faixa do travão
- Verificar a proteção anti-retrocesso e a ativação do travão da corrente
- Verificar o travão da corrente
- Verificar o acelerador e o bloqueio do acelerador
- Verificar o retentor de corrente
- Verificar a proteção da mão direita
- Verificar o sistema antivibração
- Verificar o interruptor de arranque/paragem
- Verificar o silenciador
- Ajustar o parafuso da velocidade de ralenti (T)
- Verificar se o carburador está corretamente ajustado
- Substituição de um cabo de arranque gasto ou partido
- Apertar a mola de retorno
- Montar a caixa do dispositivo de arranque no produto
- Para limpar o filtro de ar
- Verificar a vela de ignição
- Para afiar a corrente da serra
- Ajustar a tensão da corrente da serra
- Para verificar a lubrificação da corrente da serra
- Verificar o pinhão de impulso
- Para examinar o equipamento de corte
- Verificar a lâmina-guia
- Efetuar a manutenção dos depósitos de combustível e de óleo de corrente
- Limpar o sistema de arrefecimento
- Resolução de problemas
- Transporte e armazenamento
- Preparar o produto para um armazenamento a longo prazo
- Especificações técnicas
- Acessórios
- Declaração CE de conformidade
Contents
Introduction..................................................................... 8
Safety..............................................................................9
Assembly...................................................................... 12
Operation...................................................................... 13
Maintenance................................................................. 18
Troubleshooting............................................................ 24
Transportation and storage...........................................25
To prepare your product for long-term storage.............26
Technical data.............................................................. 26
Accessories.................................................................. 27
EC Declaration of Conformity....................................... 28
Introduction
Intended use
This product is intended for sawing in wood.
Note: National regulations can set limit to the operation
of the product.
Product description
The Husqvarna 120, 125 is a chainsaw model with a
combustion engine.
Work is constantly in progress to increase your safety
and efficiency during operation. Speak to your servicing
dealer for more information.
Product overview
(Fig. 1)
1. Cylinder cover
2. Spark plug and spark plug cap
3. Start/stop switch
4. Rear handle
5. Air filter
6. Fuel tank
7. Chain oil tank
8. Starter rope handle
9. Starter housing
10. Chain brake and front hand guard
11. Front handle
12. Air purge bulb
13. Throttle trigger lockout
14. Right hand guard
15. Clutch cover
16. Chain tensioning screw
17. Brake band
18. Chain catcher
19. Vibration damping system
20. Saw chain
21. Guide bar
22. Bar tip sprocket
23. Transport guard
24. Operator's manual
25. Combination wrench
26. Muffler
27. Carburetor adjuster screws
28. Throttle trigger
29. Information and warning decal
30. Product and serial number plate
31. Starter reminder decal
32. Felling direction mark
Symbols on the product
(Fig. 2) Be careful and use the product correctly.
This product can cause serious injury or
death to the operator or others.
(Fig. 3) Read the operator's manual carefully and
make sure that you understand the
instructions before you use this product.
(Fig. 4) Always wear approved protective helmet,
approved hearing protection and eye
protection.
(Fig. 5) Use 2 hands to operate the product.
(Fig. 6) Do not let the guide bar tip touch an object.
(Fig. 7) Do not operate the product with one hand
only.
(Fig. 8) Warning! Kickback can occur when the
guide bar tip touches an object. A kickback
causes a lightning fast reverse reaction that
throws the guide bar up and in the direction
of the operator. Can cause serious injury.
(Fig. 9) This product complies with applicable EC
Directives.
(Fig. 10) Noise emission to the environment complies
with applicable EC Directives. The noise
emission of the product is specified in
8 930 - 003 - 06.03.2019