Operators Manual
Table Of Contents
- Symbols on the machine:
- Symbols in the operator’s manual:
- Contents
- Dear Customer,
- Before using a new chain saw
- Important
- Always use common sense (2)
- Personal protective equipment
- Machine¢s safety equipment
- Chain brake and front hand guard
- Will my hand always activate the chain brake during a kickback?
- Will my inertia activated chain brake always activate during kickback in the event of a kickback?
- Will my chain brake always protect me from injury in the event of a kickback?
- Throttle trigger lockout
- Chain catcher
- Right hand guard
- Vibration damping system
- Stop switch
- Muffler
- Cutting equipment
- Fitting the bar and chain
- Fuel
- Fueling
- Fuel safety
- Starting and stopping
- Before use: (50)
- General working instructions
- How to avoid kickback
- General
- Carburettor adjustment
- Checking, maintaining and servicing chain saw safety equipment
- Muffler
- Starter housing
- Air filter
- Spark plug
- Needle bearing lubrication
- Cooling system
- ”Air Injection” centrifugal cleaning
- Winter use
- Troubleshooting schedule
- Maintenance schedule
- Technical data
- Guide bar and saw chain combinations
- Saw chain filing and file gauges
- EC Declaration of Conformity
ASSEMBLY
18 – English
1158605-39 Rev.3 2016-09-20
Fitting the bar and chain
135
Check that the chain brake is in disengaged position by
moving the front hand guard towards the front handle.
(38)
Unscrew the bar nut and remove the clutch cover (chain
brake). Take off the transportation guard (A).
(39)
Fit the bar over the bar bolt. Place the bar in its rearmost
position. Place the chain over the drive sprocket and in
the groove on the bar. Begin on the top side of the bar.
(40)
Make sure that the edges of the cutting links are facing
forward on the top edge of the bar.
Mount the clutch cover and remember to fit the chain
adjuster pin in the hole in the bar. Check that the drive
links of the chain fit correctly over the drive sprocket and
that the chain is correctly located in the groove in the bar.
Tighten the bar nut with your fingers.
Tension the chain by turning the chain tensioning screw
cloc
kwise using the combination spanner. The chain
should be tensioned until it does not sag from the
underside of the bar.
(27)
The chain is correctly tensioned when there is no slack on
the underside of the bar, and it can still be turned easily
by hand. Tighten the bar nut with the combination spanner
while holding up the tip of the bar.
(28)
When fitting a new chain, the chain tension has to be
checked frequently until the chain is run-in. Check the
chain tension regularly. A correctly tensioned chain
ensures good cutting performance and long life.
(25)
135e, 135e TrioBrake
Check that the chain brake is in disengaged position by
moving the front hand guard towards the front handle.
(38)
Loosen the chain tensioner wheel and remove the clutch
cover (chain brake). Remove the transport guard. (A)
(41)
Fit the bar over the bar bolts. Place the bar in its rearmost
position. Place the chain over the drive sprocket locate it
in the groove on the bar. Begin on the top edge of the bar.
(40)
Make sure that the edges of the cutting links are facing
forward on the top edge of the bar.
Mount the clutch cover and remember to fit the chain
adjuster pin in the hole in the bar. Check that the drive
links of the chain fit correctly over the drive sprocket and
that the chain is correctly located in the groove in the bar.
Tension the chain by turning the wheel down (+). The
chain should be tensioned until it does not sag from the
underside of the bar
.
(31)
The chain is correctly tensioned when it does not sag from
the underside of the bar, but can still be turned easily by
hand. Hold up the bar tip and tighten the bar knob by
turning the knob clockwise.
(32)
When fitting a new chain, the chain tension has to be
checked frequently until the chain is run-in. Check the
chain tension regularly. A correctly tensioned chain
ensures good cutting performance and long life.
(25)
Fitting a spiked bumper
To fit a spiked bumper – contact your service agent. (42)
!
WARNING! Always wear gloves, when
working with the chain.