Instruction Manual
Table Of Contents
- Contents
- Introduction
- Safety
- Assembly
- Operation
- Maintenance
- Maintenance schedule
- Daily maintenance
- Weekly maintenance
- Monthly maintenance
- Yearly maintenance
- Intermittent maintenance
- To adjust the idle speed
- To do maintenance on the spark arrester mesh
- To do maintenance on the spark plug
- To clean the air filter
- To sharpen the saw chain
- To lubricate the cutting equipment
- Transportation
- Storage
- Technical Data
- Accessories
- Declaration of Conformity
- Съдържание
- Въведение
- Безопасност
- Монтиране
- Експлоатация
- Поддръжка
- График за техническо обслужване
- Всекидневно обслужване
- Седмично техническо обслужване
- Месечно техническо обслужване
- Ежегодно обслужване
- Периодично обслужване
- Регулиране на оборотите на празния ход
- За техническо обслужване на искрогасителната мрежа
- Техническо обслужване на запалителната свещ
- Почистване на въздушния филтър
- Заточване на веригата за моторен трион
- Смазване на режещото оборудване
- Транспортиране
- Съхранение
- Технически характеристики
- Принадлежности
- Декларация за съответствие
- Sadržaj
- Uvod
- Sigurnost
- Sastavljanje
- Rukovanje
- Održavanje
- Plan održavanja
- Svakodnevno održavanje
- Sedmično održavanje
- Mjesečno održavanje
- Godišnje održavanje
- Povremeno održavanje
- Da biste podesili brzinu u praznom hodu
- Održavanje mrežice za odvođenje iskri
- Da biste obavili radove održavanja na svjećici
- Čišćenje zračnog filtera
- Da biste naoštrili lanac pile
- Da biste podmazali opremu za rezanje
- Transport
- Skladištenje
- Tehnički podaci
- Pribor
- Izjava o usaglašenosti
- Obsah
- Úvod
- Bezpečnost
- Montáž
- Provoz
- Údržba
- Přeprava
- Skladování
- Technické údaje
- Příslušenství
- Prohlášení o shodě
- Indhold
- Indledning
- Sikkerhed
- Montering
- Drift
- Vedligeholdelse
- Vedligeholdelsesskema
- Dagligt eftersyn
- Ugentligt eftersyn
- Månedligt eftersyn
- Årlig vedligeholdelse
- Periodisk vedligeholdelse
- Sådan justerer du tomgangshastigheden
- Sådan foretager du vedligeholdelse på gnistfangernettet.
- Sådan foretager du vedligeholdelse på tændrøret
- Rengøring af luftfilteret
- Sådan skærpes savkæden
- Sådan smøres skæreudstyret
- Transport
- Opbevaring
- Tekniske data
- Tilbehør
- Overensstemmelseserklæring
- Inhalt
- Einleitung
- Sicherheit
- Montage
- Betrieb
- So verwenden Sie den Kraftstoff
- Vor dem Starten des Motors
- So starten Sie bei kaltem Motor
- So starten Sie einen warmen Motor
- So starten Sie den Motor, wenn der Kraftstoff zu heiß ist
- So stoppen Sie das Gerät
- So verwenden Sie eine Rindenstütze
- So fällen Sie einen Baum
- So entasten Sie einen Baum
- So zersägen Sie einen Baumstamm
- Wartung
- Transport
- Lagerung
- Technische Daten
- Zubehör
- Konformitätserklärung
- Περιεχόμενα
- Εισαγωγή
- Ασφάλεια
- Συναρμολόγηση
- Λειτουργία
- Συντήρηση
- Πρόγραμμα συντήρησης
- Καθημερινή συντήρηση
- Εβδομαδιαία συντήρηση
- Μηνιαία συντήρηση
- Ετήσια συντήρηση
- Διακεκομμένη συντήρηση
- Για να ρυθμίσετε τις στροφές ανά λεπτό ρελαντί
- Εκτέλεση εργασιών συντήρησης στη σίτα συγκράτησης των σπινθήρων
- Εκτέλεση εργασιών συντήρησης στο μπουζί
- Καθαρισμός του φίλτρου αέρα
- Ακόνισμα αλυσίδας πριονιού
- Λίπανση του εξοπλισμού κοπής
- Μεταφορά
- Αποθήκευση
- Τεχνικά στοιχεία
- Αξεσουάρ
- Δήλωση Συμμόρφωσης
- Contenido
- Introducción
- Seguridad
- Montaje
- Funcionamiento
- Mantenimiento
- Programa de mantenimiento
- Mantenimiento diario
- Mantenimiento semanal
- Mantenimiento mensual
- Mantenimiento anual
- Mantenimiento intermitente
- Para ajustar el régimen de ralentí
- Para realizar el mantenimiento de la red apagachispas
- Para realizar el mantenimiento de la bujía
- Para limpiar el filtro de aire
- Para afilar la cadena de sierra
- Para lubricar el equipo de corte
- Transporte
- Almacenamiento
- Datos técnicos
- Accesorios
- Declaración de conformidad
- Contenido
- Introducción
- Seguridad
- Montaje
- Funcionamiento
- Mantenimiento
- Programa de mantenimiento
- Mantenimiento diario
- Mantenimiento semanal
- Mantenimiento mensual
- Mantenimiento anual
- Mantenimiento intermitente
- Para ajustar el régimen de ralentí
- Para realizar tareas de mantenimiento en la red apagachispas
- Para realizar tareas de mantenimiento en la bujía
- Para limpiar el filtro de aire
- Para afilar la cadena de sierra
- Para lubricar el equipo de corte
- Transporte
- Almacenamiento
- Datos técnicos
- Accesorios
- Declaración de conformidad
- Sisukord
- Sissejuhatus
- Ohutus
- Kokkupanek
- Töö
- Hooldamine
- Transportimine
- Hoiustamine
- Tehnilised andmed
- Lisavarustus
- Vastavusdeklaratsioon
- Sisällys
- Johdanto
- Turvallisuus
- Asentaminen
- Käyttö
- Huolto
- Kuljettaminen
- Säilytys
- Tekniset tiedot
- Tarvikkeet
- Vaatimustenmukaisuusvakuutus
- Sommaire
- Introduction
- Sécurité
- Montage
- Utilisation
- Entretien
- Schéma d'entretien
- Entretien quotidien
- Entretien hebdomadaire
- Entretien mensuel
- Maintenance annuelle
- Entretien périodique
- Pour régler le régime de ralenti
- Pour effectuer l'entretien de la grille pare-étincelles
- Pour effectuer l’entretien de la bougie d’allumage
- Pour nettoyer le filtre à air
- Pour affûter la chaîne de sciage
- Pour lubrifier l’équipement de coupe
- Transport
- Remisage
- Caractéristiques techniques
- Accessoires
- Déclaration de conformité
- Sadržaj
- Uvod
- Sigurnost
- Sastavljanje
- Rad
- Održavanje
- Prijevoz
- Skladištenje
- Tehnički podaci
- Dodaci
- Izjava o sukladnosti
- TARTALOMJEGYZÉK
- Bevezető
- Biztonság
- Összeszerelés
- Üzemeltetés
- Karbantartás
- Szállítás
- Tárolás
- Műszaki adatok
- Tartozékok
- Megfelelőségi nyilatkozat
- Sommario
- Introduzione
- Sicurezza
- Definizioni di sicurezza
- Istruzioni di sicurezza generali
- Istruzioni di sicurezza per l’utilizzo
- Istruzioni di sicurezza per la manutenzione
- Montaggio
- Utilizzo
- Manutenzione
- Programma di manutenzione
- Manutenzione giornaliera
- Manutenzione settimanale
- Manutenzione mensile
- Manutenzione annuale
- Manutenzione occasionale
- Per regolare il regime minimo
- Per gli interventi di manutenzione della rete parascintille
- Per gli interventi di manutenzione della candela
- Per pulire il filtro dell'aria
- Per affilare la catena
- Per lubrificare l'attrezzatura di taglio
- Trasporto
- Rimessaggio
- Dati tecnici
- Accessori
- Dichiarazione di conformità
- 目次
- はじめに
- 安全性
- 組立
- 操作
- メンテナンス
- 搬送
- 保管
- 主要諸元
- アクセサリー
- 適合宣言
- TURINYS
- Įvadas
- Sauga
- Surinkimas
- Naudojimas
- Techninės priežiūros darbas
- Priežiūros grafikas
- Kasdienė techninė priežiūra
- Savaitinė techninė priežiūra
- Mėnesinė techninė priežiūra
- Kasmetinė techninė priežiūra
- Protarpiais atliekama techninė priežiūra
- Greičio tuščiąja eiga reguliavimas
- Kibirkščių sulaikymo tinklelio priežiūra
- Uždegimo žvakės priežiūra
- Kaip išvalyti oro filtrą
- Pjūklo grandinės galandimas
- Pjovimo įrangos tepimas
- Transportavimas
- Laikymas
- Techniniai duomenys
- Priedai
- Atitikties deklaracija
- Saturs
- Ievads
- Drošība
- Montāža
- Lietošana
- Apkope
- Transportēšana
- Glabāšana
- Tehniskie dati
- Piederumi
- Atbilstības deklarācija
- Inhoud
- Inleiding
- Veiligheid
- Montage
- Werking
- Onderhoud
- Transport
- Opslag
- Technische gegevens
- Accessoires
- Verklaring van overeenstemming
- INNHOLD
- Innledning
- Sikkerhet
- Montering
- Bruk
- Vedlikehold
- Transport
- Oppbevaring
- Tekniske data
- Tilbehør
- Samsvarserklæring
- SPIS TREŚCI
- Wstęp
- Bezpieczeństwo
- Montaż
- Obsługa
- Przegląd
- Transport
- Przechowywanie
- Dane techniczne
- Akcesoria
- Deklaracja zgodności
- ÍNDICE
- Introdução
- Segurança
- Montagem
- Funcionamento
- Manutenção
- Esquema de manutenção
- Controle diário
- Controle semanal
- Manutenção mensal
- Manutenção anual
- Manutenção intermitente
- Ajustar o ralenti
- Realizar tarefas de manutenção na rede retentora de faíscas
- Para efetuar a manutenção da vela de ignição
- Para limpar o filtro de ar
- Para afiar a corrente da serra
- Para lubrificar o equipamento de corte
- Transporte
- Armazenamento
- Especificações técnicas
- Acessórios
- Declaração de conformidade
- Conteúdo
- Introdução
- Segurança
- Montagem
- OPERAÇÃO
- Para usar o combustível
- Antes de dar partida no motor
- Para dar partida a frio em um motor
- Para dar partida a quente em um motor
- Para dar partida no motor quando o combustível estiver muito quente
- Para interromper o funcionamento
- Usar a ponta de batente
- Para derrubar uma árvore
- Para cortar um galho de uma árvore
- Para cortar um tronco
- Manutenção
- Cronograma de manutenção
- Manutenção diária
- Manutenção semanal
- Manutenção mensal
- Manutenção anual
- Manutenção Intermitente
- Para ajustar a marcha lenta
- To do maintenance on the spark arrester mesh
- Para fazer manutenção na vela de ignição
- Para limpar o filtro de ar
- Para afiar a corrente da serra
- Para lubrificar o equipamento de corte
- Transporte
- Armazenagem
- Dados técnicos
- Acessórios
- Declaração de Conformidade
- CUPRINS
- Introducere
- Siguranţă
- Definiţii privind siguranţa
- Instrucțiuni generale de siguranță
- Instrucțiuni de siguranță pentru utilizare
- Instrucțiuni de siguranță pentru întreținere
- Asamblarea
- Funcționarea
- Pentru utilizarea carburantului
- Înainte de pornirea motorului
- Pentru pornirea unui motor rece
- Pentru pornirea unui motor cald
- Pentru a porni motorul când carburantul este prea fierbinte
- Pentru oprire
- Utilizarea unei bare de protecție
- Pentru a doborî un copac
- Tăierea ramurilor unui arbore
- Ferăstruirea unui buștean
- Întreținerea
- Program de întreţinere
- Întreținerea zilnică
- Întreținerea săptămânală
- Întreținerea lunară
- Întreținerea anuală
- Întreţinere intermitentă
- Pentru reglarea turaţiei de mers în gol
- Pentru a efectua operații de întreținere la sita parascântei
- Pentru a efectua operații de întreținere a bujiei
- Pentru a curăța filtrul de aer
- Pentru ascuţirea lanţului de ferăstrău
- Pentru a unge echipamentul de tăiere
- Transportul
- Depozitarea
- Date tehnice
- Accesorii
- Declarație de conformitate
- Содержание
- Введение
- Безопасность
- Сборка
- Эксплуатация
- Техническое обслуживание
- График технического обслуживания
- Ежедневное обслуживание
- Еженедельное обслуживание
- Ежемесячное обслуживание
- Ежегодное обслуживание
- Периодическое обслуживание
- Регулировка скорости холостого хода
- Техобслуживание искрогасительной сетки
- Техобслуживание свечи зажигания
- Очистка воздушного фильтра
- Заточка цепи пилы
- Смазка режущего оборудования
- Транспортировка
- Хранение
- Технические данные
- Принадлежности
- Декларация о соответствии
- Obsah
- Úvod
- Bezpečnosť
- Montáž
- Prevádzka
- Údržba
- Preprava
- Skladovanie
- Technické údaje
- Príslušenstvo
- Vyhlásenie o zhode
- VSEBINA
- Uvod
- Varnost
- Montaža
- Delovanje
- Vzdrževanje
- Prevoz
- Shranjevanje
- Tehnični podatki
- Dodatna oprema
- Izjava o skladnosti
- Sadržaj
- Uvod
- Bezbednost
- Sklapanje
- Rukovanje
- Održavanje
- Transport
- Skladištenje
- Tehnički podaci
- Oprema
- Deklaracija o usaglašenosti
- Innehåll
- Introduktion
- Säkerhet
- Montering
- Drift
- underhåll
- Transport
- Förvaring
- Tekniska data
- Tillbehör
- Försäkran om överensstämmelse
- İçindekiler
- Giriş
- Güvenlik
- Montaj
- Kullanım
- Bakım
- Taşıma
- Saklama
- Teknik veriler
- Aksesuarlar
- Uyumluluk Bildirimi
- Зміст
- Вступ
- Безпека
- Збирання
- Експлуатація
- Технічне обслуговування
- Графік технічного обслуговування
- Щоденне технічне обслуговування
- Щотижневе технічне обслуговування
- Щомісячне технічне обслуговування
- Щорічне обслуговування
- Періодичне технічне обслуговування
- Налаштування швидкості холостого ходу
- Технічне обслуговування іскропоглинальної сітки
- Технічне обслуговування свічки запалювання
- Очищення повітряного фільтра
- Нагострювання ланцюга пилки
- Змащування різального обладнання
- Транспортування
- Зберігання
- Технічні характеристики
- Аксесуари
- Декларація відповідності
To adjust the idle speed
Make sure that the air filter is clean and the air filter
cover is attached before you adjust the idle speed.
1. Turn the idle adjustment screw, which is identified
with a "T" mark, clockwise until the saw chain starts
to turn.
2. Turn the idle adjustment screw, which is identified
with a "T" mark, counterclockwise until the saw chain
stops.
3. The idle speed must be below the speed when the
saw chain starts to turn. The idle speed is correct
when the engine operates smoothly in all positions.
To do maintenance on the spark
arrester mesh
• Use a wire brush to clean the spark arrester mesh.
(Fig. 57)
To do maintenance on the spark plug
CAUTION: Use the recommended
spark plug. Make sure that the replacement
is the same as the manufacturer supplied
part. An incorrect spark plug can cause
damage to the product.
1. If the product is hard to start or operate, examine
the spark plug for unwanted materials. To decrease
the risk of unwanted material on the spark plug
electrodes:
a) make sure that the idle speed is correctly
adjusted.
b) make sure that the fuel mixture is correct.
c) make sure that the air filter is clean.
2. Clean the spark plug if it is dirty. Make sure that the
electrode gap is correct. (Fig. 59)
3. Replace the spark plug when it is necessary.
To clean the air filter
1. Remove the air filter cover and remove the air filter.
(Fig. 60)
2. Clean the air filter with warm soap water. Make sure
that the air filter is dry before you install it.
3. Replace the air filter if it is too dirty to fully clean it.
Always replace a damaged air filter.
To sharpen the saw chain
The cutter
The cutting part of the saw chain is called the cutter and
consists of a cutting tooth (A) and the depth gauge (B).
The cutters cutting depth is determined by the difference
in height between the two, the depth gauge setting (C).
(Fig. 61)
When you sharpen a cutting tooth there are four
important factors to remember:
• Filing angle.
(Fig. 62)
• Cutting angle.
(Fig. 63)
• File position.
(Fig. 64)
• Round file diameter.
(Fig. 65)
To sharpen the cutting teeth
Use a round file and a file gauge to sharpen the cutting
teeth. See
Saw chain filing and saw chain combinations
on page 22
for information on the recommended
dimension of the file and gauge for the saw chain
installed on your product.
(Fig. 66)
1. Make sure that the saw chain has the correct
tension. A chain without the correct tension moves
to one side does and not sharpen correctly.
2. Use the file on all the teeth on one side. Then use
the file on the cutting teeth from the inner face and
decrease the pressure in the reverse direction.
3. Turn the product on the opposite side and use the
file on the teeth.
4. Use the file to keep all teeth the same length.
Replace a worn saw chain when the length of the
cutting teeth decreases to 4 mm (5/32 in).
To adjust the depth gauge setting
Sharpen the cutting teeth before you adjust the depth
gauge setting. See
To sharpen the cutting teeth on page
19
. When you sharpen the cutting tooth (A), the depth
gauge setting (C) will decrease. To maintain optimal
cutting performance, the depth gauge (B) has to be filed
down to achieve the recommended depth gauge setting.
See
Saw chain filing and saw chain combinations on
page 22
to find the correct depth gauge setting for your
particular chain.
(Fig. 67)
(Fig. 68)
Note: This recommendation assumes that the length
of the cutting teeth is not reduced excessively.
Use a flat file and depth gauge tool to adjust the depth
gauge.
1. Put the depth gauge tool above the saw chain.
Detailed information regarding how to use the depth
gauge tool will be found on the package of the depth
gauge tool.
862 - 003 - 09.07.2022
19