User's Manual

9
OPERATING YOUR UNIT
W ARNING:
The chain must not move
when the engine runs at idle speed . If the chain
moves at idle speed refer to CARBURETOR
ADJUSTMENT with in th is manual. Avo id con-
tact with the muffler . A hot muffler can cause
serious burns.
To stop the engine move the switch to the
STOP position.
To start the engine hold the saw firmly on
the ground as illustrated below. Make sure
the chain is free to turn without contacting
any object.
Hold saw firmly while pulling starter rope.
Use only 15”--18” of rope per pull.
Important points to remember
Wh en pu lling thestarterrope, d ono tuse th efu ll
extent of the rope as this can cause the rope to
break. Do not let starter rope snap back. Hold
the handle and let the rope rewind slowly .
For cold weather starting, start the unit at full
choke; allow the engine to warm up before
squeezing the throttle trigger.
NOTE:
Do not cut material with the choke/
fast idle lever at the FULL CHOKE position.
STARTING A COLD ENGINE (or a
wa rm engi ne after running out of
fuel)
NOTE
: In the following steps, when the cho-
ke /fast idle le ver is pu lled o ut to the full e xt en t,
the correct throttle setting for starting is set au-
t oma t ically .
1. Move ON/STOP switch to the ON position.
2. Pull thechoke/fast idle lever outto thefull
extent.
3. Pull starter rope quickly with your right
handa maximum of 10 times. Then, pro-
ceed to the next step.
NOTE:
If the engine sounds as if it is trying
to start before the 10th pull, stop pulling and
immediately proceed to the next step.
4. Push the choke/fast idle lever in com-
pletely (to the OFF CHOKE position).
5. Pull the starter rope quickly with your
right hand until the engine starts.
6. Allow the engine to run for approximately
5 seconds. Then, squeeze and release
throttle triggerto allow engineto returnto
idle speed.
ON/ST OP SWITCH
CHOKE/FAST IDLE LEVER
FULL OFF
STARTING A WARM ENGINE
1. Move ON/STOP switch to the ON position.
2. Pull thechoke/fast idle lever out to the full
extent; then, push the choke/fast idle
lever in completely (to the OFF CHOKE
position).
3. Pull the starter rope quickly with your
right hand until the engine starts.
4. Squeeze and release throttle trigger to
allow engine to return to idle speed.
DIFFICULT STARTING (or starting a
flooded engine)
The engine may be flooded with too much
fuel if it has not started after 10 pulls.
Flooded engines can be cleared of excess
fuel by following the warm engine starting
procedure listed above. Insure the ON/
STOP switch is in the ON position.
Starting could require pulling the starterrope
handle many times dependingon how badly
the unit is flooded. If engine fails to start refer
to the TROUBLESHOOTING TABLE.
CHAIN BRAKE
WARNING:
If the brake band is worn
too thin it may break when the chain brake is
trigge red. With a broken brake band, the chain
brake will not stop the chain. The chain brake
should be replaced by an auth orized service
dealer if any part is worn to less than 0.020!
(0.5 mm) thick. Repairs on a chain brake
should be made by an authorized service deal-
er . Take your unit to the place of purchase if
purchased from a servicing dealer , or to the
nearest authorized Husqvarna Ser vice Deale r.
S This saw is equipped with a chain brake.
The brake is designed to stop the chain if
kickback occurs.
S The inertia--activated chain brake is
activated if the front hand guard is pushed
forward, either manually (by hand) or
automatically (by sudden movement).
S If the brake is already activated, it is
disengagedby pulling thefronthandguard
back toward the front handle as far as
possible.