User guide
Table Of Contents
- Symbols
- Contents
- Note the following before starting:
- Dear Customer,
- Important
- Personal protective equipment
- Machine¢s safety equipment
- Fitting the handle
- Fitting the auger
- Fuel safety
- Fuel
- Fuelling
- Check before starting
- Starting and stopping
- General working instructions
- Carburettor
- Muffler
- Cooling system
- Air filter
- Gear
- Fuel filter
- Spark plug
- Maintenance schedule
- Technical data
- Símbolos
- Índice
- Antes de arrancar, observe lo siguiente:
- Apreciado cliente:
- Importante
- Equipo de protección personal
- Equipo de seguridad de la máquina
- Montaje de la empuñadura
- Montaje de la barrena
- Seguridad en el uso del combustible
- Carburante
- Repostaje
- Control antes de arrancar
- Arranque y parada
- Instrucciones generales de trabajo
- Carburador
- Silenciador
- Sistema refrigerante
- Filtro de aire
- Engranaje
- Filtro de combustible
- Bujía
- Programa de mantenimiento
- Datos técnicos
- Símbolos
- Índice
- Antes de arrancar, observe o seguinte:
- Prezado cliente!
- Importante
- Equipamento de protecção pessoal
- Equipamento de segurança da máquina
- Montagem do punho
- Encaixar o perfurador
- Segurança no manejo de combustível
- Combustível
- Abastecimento
- Controlo antes de arrancar
- Arranque e paragem
- Instruções gerais de trabalho
- Carburador
- Silenciador
- Sistema de arrefecimento
- Filtro de ar
- Engrenagem
- Filtro de combustível
- Vela de ignição
- Esquema de manutenção
- Especificações técnicas
- ìÒÎÓ‚Ì˚ ӷÓÁ̇˜ÂÌËfl
- ëÓ‰ÂðʇÌËÂ
- èÂð‰ Á‡ÔÛÒÍÓÏ ÔðÓÒΉËÚ Á‡ ÒÎÂ‰Û˛˘ËÏ:
- 삇ʇÂÏ˚È ÔÓÍÛÔ‡ÚÂθ!
- LJÊ̇fl ËÌÙÓðχˆËfl
- ëð‰ÒÚ‚‡ Á‡˘ËÚ˚ ÓÔÂð‡ÚÓð‡
- ìÒÚðÓÈÒÚ‚‡ ·ÂÁÓÔ‡ÒÌÓÒÚË Ï‡¯ËÌ˚
- åÓÌÚ‡Ê ðÛÍÓflÚÍË
- ìÒÚ‡Ìӂ͇ ·Óð‡
- èð‡‚Ë· ·ÂÁÓÔ‡ÒÌÓÒÚË ÔðË Á‡Ôð‡‚ÍÂ
- èÓ‰„ÓÚӂ͇ ÚÓÔÎË‚ÌÓÈ ÒÏÂÒË
- á‡Ôð‡‚͇
- èðÓ‚Âð͇ ÔÂð‰ ÔÛÒÍÓÏ
- á‡ÔÛÒÍ Ë ÓÒÚ‡Ìӂ͇
- 鷢ˠð‡·Ó˜Ë ËÌÒÚðÛ͈ËË
- ä‡ð·˛ð‡ÚÓð
- ÉÎÛ¯ËÚÂθ
- ëËÒÚÂχ Óı·ʉÂÌËfl
- ÇÓÁ‰Û¯Ì˚È ÙËθÚð
- èÂð‰‡˜‡
- íÓÔÎË‚Ì˚È ÙËθÚð
- 나‡ Á‡ÊË„‡ÌËfl
- Éð‡ÙËÍ ÚÂıÌ˘ÂÒÍÓ„Ó Ó·ÒÎÛÊË‚‡ÌËfl
- íÂıÌ˘ÂÒÍË ı‡ð‡ÍÚÂðËÒÚËÍË
![](/manual/husqvarna/143ae15/user-guide/images/img-14.png)
WORKING TECHNIQUES
14 – English
General working instructions
Safety instructions regarding the
surroundings
• Never allow children to use the machine.
• Ensure that no-one comes closer than 5 m while you
are working.
• Never allow anyone else to use the machine without
first ensuring that they have understood the contents
of the operator’s manual.
Safety instructions while working
• Always ensure you have a safe and stable working
position.
• Always hold the machine with both hands.
• Use your right hand to control the throttle setting.
• Make sure that your hands and feet do not come near
the cutting attachment when the engine is running.
• Start drilling with half-throttle, and gradually increase
the engine speed so that the drill may get into the
ground smoothly.
• If the drill has been caught in the ground and cannot
be pulled out, stop the engine and rotate the auger
counter-clockwise.
• Always turn off the engine when you have finished
drilling.
• When the engine is switched off, keep your hands and
feet away from the cutting attachment until it has
stopped completely.
• If any foreign object is hit or if vibrations occur stop the
machine immediately. Disconnect the HT lead from
the spark plug. Check that the machine is not
damaged. Repair any damage.
IMPORTANT!
This section takes up the basic safety precautions for
working with an earth auger.
If you encounter a situation where you are uncertain
how to proceed you should ask an expert. Contact your
dealer or your service workshop.
Avoid all usage which you consider to be beyond your
capability.
!
WARNING! The machine can cause
serious personal injury. Read the safety
instructions carefully. Learn how to use
the machine.
!
WARNING! Cutting tool. Do not touch the
tool without first switching off the
engine.
!
WARNING! Drilling into or contact with
electrical cables or wires can lead to
death or serious bodily injury. The
machine is not electrically insulated. To
reduce the risk of electrocution, always
check for underground pipes, cables and
wires before drilling. Contact your local
utility company or locator service for
information regarding cable and pipe
locations. If necessary, confirm the
actual locations by use of devices such
as cable detectors and by carefully
digging trenches.
!
WARNING! Striking something hard in
the earth, such as rocks or tree roots,
may cause the drill to come to a sudden
stop. This can lead to a reacting motion
on the auger, which can cause the
operator to lose control of the machine
or throw him to the ground, resulting in
serious injury. To reduce the risk of
injury, always hold the auger securely to
control such motion.
H1152440-10,143AE15.fm Page 14 Wednesday, October 28, 2009 11:19 AM