Operator’s manual WARNING Before using our products, please read this manual carefully to understand the proper use of your unit.
English EC-declaration of conformity Applies to Europe only We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare under sole responsibility that the hedge trimmers Husqvarna 226HD60S and 226HD75S with serial numbers dating from 2008 onwards (the year is clearly stated on the rating plate, followed by the serial number), comply with the requirements of the COUNCIL'S DIRECTIVE • of June 22, 1998 ”relating to machinery” 98/37/EC, annex IIA.
English Contents Symbols on the machine ••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• 5 Introduction ••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• 5 DEAR CUSTOMER! ••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• 5 Safety ••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• 6 SAFETY FIRST ••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
English Symbols on the machine For safe operation and maintenance, symbols are carved in relief on the machine. According to these indications, please be careful not to take a mistake.
English Safety WARNINGS IN THE MANUAL SAFETY FIRST WARNING Instructions contained in warnings within this manual and warning seals marked with a symbol on the blower concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail.
English What is what? 23 3 20 21 22 2 4 5 6 7 13 8 19 12 10 9 18 15 1 24 11 16 17 14 WHAT IS WHAT? 1 Operator’s manual 13 Choke lever 2 Grease nipple 14 Throttle lever 3 Gear case 15 Safety lock lever 4 Blades 16 Locking lever 5 Blade guard 17 Rear handle 6 Hand guard 18 Stop switch 7 Front handle 19 Air filter cover 8 Engine cover (cylinder cover) 20 Socket 9 Starter handle 21 Allen key 10 Fuel cap 22 Spanner 11 Fuel tank 23 Transport guard 12 Primer pump 24 Spark plug
English Technical data TECHNICAL DATA 226HD60S 226HD75S Air-cooled 2-stroke gasoline 23.6 34 26 3000±200 0.85/8000 Air-cooled 2-stroke gasoline 23.6 34 26 3000±200 0.85/8000 NGK CMR7H 0.6-0.7 NGK CMR7H 0.6-0.7 Mixture (Gasoline 50 : Oil 1) 0.47 Walbro Diaphragm type Mixture (Gasoline 50 : Oil 1) 0.47 Walbro Diaphragm type Double-sided blades 600 35 Centrifugal clutch. Cam-crank 5.11 Double-sided blades 750 35 Centrifugal clutch. Cam-crank 5.11 Weight Weight without fuel and grease, kg 5.8 6.
English For safe operation NOTE THE FOLLOWING BEFORE STARTING; IMPORTANT 1. THIS MACHINE CAN CAUSE SERIOUS INJURIES. Read this manual carefully until you completely understand and follow all safety and operating instructions. Also, know how to stop the machine quickly in an emergency. 2. Keep this manual handy so that you may refer to it later whenever any questions arise. Also note, if you have any questions which cannot be answered herein, contact the dealer from whom you purchased the product. 3.
English For safe operation WORKING PLAN STARTING THE ENGINE 1. You should never use the product when under the influence of alcohol, when suffering from exhaustion or lack of sleep, when suffering from drowsiness as a result of having taken cold medicine or at any other time when a possibility exists that your judgment might be impaired or that you might not be able to operate the product properly and in a safe manner. 2. When planning your work schedule, allow plenty of time to rest.
English For safe operation IF SOMEONE COMES HANDLING FUEL 1. Guard against hazardous situations at all times. Warn adults to keep pets and children away from the area. Be careful if you are approached. Injury may result from flying debris. 2. If someone calls out or otherwise interrupts you while working, always be sure to turn off the engine before turning around. 1. The engine of the Husqvarna product is designed to run on a mixed fuel, which contains highly flammable gasoline.
English Fuel HOW TO MIX FUEL WARNING • Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground for fueling and move at least 3m (10ft) away from the fueling point before starting the engine. IMPORTANT Pay attention to agitation. • The Husqvarna engines are lubricated by oil specially formulated for air-cooled 2-cycle gasoline engine use.
English Operation STARTING ENGINE IMPORTANT 1. Feed fuel into the fuel tank and tighten the cap securely. 2. Rest the unit on a flat, firm place. Keep the cutting head off the ground and clear of surrounding objects as it will start moving upon starting of the engine. 3. Push the primer pump several times until overflown fuel flows out in the clear tube. (1) Primer pump (1) 4. When the engine is cool, move the choke lever to the closed position.
English Operation ADJUSTING IDLING SPEED HEDGE TRIMMING TECHNIQUES • Before adjusting the carburetor, clean the air filter and warm up the engine. (1) Trim sides of a hedge first, and then the top. Vertical cut: • With the double-sided blade hedge-trimmer, model 226HD60S/226HD75S use an arcing cut from the bottom upwards, then downwards to use both sides of the blades. (1) Air filter element • Idle screw is adjusted in order to ensure a good safety margin between idle running and clutch engagement.
English Maintenance Maintenance, replacement, or repair of the emission control device and systems may be performed by any non-road engine repair establishment or individual.
English Maintenance INTAKE AIR COOLING VENT WARNING • Never touch the cylinder, muffler, or spark plugs with your bare hands immediately after stopping the engine. The engine can become very hot when in operation, and doing so could result in severe burns. • Clean the cylinder fins with compressed air or a brush. Check the cutting edges and reform with a flat file. Point : 1. Keep the end corner sharp. 2. Round the root of the edge. 3. Do not use water when using a grinder.
English Maintenance SAFETY LOCK • Stop operation when the safety lock is defective. • Safety lock is the device not to accelerate the throttle lever without intention. While pushing the safety lock, you can accelerate the throttle lever. (1) (1) Safety lever 1. Check if the throttle lever does not move when you do not push the safety lock. 2. Check if the throttle lever moves when you grasp or release it while pushing the safety lock. 3.
English Storage 1. 2. 3. 4. 5. 6. Lubricate the blade bars to prevent rust with special grease, part no. 531 00 75-12 (UL21), before long periods of storage. Empty the fuel tank and put the cap back on. Remove the spark plug, pour a small amount of oil into the cylinder. Rotate the crankshaft several times using the starting rope in order to distribute the oil. Put the spark plug back in. Wrap the engine with a plastic sheet.
