Operators Manual
Table Of Contents
- Symbols
- Contents
- Note the following before starting:
- Dear Customer,
- Important
- Personal protective equipment
- Machine¢s safety equipment
- Fitting the gearbox
- Assembly the cutting equipment without the hook
- Assembly the hook together with the cutting equipment
- Fitting the engine stand
- Telescopic function
- Fuel safety
- Fuel
- Fueling
- Check before starting
- Starting and stopping
- General working instructions
- Carburettor
- Muffler
- Cooling system
- Spark plug
- Air filter
- Fuel filter
- Gear
- Guide sleeve and oil seal on gearbox
- Vibrations
- Maintenance schedule
- Technical data
- Símbolos
- Índice
- Antes de arrancar, observe o seguinte:
- Prezado cliente!
- Importante
- Equipamento de protecção pessoal
- Equipamento de segurança da máquina
- Montagem da caixa de velocidades
- Montagem do equipamento de corte sem o gancho
- Montagem do gancho juntamente com o equipamento de corte
- Montagem do suporte do motor
- Função telescópica
- Segurança no manejo de combustível
- Combustível
- Abastecimento
- Controlo antes de arrancar
- Arranque e paragem
- Instruções gerais de trabalho
- Carburador
- Silenciador
- Sistema de arrefecimento
- Vela de ignição
- Filtro de ar
- Filtro de combustível
- Engrenagem
- Manga de guia e vedante do óleo na caixa de velocidades
- Vibrações
- Esquema de manutenção
- Especificações técnicas
- Simbol-simbol
- Kandungan
- Ingat perkara-perkara berikut sebelum menghidupkan:
- Pelanggan yang budiman,
- Penting
- Kelengkapan pelindung peribadi
- Kelengkapan keselamatan mesin
- Memasang kotak gear
- Pasang kelengkapan pemotong tanpa cangkuk
- Pasang cangkuk bersama dengan kelengkapan pemotong
- Memasang dirian enjin
- Fungsi teleskopik
- Keselamatan bahan bakar
- Bahan bakar
- Mengisi bahan bakar
- Periksa sebelum menghidupkannya
- Menghidupkan dan Mematikan enjin
- Arahan kerja am
- Karburetor
- Peredam bunyi
- Sistem penyejuk
- Palam pencucuh
- Penapis udara
- Penapis bahan bakar
- Gear
- Sarung panduan dan kedap minyak pada kotak gear
- Getaran
- Jadual penyengggaraan
- Data teknikal
ASSEMBLY
10 – English
Fitting the gearbox
• Loosen the screws on the gear box.
• Clean the shaft from grease or dust before assembly
the gearbox.
• Assemble the gearbox onto the shaft. Make sure that
the gearbox is pushed to the arrow on the shaft.
• Make sure that the screw on the gear box align with
the hole on the shaft.
• Tighten the screw on the gear box in the hole on the
shaft.
CAUTION! Make sure that the drive shaft inside the shaft
engages with the cut-out in the cutting head.
Assembly the cutting equipment
without the hook
• Use the shorter screws, spring washers, flat washers
and nylon lock hex nut together with the cutter.
• Assembly the screws, spring washer, the cutter, the
washer and the nut, according to the illustration.
• Assembly the cutter with the two srews.
Assembly the hook together with
the cutting equipment
• Use the longer screws, spring washer, flat washer and
the nylon lock hex nut together with the cutter and the
hook.
H1157097-38,226PTC6,PD3.fm Page 10 Monday, April 18, 2016 8:08 AM