Operators Manual
Table Of Contents
- Symbols
- Contents
- Note the following before starting:
- Dear Customer,
- Important
- Personal protective equipment
- Machine¢s safety equipment
- Fitting the gearbox
- Assembly the cutting equipment without the hook
- Assembly the hook together with the cutting equipment
- Fitting the engine stand
- Telescopic function
- Fuel safety
- Fuel
- Fueling
- Check before starting
- Starting and stopping
- General working instructions
- Carburettor
- Muffler
- Cooling system
- Spark plug
- Air filter
- Fuel filter
- Gear
- Guide sleeve and oil seal on gearbox
- Vibrations
- Maintenance schedule
- Technical data
- Símbolos
- Índice
- Antes de arrancar, observe o seguinte:
- Prezado cliente!
- Importante
- Equipamento de protecção pessoal
- Equipamento de segurança da máquina
- Montagem da caixa de velocidades
- Montagem do equipamento de corte sem o gancho
- Montagem do gancho juntamente com o equipamento de corte
- Montagem do suporte do motor
- Função telescópica
- Segurança no manejo de combustível
- Combustível
- Abastecimento
- Controlo antes de arrancar
- Arranque e paragem
- Instruções gerais de trabalho
- Carburador
- Silenciador
- Sistema de arrefecimento
- Vela de ignição
- Filtro de ar
- Filtro de combustível
- Engrenagem
- Manga de guia e vedante do óleo na caixa de velocidades
- Vibrações
- Esquema de manutenção
- Especificações técnicas
- Simbol-simbol
- Kandungan
- Ingat perkara-perkara berikut sebelum menghidupkan:
- Pelanggan yang budiman,
- Penting
- Kelengkapan pelindung peribadi
- Kelengkapan keselamatan mesin
- Memasang kotak gear
- Pasang kelengkapan pemotong tanpa cangkuk
- Pasang cangkuk bersama dengan kelengkapan pemotong
- Memasang dirian enjin
- Fungsi teleskopik
- Keselamatan bahan bakar
- Bahan bakar
- Mengisi bahan bakar
- Periksa sebelum menghidupkannya
- Menghidupkan dan Mematikan enjin
- Arahan kerja am
- Karburetor
- Peredam bunyi
- Sistem penyejuk
- Palam pencucuh
- Penapis udara
- Penapis bahan bakar
- Gear
- Sarung panduan dan kedap minyak pada kotak gear
- Getaran
- Jadual penyengggaraan
- Data teknikal
FUEL HANDLING
English – 13
Mixing
• Always mix the petrol and oil in a clean container
intended for fuel.
• Always start by filling half the amount of the petrol to
be used. Then add the entire amount of oil. Mix
(shake) the fuel mixture. Add the remaining amount of
petrol.
• Mix (shake) the fuel mixture thoroughly before filling
the machine’s fuel tank.
• Do not mix more than one month’s supply of fuel at a
time.
• If the machine is not used for some time the fuel tank
should be emptied and cleaned.
Fueling
• Always use a fuel container with an anti-spill valve.
• If you have spilled fuel on it. Wipe off the spillage and
allow remaining fuel to evaporate.
• Clean the area around the fuel cap. Contamination in
the tank can cause operating problems.
• Ensure that the fuel is well mixed by shaking the
container before filling the tank.
Petrol, litre Two-stroke oil, litre
2% (1:50) 3% (1:33)
5 0,10 0,15
10 0,20 0,30
15 0,30 0,45
20 0,40 0,60
!
WARNING! The catalytic converter
muffler gets very hot during and after
use. This also applies during idling. Be
aware of the fire hazard, especially when
working near flammable substances and/
or vapours.
!
WARNING! Taking the following
precautions, will lessen the risk of fire:
Mix and pour fuel outdoors, where there
are no sparks or flames.
Do not smoke or place hot objects near
fuel.
Always shut off the engine before
refuelling.
Always stop the engine and let it cool for
a few minutes before refuelling. Refuel in
a well ventilated area. Never fuel the
machine indoors.
When refuelling, open the fuel cap slowly
so that any excess pressure is released
gently.
Tighten the fuel cap carefully after
refuelling.
Always move the machine away from the
refuelling area and source before
starting.
H1157097-38,226PTC6,PD3.fm Page 13 Monday, April 18, 2016 8:08 AM