Operators Manual
Table Of Contents
- Symbols
- Contents
- Note the following before starting:
- Dear Customer,
- Important
- Personal protective equipment
- Machine¢s safety equipment
- Fitting the gearbox
- Assembly the cutting equipment without the hook
- Assembly the hook together with the cutting equipment
- Fitting the engine stand
- Telescopic function
- Fuel safety
- Fuel
- Fueling
- Check before starting
- Starting and stopping
- General working instructions
- Carburettor
- Muffler
- Cooling system
- Spark plug
- Air filter
- Fuel filter
- Gear
- Guide sleeve and oil seal on gearbox
- Vibrations
- Maintenance schedule
- Technical data
- Símbolos
- Índice
- Antes de arrancar, observe o seguinte:
- Prezado cliente!
- Importante
- Equipamento de protecção pessoal
- Equipamento de segurança da máquina
- Montagem da caixa de velocidades
- Montagem do equipamento de corte sem o gancho
- Montagem do gancho juntamente com o equipamento de corte
- Montagem do suporte do motor
- Função telescópica
- Segurança no manejo de combustível
- Combustível
- Abastecimento
- Controlo antes de arrancar
- Arranque e paragem
- Instruções gerais de trabalho
- Carburador
- Silenciador
- Sistema de arrefecimento
- Vela de ignição
- Filtro de ar
- Filtro de combustível
- Engrenagem
- Manga de guia e vedante do óleo na caixa de velocidades
- Vibrações
- Esquema de manutenção
- Especificações técnicas
- Simbol-simbol
- Kandungan
- Ingat perkara-perkara berikut sebelum menghidupkan:
- Pelanggan yang budiman,
- Penting
- Kelengkapan pelindung peribadi
- Kelengkapan keselamatan mesin
- Memasang kotak gear
- Pasang kelengkapan pemotong tanpa cangkuk
- Pasang cangkuk bersama dengan kelengkapan pemotong
- Memasang dirian enjin
- Fungsi teleskopik
- Keselamatan bahan bakar
- Bahan bakar
- Mengisi bahan bakar
- Periksa sebelum menghidupkannya
- Menghidupkan dan Mematikan enjin
- Arahan kerja am
- Karburetor
- Peredam bunyi
- Sistem penyejuk
- Palam pencucuh
- Penapis udara
- Penapis bahan bakar
- Gear
- Sarung panduan dan kedap minyak pada kotak gear
- Getaran
- Jadual penyengggaraan
- Data teknikal
MAINTENANCE
20 – English
Carburettor
Adjustment of the idle speed
Before any adjustments are made, make sure that the air
filter is clean and the air filter cover is fitted.
Adjust the idle speed using the idle adjustment screw T, if
it is necessary to readjust. First turn the idle adjustment
screw T clockwise until the cutting attachment starts to
rotate. Then turn the screw counter clockwise until the
cutting attachment stops. The idle speed is correctly
adjusted when the engine will run smoothly in every
position. The idle speed should also be well below the
speed at which the cutting attachment starts to rotate.
Recommended idle speed: See the Technical data
section.
Muffler
The muffler is designed to reduce the noise level and to
direct the exhaust gases away from the operator. The
exhaust gases are hot and can contain sparks, which may
cause fire if directed against dry and combustible
material.
CAUTION! Never use a machine with a defective muffler.
Cooling system
To keep the working temperature as low as possible the
machine is equipped with a cooling system.
The cooling system consists of:
1 Cooling fins on the cylinder.
2 Air intake through the crankcase (inside the tank).
Clean the cooling system with a brush once a week, more
often in demanding conditions. A dirty or blocked cooling
system results in the machine overheating which causes
damage to the piston and cylinder.
Spark plug
The spark plug condition is influenced by:
• Incorrect carburettor adjustment.
• An incorrect fuel mixture (too much or incorrect type
of oil).
• A dirty air filter.
These factors cause deposits on the spark plug
electrodes, which may result in operating problems and
starting difficulties.
If the machine is low on power, difficult to start or runs
poorly at idle speed: always check the spark plug first
before taking any further action. If the spark plug is dirty,
clean it and check that the electrode gap is 0,6-0,7 mm.
The spark plug should be replaced after about a month in
operation or earlier if necessary.
CAUTION! Always use the recommended spark plug
type! Use of the wrong spark plug can damage the piston/
cylinder. Check that the spark plug is fitted with a
suppressor.
!
WARNING! If the idle speed cannot be
adjusted so that the cutting attachment
stops, contact your dealer/service
workshop. Do not use the machine until
it has been correctly adjusted or
repaired.
T
1
2
2
H1157097-38,226PTC6,PD3.fm Page 20 Monday, April 18, 2016 8:08 AM