Operators Manual
Table Of Contents
- Dear Customer,
- Symbols on the machine:
- What is what on the chain saw? (1)
- Contents
- Before using a new chain saw
- Important
- Always use common sense (2)
- Personal protective equipment
- Machine¢s safety equipment
- Chain brake and front hand guard
- Will my hand always activate the chain brake during a kickback?
- Will my inertia activated chain brake always activate during kickback in the event of a kickback?
- Will my chain brake always protect me from injury in the event of a kickback?
- Throttle lockout
- Chain catcher
- Right hand guard
- Vibration damping system
- Stop switch
- Muffler
- Cutting equipment
- Fitting the bar and chain
- Fuel
- Fuelling
- Fuel safety
- Starting and stopping
- Before use: (33)
- General working instructions
- How to avoid kickback
- General
- Carburettor adjustment
- Checking, maintaining and servicing chain saw safety equipment
- Muffler
- Air filter
- Spark plug
- Maintenance schedule
- Technical data (P02138HV)
- Guide bar and saw chain combinations
- EC Declaration of Conformity
- Apreciado cliente:
- Símbolos en la máquina:
- ¿Qué es qué en la motosierra? (1)
- Índice
- Medidas a tomar antes de utilizar una motosierra nueva
- Importante
- Emplee siempre el sentido común. (2)
- Equipo de protección personal
- Equipo de seguridad de la máquina
- Freno de cadena con protección contra reculadas
- ¿Activará siempre mi mano el freno de cadena en caso de reculada?
- ¿Se activa siempre por inercia el freno de cadena cuando se produce una reculada?
- ¿Me protegerá siempre el freno de cadena contra daños si se produce una reculada?
- Fiador del acelerador
- Captor de cadena
- Protección de la mano derecha
- Sistema amortiguador de vibraciones
- Botón de parada
- Silenciador
- Equipo de corte
- Montaje de la espada y la cadena
- Carburante
- Repostaje
- Seguridad en el uso del combustible
- Arranque y parada
- Antes de utilizar la máquina: (33)
- Instrucciones generales de trabajo
- Medidas preventivas de las reculadas
- Generalidades
- Ajuste del carburador
- Control, mantenimiento y servicio del equipo de seguridad de la motosierra
- Silenciador
- Filtro de aire
- Bujía
- Programa de mantenimiento
- Datos técnicos (P02138HV)
- Combinaciones de espada y cadena
- Declaración CE de conformidad
- Bäste kund!
- Symboler på maskinen:
- Vad är vad på motorsågen? (1)
- Innehåll
- Åtgärder före användning av ny motorsåg
- Viktigt
- Använd alltid sunt förnuft (2)
- Personlig skyddsutrustning
- Maskinens säkerhetsutrustning
- Kedjebroms med kastskydd
- Kommer min hand alltid att aktivera kedjebromsen vid kast?
- Kommer tröghetsaktivering av kedjebromsen alltid ske om ett kast inträffar?
- Kommer kedjebromsen alltid att skydda mig från skador om ett kast inträffar?
- Gasreglagespärr
- Kedjefångare
- Högerhandsskydd
- Avvibreringssystem
- Stoppkontakt
- Ljuddämpare
- Skärutrustning
- Montering av svärd och kedja
- Drivmedel
- Tankning
- Bränslesäkerhet
- Start och stopp
- Före varje användning: (33)
- Allmänna arbetsinstruktioner
- Kastförebyggande åtgärder
- Allmänt
- Förgasarjustering
- Kontroll, underhåll och service av motorsågens säkerhetsutrustning
- Ljuddämpare
- Luftfilter
- Tändstift
- Underhållsschema
- Tekniska data (P02138HV)
- Svärd och kedjekombinationer
- EG-försäkran om överensstämmelse
- Hyvä asiakas!
- Koneessa esiintyvät tunnukset:
- Moottorisahan osat (1)
- Sisältö
- Toimenpiteet ennen uuden moottorisahan käyttöä
- Tärkeää
- Käytä aina tervettä järkeä (2)
- Henkilökohtainen suojavarustus
- Koneen turvalaitteet
- Takapotkusuojuksella varustettu ketjujarru
- Aktivoiko käteni aina ketjujarrun takapotkun yhteydessä?
- Pysäyttääkö automaattinen pysäytystoiminto ketjun aina, jos takapotku tapahtuu?
- Suojaako ketjujarru minua vahingoilta aina, jos takapotku tapahtuu?
- Kaasuliipasimen varmistin
- Ketjusieppo
- Rystyssuojus
- Tärinänvaimennus
- Pysäytin
- Äänenvaimennin
- Terälaite
- Terälevyn ja ketjun asennus
- Polttoaine
- Tankkaus
- Polttoaineturvallisuus
- Käynnistys ja pysäytys
- Aina ennen käyttöä: (33)
- Yleiset työohjeet
- Takapotkua ehkäisevät toimenpiteet
- Yleistä
- Kaasuttimen säätö
- Moottorisahan turvalaitteiden tarkastus, kunnossapito ja huolto
- Äänenvaimennin
- Ilmansuodatin
- Sytytystulppa
- Huoltokaavio
- Tekniset tiedot (P02138HV)
- Terälevy- ja ketjuyhdistelmät
- EY-vaatimustenmukaisuusvakuutus
- Til vore kunder!
- Symboler på maskinen:
- Hvad er hvad på motorsaven? (1)
- Indhold
- Forberedelser, inden en ny motorsav tages i brug
- Vigtigt
- Brug altid din sunde fornuft. (2)
- Personligt beskyttelsesudstyr
- Maskinens sikkerhedsudstyr
- Kædebremse med kastbeskyttelse
- Vil min hånd altid aktivere kædebremsen i tilfælde af kast?
- Vil træghedsaktiveringen af kædebremsen altid forekomme, hvis der indtræder et kast?
- Beskytter kædebremsen mig konstant mod skader i tilfælde af kast?
- Gasreguleringslås
- Kædefanger
- Højrehåndsbeskyttelse
- Vibrationsdæmpningssystem
- Stopkontakt
- Lyddæmper
- Skæreudstyr
- Montering af sværd og kæde
- Drivmiddel
- Tankning
- Brændstofsikkerhed
- Start og stop
- Før hver anvendelse: (33)
- Generelle arbejdsinstruktioner
- Kastforebyggende foranstaltninger
- Generelt
- Karburatorjustering
- Kontrol, vedligeholdelse og service af motorsavens sikkerhedsudstyr
- Lyddæmper
- Luftfilter
- Tændrør
- Vedligeholdelsesskema
- Tekniske data (P02138HV)
- Sværd- og kædekombinationer
- EF-overensstemmelseserklæring
- Kjære kunde
- Symboler på maskinen:
- Hva er hva på motorsagen? (1)
- Innhold
- Tiltak før bruk av en ny motorsag
- Viktig
- Bruk alltid sunn fornuft (2)
- Personlig verneutstyr
- Maskinens sikkerhetsutstyr
- Kjedebrems med kastbeskyttelse
- Vil min hånd alltid aktivere kjedebresmen ved kast?
- Vil treghetsaktivering av kjedebremsen alltid skjer hvis det inntreffer et kast?
- Vil kjedebremsen alltid beskytte meg mot skader hvis et kast inntreffer?
- Gassregulatorsperre
- Kjedefanger
- Høyrehåndsvern
- Avvibreringssystem
- Stoppbryter
- Lyddemper
- Skjæreutstyr
- Montering av sverd og kjede
- Brennstoff
- Fylling av brennstoff
- Brennstoffsikkerhet
- Start og stopp
- Før hver gangs bruk: (33)
- Generelle arbeidsinstruksjoner
- Kastforebyggende tiltak
- Generelt
- Forgasserjustering
- Kontroll, vedlikehold og service på motorsagens sikkerhetsutstyr
- Lyddemper
- Luftfilter
- Tennplugg
- Vedlikeholdsskjema
- Tekniske data (P02138HV)
- Sverd og kjedekombinasjoner
- EF-erklæring om samsvar
- Alla gentile clientela
- I simboli sulla macchina:
- Che cosa c’è nella motosega? (1)
- Indice
- Interventi prima di usare una nuova motosega
- Importante
- Impiegare sempre il buon senso. (2)
- Abbigliamento protettivo
- Dispositivi di sicurezza della macchina
- Freno della catena con protezione anticontraccolpo
- È sufficiente il contatto con la mano per attivare sempre il freno della catena in caso di sobbalzo?
- Il freno della catena è sempre attivato dalla funzione di inerzia in caso di sobbalzo?
- Il freno della catena protegge sempre l’utente da danni in caso di sobbalzo?
- Fermo del gas
- Fermo della catena
- Protezione della mano destra
- Sistema di smorzamento delle vibrazioni
- Interruttore di arresto
- Marmitta
- Attrezzatura di taglio
- Montaggio di lama e catena
- Carburante
- Rifornimento
- Carburante
- Avviamento e arresto
- Ad ogni utilizzo: (33)
- Istruzioni generali di lavoro
- Prevenzione del contraccolpo
- Generalità
- Regolazione del carburatore
- Controllo, manutenzione e servizio dei dispositivi di sicurezza della motosega
- Marmitta
- Filtro dell’aria
- Candela
- Schema di manutenzione
- Caratteristiche tecniche (P02138HV)
- Combinazioni di lama e catena
- Dichiarazione di conformità CE
- Prezado cliente!
- Símbolos na máquina:
- Como se chama, na moto-serra? (1)
- Índice
- Precauções antes de usar a nova moto-serra
- Importante
- Use sempre o seu bom senso (2)
- Equipamento de protecção pessoal
- Equipamento de segurança da máquina
- Travão de corrente com protector anti- retrocesso
- A minha mão activará sempre o travão da corrente na ocorrência de um retrocesso?
- A activação do travão da corrente por inércia funcionará sempre na ocorrência de um retrocesso?
- O travão da corrente proteger-me-á sempre de ferimentos na ocorrência de um retrocesso?
- Bloqueio do acelerador
- Retentor de corrente
- Protector da mão direita
- Sistema anti-vibração
- Contacto de paragem
- Silenciador
- Equipamento de corte
- Montagem da lâmina e corrente
- Combustível
- Abastecimento
- Segurança no manejo de combustível
- Arranque e paragem
- Sempre, antes de usar: (33)
- Instruções gerais de trabalho
- Medidas de prevenção contra retrocessos
- Noções gerais
- Afinação do carburador
- Controlo, manutenção e assistência ao equipamento de segurança da moto-serra
- Silenciador
- Filtro de ar
- Vela de ignição
- Esquema de manutenção
- Especificações técnicas (P02138HV)
- Combinações de lâmina e corrente
- Certificado CE de conformidade
- °Á·ðËÙ¤ ðÂÏ¿ÙË!
- ™‡ÌßÔÏ· ð¿Óˆ ÛÙÔ Ì˯¿ÓËÌ·:
- ÆÈ Â›Ó·È ÙÈ ÛÙÔ ·Ï˘ÛÔðÚ›ÔÓÔ; (1)
- ¶ÂÚȯfiÌÂÓ·
- ¶Ó¤ÚÁÂȘ ðÚÈÓ ı¤ÛÂÙ Û ÏÂÈÙÔ˘ÚÁ›· ¤Ó· ηÈÓÔ‡ÚÁÈÔ ðÚÈfiÓÈ
- ™ËÌ·ÓÙÈÎfi
- ÃÚËÛÈÌÔðÔț٠ð¿ÓÙÔÙ ÎÔÈÓ‹ ÏÔÁÈ΋ (2)
- °ÙÔÌÈÎfi˜ ðÚÔÛٷ٢ÙÈÎfi˜ ÂÍÔðÏÈÛÌfi˜
- ¶ÚÔÛٷ٢ÙÈÎfi˜ ÂÍÔðÏÈÛÌfi˜ ÙÔ˘ Ì˯·Ó‹Ì·ÙÔ˜
- °Ï˘ÛfiÊÚÂÓÔ Ì ðÚÔÊ˘Ï·ÎÙ‹Ú· ÙÈÓ¿ÁÌ·ÙÔ˜
- £· ÌðÔÚ› ð¿ÓÙÔÙ ÙÔ ¯¤ÚÈ ÌÔ˘ Ó· ÂÓÂÚÁÔðÔÈ› ÙÔ ÊÚ¤ÓÔ ·Ï˘Û›‰·˜ Û ÎψÙÛ‹Ì·Ù·;
- £· ÂÓÂÚÁÔðÔÈÂ›Ù·È ð¿ÓÙÔÙÂ Ë ÏÂÈÙÔ˘ÚÁ›· Ù˘ ·‰Ú¿ÓÂÈ·˜ ÙÔ˘ ÊÚ¤ÓÔ˘ ·Ï˘Û›‰·˜ fiÙ·Ó Ï·Ìß¿ÓÂÈ ¯ÒÚ· ¤Ó· ÎÏÒÙÛËÌ·;
- £· Ì ðÚÔÛٷهÂÈ ð¿ÓÙÔÙ ÙÔ ÊÚ¤ÓÔ ·Ï˘Û›‰·˜ ·ðfi ÙÚ·˘Ì·ÙÈÛÌfi Û ðÂÚ›ðÙˆÛË ðÔ˘ Û˘Ìß› ÎÏÒÙÛËÌ·;
- °ÛÊ¿ÏÂÈ· Áη˙ÈÔ‡
- °ÛÊ¿ÏÂÈ· Û˘ÁÎÚ¿ÙËÛ˘ ·Ï˘Û›‰·˜
- ¶ÚÔÊ˘Ï·ÎÙ‹Ú·˜ ‰ÂÍÈÔ‡ ¯ÂÚÈÔ‡
- ™‡ÛÙËÌ· ·ðfiÛßÂÛ˘ ÎÚ·‰·ÛÌÒÓ
- ¢È·ÎfiðÙ˘ ™ÙÔð
- ™ÈÁ·ÛÙ‹Ú·˜
- ºÔðÙÈÎfi˜ ÂÍÔðÏÈÛÌfi˜
- MÔÓÙ¿ÚÈÛÌ· Ô‰ËÁÔ‡ Î·È ·Ï˘Û›‰·˜
- M›ÁÌ· η˘Û›ÌÔ˘
- °¤ÌÈÛÌ· ÚÂ˙ÂÚßÔ˘¿Ú
- °ÛÊ¿ÏÂÈ· η˘Û›ÌˆÓ
- .ÂΛÓËÌ· Î·È ÛÙ·Ì¿ÙËÌ·
- ¶ÚÈÓ ·ðfi ÔðÔÈ·‰‹ðÔÙ ¯Ú‹ÛË: (33)
- °ÂÓÈΤ˜ Ô‰ËÁ›Â˜ ÂÚÁ·Û›·˜
- ¶Ó¤ÚÁÂȘ ðÚfiÏ˄˘ ÙÈÓ¿ÁÌ·ÙÔ˜
- °ÂÓÈο
- ƒ‡ıÌÈÛË Î·ÚÌðÈÚ·Ù¤Ú
- ¶ÏÂÁ¯Ô˜, Û˘ÓÙ‹ÚËÛË Î·È Û¤ÚßȘ ÙÔ˘ ðÚÔÛٷ٢ÙÈÎÔ‡ ÂÍÔðÏÈÛÌÔ‡ ÙÔ˘ ·Ï˘ÛÔðÚ›ÔÓÔ˘
- ™ÈÁ·ÛÙ‹Ú·˜
- º›ÏÙÚÔ ·¤Ú·
- MðÔ˘˙›
- ¶ÚfiÁÚ·ÌÌ· Û˘ÓÙ‹ÚËÛ˘
- ƯÓÈο ÛÙÔȯ›· (P02138HV)
- ™˘Ó‰˘·ÛÌÔ› Ô‰ËÁÔ‡ Î·È ·Ï˘Û›‰·˜
- ¶K-µÂß·›ˆÛË Û˘Ìʈӛ·˜
- VáÏen˘ zákazníku,
- Symboly vyobrazené na tûlese stroje:
- Co je co na motorové pile? (1)
- Obsah
- Pfied zahájením práce s novou motorovou pilou
- Upozornûní
- VÏdy pouÏívejte zdrav˘ rozum (2)
- Osobní ochranné pomÛcky
- Bezpeãnostní vybavení stroje
- Brzda fietûzu a chrániã levé ruky
- Bude moje ruka aktivovat brzdu fietûzu vÏdy v pfiípadû zpûtného odrazu?
- Spustí se aktivace brzdy fietûzu setrvaãností vÏdy, kdyÏ dojde ke zpûtnému odrazu?
- Ochrání mû brzda fietûzu v pfiípadû zpûtného odrazu vÏdy pfied zranûním?
- Pojistka páãky plynu
- Zachycovaã fietûzu
- Chrániã pravé ruky
- Antivibraãní systém
- Stop spínaã (vypínaã zapalování)
- Tlumiã v˘fuku
- ¤ezn˘ mechanismus
- MontáÏ fiezné li‰ty a fietûzu
- Palivo
- Plnûní paliva
- Bezpeãnost pfii manipulaci s palivem
- Startování a vypínání
- Pfied kaÏd˘m pouÏitím: (33)
- Obecné pracovní pokyny
- Jak zabránit zpûtnému rázu
- V‰eobecnû
- Nastavení karburátoru
- Kontrola a údrÏba bezpeãnostního vybavení motorové pily
- Tlumiã v˘fuku
- Vzduchov˘ filtr
- Zapalovací svíãka
- Schema technické údrÏby
- Technické údaje (P02138HV)
- Kombinace li‰ty a fietûzu
- ES Prohlá‰ení o shodû
- VáÏen˘ zákazník,
- Symboly na stroji:
- âo je ão na reÈazovej píle? (1)
- Obsah
- Pred pouÏitím novej reÈazovej píly
- DôleÏité
- VÏdy sa riaìte zdrav˘m rozumom (2)
- Osobné ochranné prostriedky
- Bezpeãnostné vybavenie stroja
- Brzda reÈaze a predn˘ chrániã ruky
- Spustím brzdu reÈaze rukou vÏdy v prípade spätného nárazu?
- Spustí zotrvaãnosÈ brzdu reÈaze vÏdy v prípade spätného nárazu?
- Zabráni brzda poraneniu vÏdy v prípade spätného nárazu?
- Poistná páãka plynu
- Zachytávaã reÈaze
- Ochrann˘ kryt pravej ruky
- Systém na tlmenie vibrácií
- Vypínaã
- Tlmiã v˘fuku
- Rezacia ãasÈ
- Namontovanie vodiacej li‰ty a reÈaze
- Palivo
- DopæÀanie paliva
- BezpeãnosÈ práce s palivom
- ·tart a stop
- Pred pouÏitím: (33)
- V‰eobecné pracovné pokyny
- Ako sa vyhnúÈ spätnému nárazu
- V‰eobecné
- Nastavenie karburátora
- Kontrola, údrÏba a servis bezpeãnostného vybavenia reÈazovej píly
- Tlmiã v˘fuku
- Vzduchov˘ filter
- Zapaºovacia svieãka
- Plán údrÏby
- Technické údaje (P02138HV)
- Kombinovanie vodiacej li‰ty a reÈaze
- EÚ vyhlásenie o zhode
- Spo‰tovani kupec!
- Simboli na stroju:
- Kaj je kaj na motorni Ïagi? (1)
- Vsebina
- Postopek pred prvo uporabo nove motorne Ïage
- Pomembno
- Zmeraj uporabljajte zdrav razum (2)
- Osebna za‰ãitna oprema
- Varnostna oprema stroja
- Zavora verige s ‰ãitnikom
- Ali bo moja roka v primeru odsunka zmeraj aktivirala zavoro za Ïago?
- Ali se bo zavora zmeraj vztrajnostno aktivirala, ko pride do odsunka?
- Ali bo me zavora za Ïago v primeru odsunka zmeraj varovala pred po‰kodbami?
- Zapora plina
- Lovilec verige
- ·ãitnik desne roke
- Sistem du‰enja tresljajev
- Izklopno stikalo
- Du‰ilec
- Rezila
- MontaÏa meãa in verige
- Pogonsko gorivo
- Toãenje goriva
- Varna uporaba goriva
- VÏig in izklop
- Pred vsako uporabo: (33)
- Splo‰na navodila za delo
- Prepreãevanje odsunka
- Splo‰no
- Nastavitev uplinjaãa
- Kontrola, vzdrÏevanje in servis varnostne opreme motorne Ïage
- Du‰ilec
- Zraãni filter
- Sveãka
- Urnik vzdrÏevanja
- Tehniãni podatki (P02138HV)
- Kombinacije meãa in verige
- ES-Izjava o skladnosti
WORKING TECHNIQUES
18 – English
1156558-26 Rev.1 2014-01-13
• Wind direction
• Arrangement of branches
• Weight of snow
• Obstacles within the reach of the tree: for example,
other trees, power lines, roads and buildings.
• Look for signs of damage and rot in the stem, this makes
it more probably that the tree will break and start to fall
before you expect it to.
You may find you are forced to let the tree fall in its natural
direction because it is impossible or dangerous to try to
make it fall in the direction you first intended.
Another very important factor, which does not affect the
felling direction but does affect your safety, is to make sure
the tree has no damaged or dead branches that might
break off and hit you during felling.
The main point to avoid is letting the tree fall onto another
tree. It is very dangerous to remove a trapped tree and
there is high accident risk. See instructions under the
heading Freeing a tree that has fallen badly.
Clearing the trunk and preparing your retreat
Delimb the stem up to shoulder height. It is safer to work
from the top down and to have the tree between you and
the saw.
Remove any undergrowth from the base of the tree and
check the area for obstacles (stones, branches, holes, etc.)
so that you have a clear path of retreat when the tree starts
to fall. Your path of retreat should be roughly 135 degrees
away from the intended felling direction.
(39)
1 Danger zone
2 Retreat path
3 Felling direction
Felling
Felling is done using three cuts. First you make the
directional cuts, which consist of the top cut and the bottom
cut, then you finish with the felling cut. By placing these
cuts correctly you can control the felling direction very
accurately.
Directional cuts
To make the directional cuts you begin with the top cut.
Stand to the right of the tree and cut on the pull stroke.
Next make the bottom cut so that it finishes exactly at the
end of the top cut.
(40)
The directional cuts should run 1/4 of the diameter through
the trunk and the angle between the top cut and bottom cut
should be 45
°.
The line where the two cuts meet is called the directional
cut line. This line should be perfectly horizontal and at right
angles (90
°) to the chosen felling direction. (41)
Felling cut
The felling cut is made from the opposite side of the tree
and it must be perfectly horizontal. Stand on the left side of
the tree and cut on the pull stroke.
Make the felling cut about 3-5 cm (1.5-2 inches) above the
bottom directional cut.
Set the spike bumper (if one is fitted) just behind the felling
hinge. Use full throttle and advance the chain/bar slowly
into the tree. Make sure the tree does not start to move in
the opposite direction to your intended felling direction.
Drive a wedge or breaking bar into the cut as soon as it is
deep enough.
(42)
Finish the felling cut parallel with the directional cut line so
that the distance between them is at least 1/10 of the trunk
diameter. The uncut section of the trunk is called the felling
hinge.
The felling hinge controls the direction that the tree falls in.
(43)
All control over the felling direction is lost if the felling hinge
is too narrow or non-existent, or if the directional cuts and
felling cut are badly placed.
When the felling cut and directional cut are complete the
tree should start to fall by itself or with the aid of a felling
wedge or breaking bar.
We recommend that you use a bar that is longer than the
diameter of the tree, so that you can make the felling cut
and directional cuts with single cutting strokes. See
instructions under the heading Technical data section to
find out which lengths of bar are recommended for your
saw.
There are methods for felling trees with a diameter larger
than the bar length. However these methods involve a
much greater risk that the kickback zone of the bar will
come into contact with the tree.
Freeing a tree that has fallen badly
Freeing a ”trapped tree”
It is very dangerous to remove a trapped tree and there is
high accident risk.
Never try to fell the tree that is trapped.
Never work in the risk zone of the hanging trapped tree.
The safest method is to use a winch.
• Tractor-mounted
• Portable
Cutting trees and branches that are in tension
Preparations: Work out which side is in tension and where
the point of maximum tension is (i.e. where it would break
if it was bent even more).
Decide which is the safest way to release the tension and
whether you are able to do it safely. In complicated
situations the only safe method is to put aside your chain
saw and use a winch.
General advice:
Position yourself so that you will be clear of the tree or
branch when the tension is released.
Make one or more cuts at or near the point of maximum
tension. Make as many cuts of sufficient depth as
necessary to reduce the tension and make the tree or
branch break at the point of maximum tension.
Never cut straight through a tree or branch that is in
tension!
IMPORTANT! During critical felling operations, hearing
protectors should be lifted immediately when sawing is
completed so that sounds and warning signals can be
heard.
!
WARNING! Unless you have special
training we advise you not to fell trees
with a diameter larger than the bar
length of your saw!