03002 LGT2554 Owner's Manual
SAFETY RULES Safe Operation Practices for Ride-On Mowers DANGER: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. • WARNING: In order to prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug.
SAFETY RULES Safe Operation Practices for Ride-On Mowers III. CHILDREN GENERAL SERVICE • Never operate machine in a closed area. • Keep all nuts and bolts tight to be sure the equipment is in safe working condition. • Never tamper with safety devices. Check their proper operation regularly. • Keep machine free of grass, leaves, or other debris build-up. Clean oil or fuel spillage and remove any fuelsoaked debris. Allow machine to cool before storing.
PRODUCT SPECIFICATIONS CUSTOMER RESPONSIBILITIES Gasoline Capacity and type: 4 Gallons Unleaded Regular • • Oil Type (API-SG-SL): SAE 30 (above 32°F) SAE 5W-30 (below 32°F) • Oil Capacity: W/ Filter: Spark Plug: Champion RC12YC (Gap: .030") Ground Speed (MPH): Forward: Reverse: Charging System: 15 AMPS @ 3600 RPM Battery: AMP/HR: MIN. CCA: Case Size: Blade Bolt Torque: 45-55 FT. LBS. 64 oz Read and observe the safety rules.
UNASSEMBLED PARTS Mower (5) Large Retainer Springs - 7/16 Mower Front Wheel (1) 3/4 O.D. Washers (1) Wheel (1) 1-1/4 O.D. Washer (2) Smaller Retainer Springs - 5/16 (1) Locknut 3/8-16 (1) Shoulder Bolt (3) 1-3/16 O.D. Washers (1) Anti-Sway Bar (1) Oil Drain Tube For Future Use Slope Sheet Keys (2) Rear Lift Link Assemblies (2) Keys ASSEMBLY BEFORE REMOVING TRACTOR FROM SKID Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes.
ASSEMBLY TO ADJUST SEAT (See Fig. 2): • TO INSTALL MOWER (See Figs. 4-12) Grasp adjustment handle(A) and pull up, slide seat to desired position and release adjustment handle. Be sure tractor is on level surface and engage parking brake. • Lower attachment lift lever to it's lowest position. CAUTION: Lift lever is spring loaded. Have a tight grip on lift lever, lower it slowly and engage in lowest position.
ASSEMBLY • • Pivot bar towards you and insert other end of bar into hole in rear mower bracket (D). Move mower as needed to insert bar. Secure with washer and retainer spring as shown A D B Fig. 8 • ATTACH REAR LIFT LINKS (C) - Lift rear corner of mower and position slot in link assembly over pin on rear mower bracket (D) and secure with washer and retainer spring. Repeat on opposite side of tractor. • Fig.
ASSEMBLY • • • • CHECK FOR PROPER POSITION OF ALL BELTS Turn steering wheel to position wheels straight forward. ATTACH FRONT LINK (E) - Work from left side of tractor. Insert rod end of link assembly through front hole in tractor front suspension bracket (F) and secure with retainer spring (G) through hole in link located behind the bracket. Insert other end of link (E) into hole in front mower bracket (H) and secure with washer and retainer spring (J).
OPERATION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning.
OPERATION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference. D P H G E N B A F Q J C M Fig. 13 Our tractors conform to the applicable safety standards of the American National Standards Institute.
OPERATION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend standard safety glasses or a wide vision safety mask worn over spectacles. HOW TO USE YOUR TRACTOR NOTE: Failure to move throttle control between half and full speed (fast) position, before stopping, may cause engine to “backfire”.
OPERATION TO MOVE FORWARD AND BACKWARD (See Fig. 17) TO ADJUST GAUGE WHEELS (See Fig. 19) Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions. NOTE: Adjust gauge wheels with tractor on a flat level surface. • Adjust mower to desired cutting height (See “TO ADJUST MOWER CUTTING HEIGHT” in this section of manual).
OPERATION TO TRANSPORT (See Fig. 13 and 21) REVERSE OPERATION SYSTEM (ROS) (See Fig. 22) When pushing or towing your tractor, be sure to disengage transmission by placing freewheel control in freewheeling position. Free wheel control is located at the rear drawbar of tractor. • Raise attachment lift to highest position with attachment lift control. • Pull freewheel control out and down into the slot and release so it is held in the disengaged position.
OPERATION BEFORE STARTING THE ENGINE TO START ENGINE (See Fig. 13) When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine. • Be sure freewheel control is in the transmission engaged position. • Sit on seat in operating position, depress brake pedal and set parking brake. • Move attachment clutch to “DISENGAGED” position.
OPERATION MOWING TIPS PURGE TRANSMISSION • CAUTION: Never engage or disengage freewheel lever while the engine is running. • To ensure proper operation and performance, it is recommended that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have developed during shipping of your tractor.
MAINTENANCE MAINTENANCE SCHEDULE BEFORE EACH USE EVERY 8 HOURS EVERY 25 HOURS EVERY 50 HOURS EVERY 100 HOURS EVERY SEASON BEFORE STORAGE Check Brake Operation Check Tire Pressure T Check Operator Presence & ROS Systems R A Check for Loose Fasteners C Check/Replace Mower Blades T Lubrication Chart 0 Check Battery Level R Clean Battery and Terminals 3 4 Check Transaxle Cooling Check Mower Levelness Check V-Belts Check Engine Oil Level Change Engine Oil (with oil filter) 1,2 Change Engine Oil (wi
MAINTENANCE TRACTOR BLADE CARE For best results mower blades must be kept sharp. Replace bent or damaged blades. Always observe safety rules when per form ing any maintenance. CAUTION: Use only a replacement blade approved by the manufacturer of your tractor. Using a blade not approved by the manufacturer of your tractor is hazardous, could damage your tractor and void your warranty.
MAINTENANCE DECK WASHOUT PORT (See Fig. 26) TRANSAXLE MAINTENANCE Your tractor’s deck is equipped with a washout port on its surface as part of its deck wash system. It should be utilized after each use. 1. Drive the tractor to a level, clear spot on your lawn, near enough to a water spigot for your garden hose to reach. IMPORTANT: Make certain the tractor’s discharge chute is directed AWAY from your house, garage, parked cars, etc. Remove bagger chute or mulch cover if attached. 2.
MAINTENANCE TO CHANGE ENGINE OIL (See Fig. 27) AIR FILTER Determine temperature range expected before oil change. All oil must meet API service classification SG-SL. • Be sure tractor is on level surface. • Oil will drain more freely when warm. • Catch oil in a suitable container. • Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine when changing oil. • Remove yellow cap from end of drain valve and install the drain tube onto the fitting.
SERVICE AND ADJUSTMENTS WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: • Depress brake pedal fully and set parking brake. • Place attachment clutch in “DISENGAGED” position. • Turn ignition key to “STOP” and remove key. • Make sure the blades and all moving parts have completely stopped. • Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. TO REMOVE MOWER (See Fig.
SERVICE AND ADJUSTMENTS NOTE: Each full turn of adjustment nut will change mower height about 3/16". • Test your adjustment by mowing some uncut grass and visually checking the appearance. Readjust, if necessary, until you are satisfied with the results. PRECISION SIDE-TO-SIDE ADJUSTMENT (See Fig. 31) • With all tires properly inflated, park tractor on level ground or driveway. B A CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap blade with heavy cloth.
SERVICE AND ADJUSTMENTS TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 34) BELT REMOVAL 1. Remove mower (See “TO REMOVE MOWER” section in this manual). NOTE: Observe entire motion drive belt and position of all belt guides and keepers. MOWER DRIVE BELT REMOVAL • Park tractor on a level surface. Engage parking brake. • Lower attachment lift lever to its lowest position. • Disengage belt tension rod (K) from lock bracket (L). 2. Disconnect clutch wire harness (A). 3.
SERVICE AND ADJUSTMENTS TO REMOVE WHEEL (See Fig. 36) MOTION CONTROL LEVER • • Block up axle securely. Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose). • Repair tire and reassemble. • On rear wheels only: align grooves in rear wheel hub and axle. Insert square key. • Replace washers and snap retaining ring securely in axle groove. • Replace axle cover.
SERVICE AND ADJUSTMENTS REPLACING BATTERY (See Fig. 39) TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 40) WARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from accidental grounding. • • • • • • • • • • • • Raise hood. Unsnap headlight wire connector. Stand in front of tractor.
STORAGE ENGINE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. FUEL SYSTEM IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS DURING STORAGE.
TROUBLESHOOTING POINTS PROBLEM Will not start CAUSE 1. 2. 3. 4. 5. 6. 7. CORRECTION Out of fuel. Engine not “CHOKED” properly. Engine flooded. Bad spark plug. Dirty air filter. Dirty fuel filter. Water in fuel. 1. 2. 3. 4. 5. 6. 7. Fill fuel tank. See “TO START ENGINE” in Operation section. Wait several minutes before attempting to start. Replace spark plug. Clean/replace air filter. Replace fuel filter. Empty fuel tank and carburetor, refill tank with fresh gasoline and replace fuel filter. 8.
TROUBLESHOOTING POINTS PROBLEM CAUSE CORRECTION Engine continues to run when operator leaves seat with attachment clutch engaged 1. Faulty operator-safety presence control system. 1. Check wiring, switches and connections. If not corrected, contact an authorized service center/ department. Poor cut - uneven 1. 2. 3. 4. 5. Worn, bent or loose blade. Mower deck not level. Buildup of grass, leaves, trash under mower. Bent blade mandrel.
TRACTOR - MODEL NO. LGT2554 (96045001700), PRODUCT NO. 960 45 00-17 DECALS 15 16 17 16 3 4 9 1 14 14 8 5 2 KEY NO. 1 2 3 4 5 8 9 PART NO. 532 41 91-38 532 42 38-30 532 42 41-02 532 19 15-54 532 17 84-55 532 19 87-85 532 14 50-05 DESCRIPTION Decal, Warning Decal, Ethanol E85 Decal, Warning Spark Arrestor Decal, Hood Cust Resp Decal, Caution Decal, Mower Sch. Decal, Battery Dnge/Poi WHEELS AND TIRES 1 2 11 3 4 7 10 5 6 9 8 KEY NO. 14 15 16 17 ------ PART NO.
TRACTOR - MODEL NO. LGT2554 (96045001700), PRODUCT NO.
TRACTOR - MODEL NO. LGT2554 (96045001700), PRODUCT NO.
TRACTOR - MODEL NO. LGT2554 (96045001700), PRODUCT NO. 960 45 00-17 ELECTRICAL KEY NO. PART NO.
TRACTOR - MODEL NO. LGT2554 (96045001700), PRODUCT NO.
TRACTOR - MODEL NO. LGT2554 (96045001700), PRODUCT NO. 960 45 00-17 CHASSIS KEY NO. PART NO.
TRACTOR - MODEL NO. LGT2554 (96045001700), PRODUCT NO.
TRACTOR - MODEL NO. LGT2554 (96045001700), PRODUCT NO. 960 45 00-17 DRIVE KEY NO. PART NO.
TRACTOR - MODEL NO. LGT2554 (96045001700), PRODUCT NO. 960 45 00-17 ENGINE 21 1 20 22 81 87 111 18 82 84 45 62 28 15 113 109 37 69 12 28 69 37 11 70 71 91 79 41 29 2 42 85 9 90 SPARK ARRESTER KIT Engine-tex_Kohl-2cyl_1_r2 KEY NO. 1 2 9 11 12 15 18 20 21 22 28 29 37 41 42 45 62 PART NO.
TRACTOR - MODEL NO. LGT2554 (96045001700), PRODUCT NO. 960 45 00-17 SEAT ASSEMBLY 1 8 8 8 7 7 8 41 40 10 21 6 37 6 37 2 44 43 21 3 seat-tex_6.5SL_3 KEY NO. PART NO. DESCRIPTION 1 2 3 6 7 8 10 21 532 40 66-21 532 18 01-66 532 14 06-75 873 80 06-00 532 12 41-81 532 17 18-77 532 19 69-77 532 17 18-52 Seat Bracket Pivot Fender Strap, Asm Fender Nut, Lock w/Ins. 3/8-16 unc Spring, Seat Cprsn Bolt 5/16-18 unc x 3/4 w/Sems Pan, Seat Bolt, Shoulder 5/16-18 KEY NO. PART NO.
TRACTOR - MODEL NO. LGT2554 (96045001700), PRODUCT NO.
TRACTOR - MODEL NO. LGT2554 (96045001700), PRODUCT NO. 960 45 00-17 STEERING ASSEMBLY KEY NO. PART NO.
TRACTOR - MODEL NO. LGT2554 (96045001700), PRODUCT NO.
TRACTOR - MODEL NO. LGT2554 (96045001700), PRODUCT NO. 960 45 00-17 MOWER DECK KEY NO. PART NO.
TRACTOR - MODEL NO. LGT2554 (96045001700), PRODUCT NO. 960 45 00-17 MOWER LIFT 87 87 7 90 98 89 3 10 88 97 2 91 97 91 87 89 lift-tex_3 89 87 KEY NO. PART NO. DESCRIPTION 2 3 7 10 87 88 89 532 19 52-23 532 19 52-30 532 41 15-55 532 19 63-14 532 19 42-09 532 19 53-04 819 19 19-12 Shaft Asm., Lift Lever Asm., Lift RH Grip, Lever Spring Torsion Pin Cotter 7/16 Bow Tie Lock Spring Lift Assist Washer Clear Zinc KEY NO. PART NO.
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION FOL DA L O NG D THIS O I T S T A E D LIN 1 5 DEG E RE E S LOP E ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL 15 DEGREES MAX. WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than 15 degrees. Make turns gradually to prevent tipping or loss of control. Exercise extreme caution when changing direction on slopes. 1. Fold this page along dotted line indicated above. 2.
532 42 57-55 Rev.1 04.20.09 SR Printed in the U.S.A.
