Operator’s manual (EPA) 333RJ 335RJX-series Please read the operator’s manual carefully and make sure you understand the instructions before using the machine.
KEY TO SYMBOLS Symbols Only use non-metallic, flexible cutting attachments, i.e. trimmer heads with trimmer cord. WARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others. 1. Please read the operator’s manual carefully and make sure you understand the instructions before using the machine.
CONTENTS Contents KEY TO SYMBOLS Symbols .................................................................... CONTENTS Contents .................................................................... Note the following before starting: ............................. INTRODUCTION Dear customer! .......................................................... WHAT IS WHAT? What is what on the clearing saw? ............................ GENERAL SAFETY PRECAUTIONS Impor tant ...............................................
CONTENTS Note the following before starting: Please read the operator’s manual carefully. Maintenance, replacement, or repair of the emission control devices and system may be performed by any nonroad engine repair establishment or individual. ! ! WARNING! Long-term exposure to noise can result in permanent hearing impairment. So always use approved hearing protection. WARNING! Under no circumstances may the design of the machine be modified without the permission of the manufacturer.
INTRODUCTION Dear customer! Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Huskvarna River, for production of muskets. The location was logical, since water power was harnessed from the Huskvarna River to create the water-powered plant.
WHAT IS WHAT? 32 29 23 23 30 24 25 26 31 28 27 What is what on the clearing saw? 1 Trimmer head 17 Choke control 2 Grease filler cap, bevel gear 18 Air purge 3 Bevel gear 19 Locking nut 4 Cutting attachment guard 20 Support flange 5 Shaft 21 Support cup 6 Handle adjustment 22 Blade 7 Loop handle 23 Drive disc 8 Suspension ring 24 Transport guard 9 Stop switch 25 Spark plug spanner 10 Throttle lockout 26 Locking pin 11 Throttle control 27 Socket spanner 12 Spark plug
GENERAL SAFETY PRECAUTIONS Important Personal protective equipment IMPORTANT! IMPORTANT! The machine is only designed for trimming grass. A clearing saw, brushcutter or trimmer can be dangerous if used incorrectly or carelessly, and can cause serious or fatal injury to the operator or others. It is extremely important that you read and understand the contents of this operator’s manual.
GENERAL SAFETY PRECAUTIONS BOOTS Wear boots with steel toe-caps and non-slip sole. return springs. This arrangement means that the throttle control is automatically locked at the idle setting. A B CLOTHING Wear clothes made of a strong fabric and avoid loose clothing that can catch on twigs and branches. Always wear heavy, long pants. Do not wear jewellery, shorts sandals or go barefoot. Secure hair so it is above shoulder level.
GENERAL SAFETY PRECAUTIONS Stop switch Vibration damping system Use the stop switch to switch off the engine. Your machine is equipped with a vibration damping system that is designed to reduce vibration and make operation easier. Start the engine and make sure the engine stops when you move the stop switch to the stop setting. Cutting attachment guard This guard is intended to prevent loose objects from being thrown towards the operator.
GENERAL SAFETY PRECAUTIONS Muffler Regularly check that the muffler is securely attached to the machine. The muffler is designed to keep noise levels to a minimum and to direct exhaust fumes away from the user. A muffler fitted with a catalytic converter is also designed to reduce harmful exhaust gases. If the muffler on your machine is fitted with a spark arrestor screen this must be cleaned regularly. A blocked screen will cause the engine to overheat and may lead to serious damage.
GENERAL SAFETY PRECAUTIONS Locking nut Cutting equipment This section describes how to choose and maintain your cutting equipment in order to: A locking nut is used to secure some types of cutting attachment. • Reduce the risk of blade thrust. • Obtain maximum cutting performance. • Extend the life of cutting equipment. IMPORTANT! Only use cutting attachments with the guards we recommend! See the chapter on Technical data.
GENERAL SAFETY PRECAUTIONS General rules Trimmer head IMPORTANT! Always ensure the trimmer cord is wound tightly and evenly around the drum, otherwise the machine will generate harmful vibration. Only use cutting attachments with the guards we recommend! See the chapter on Technical data. • Only use the recommended trimmer heads and trimmer cords. These have been tested by the manufacturer to suit a particular engine size. This is especially important when a fully automatic trimmer head is used.
ASSEMBLY Fitting the J-handle • Clip the loop handle onto the shaft. Note that the loop handle must be fitted between the arrows on the shaft. • Slide the spacer into the slot in the loop handle. • Fit the nut, knob and screw. Do not overtighten. • Attach the J-handle to the loop handle using the three screws, as shown.
ASSEMBLY Fitting a blade guard, grass blade and grass cutter Fitting other guards and cutting attachments • G F E Hang the trimmer guard/combination guard (A) on the two hooks on the plate holder (M). Bend the guard around the shaft and tighten it with the bolt (L) on the opposite side of the shaft. Use the locking pin (C). Place the locking pin in the groove on the screw head and tighten. See diagram.
FUEL HANDLING Fuel safety Gasoline Never start the machine: 1 If you have spilled fuel on it. Wipe off the spillage and allow remaining fuel to evaporate. 2 If you have spilled fuel on yourself or your clothes, change your clothes. Wash any part of your body that has come in contact with fuel. Use soap and water. 3 If the machine is leaking fuel. Check regularly for leaks from the fuel cap and fuel lines.
FUEL HANDLING Fueling Mixing • Always mix the gasoline and oil in a clean container intended for fuel. • Always start by filling half the amount of the gasoline to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of gasoline. • Mix (shake) the fuel mixture thoroughly before filling the machine’s fuel tank. ! WARNING! Taking the following precautions, will lessen the risk of fire: Do not smoke or place hot objects near fuel.
STARTING AND STOPPING Check before starting • trimmer guard if they have been exposed to impact or are cracked. Check the blade to ensure that no cracks have formed at the bottom of the teeth or by the centre hole. The most common reason why cracks are formed is that sharp corners have been formed at the bottom of the teeth while sharpening or that the blade has been used with dull teeth. Discard a blade if cracks are found. • Never use the machine without a guard nor with a defective guard.
STARTING AND STOPPING Primer bulb: Press the air purge repeatedly until fuel begins to fill the bulb. The bulb need not be completely filled. Stopping Stop the engine by switching off the ignition. ! WARNING! When the engine is started with the choke in either the choke or start throttle positions the cutting attachment will start to rotate immediately. Hold the body of the machine on the ground using your left hand (CAUTION! Not with your foot!).
WORKING TECHNIQUES General working instructions 6 Always hold the machine with both hands. Hold the machine on the right side of your body. 7 Keep the cutting attachment below waist level. 8 Switch off the engine before moving to another area. Fit the transport guard before carrying or transporting the equipment any distance. 9 Never put the machine down with the engine running unless you have it in clear sight.
WORKING TECHNIQUES Basic working techniques • Always slow the engine to idle speed after each working operation. Long periods at full throttle without any load on the engine can lead to serious engine damage. Let the support cup rest lightly against the ground. It is used to protect the blade from hitting the ground. • Reduce the risk of material wrapping around the blade by following these instructions: 1Always work at full throttle.
WORKING TECHNIQUES Cutting • The trimmer is ideal for cutting grass that is difficult to reach using a normal lawn mower. Keep the cord parallel to the ground when cutting. Avoid pressing the trimmer head against the ground as this can ruin the lawn and damage the tool. • Do not allow the trimmer head to constantly come into contact with the ground during normal cutting. Constant contact of this type can cause damage and wear to the trimmer head.
MAINTENANCE Carburetor finely adjusted. Fine adjustment should be carried out by a skilled technician. Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. After the engine has used 8-10 tanks of fuel the engine will be run-in.
MAINTENANCE Fine adjustment of the idle speed T Adjust the idle speed using the idle adjustment screw T, if it is necessary to readjust. First turn the idle adjustment screw T clockwise until the cutting attachment starts to rotate. Then turn the screw anticlockwise until the cutting attachment stops. The idle speed is correctly adjusted when the engine will run smoothly in every position. The idle speed should also be well below the speed at which the cutting attachment starts to rotate. to run unevenly.
MAINTENANCE frequently blocked, this can be a sign that the performance of the catalytic converter is impaired. Contact your dealer to inspect the muffler. A blocked screen will cause the machine to overheat and result in damage to the cylinder and piston. CAUTION! Never use a machine with a defective muffler. ! WARNING! Mufflers fitted with catalytic converters get very hot during use and remain so for some time after stopping. This also applies at idle speed. Contact can result in burns to the skin.
MAINTENANCE Oiling the air filter Always use special filter oil. Filter oil contains a solvent to make it spread evenly through the filter. You should therefore avoid skin contact. Put the filter in a plastic bag and pour the filter oil over it. Knead the plastic bag to distribute the oil. Squeeze the excess oil out of the filter inside the plastic bag and pour off the excess before fitting the filter to the machine. Never use common engine oil.
MAINTENANCE Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. The user must only carry out the maintenance and service work described in this manual. More extensive work must be carried out by an authorised service workshop. Maintenance Daily maintenance Clean the outside of the machine. X Make sure the throttle trigger lock and the throttle function correctly from a safety point of view.
TECHNICAL DATA Technical data Technical data 333RJ 335RJx Engine Cylinder displacement, cu.in/cm3 2,11/34,6 2,11/34,6 Cylinder bore, inch/mm 1,50/38,0 1,50/38,0 Stroke, inch/mm 1,20/30,5 1,20/30,5 Idle speed, rpm 2900 2900 Recommended max. fast idle speed, rpm 11500 11500 Speed of output shaft, rpm 8220 8220 Max. engine output, acc.
FEDERAL AND CALIFORNIA EMISSIONS CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The EPA (U.S. Environmental Protection Agency), CARB (California Air Resources Board), Environment Canada and Husqvarna Forest & Garden are pleased to explain the emissions control system’s warranty on your 2007 and later small off-road engine. In U.S.
FEDERAL AND CALIFORNIA EMISSIONS CONTROL WARRANTY STATEMENT EMISSION WARRANTY PARTS LIST 1 Carburetor and internal parts 2 Intake pipe, airfilter holder and carburetor bolts. 3 Airfilter and fuelfilter covered up to maintenance schedule. 4 Spark Plug, covered up to maintenance schedule 5 Ignition Module 6 Muffler with catalytic converter 7 Fuel tank WHAT IS NOT COVERED All failures caused by abuse, neglect or improper maintenance are not covered.
S35 2 3 2,4-2,7 mm .095-.
S35 3 2 2,4-2,7 mm .095-.
T35, T35x 2 3 2,4-2,7 mm .095-.
T45, T45x 2 3 2,7-3,3 mm .106-.
1150887-95 ´®z+Rxo¶5A¨ ´®z+Rxo¶5A¨ 2008-03-05