Operators Manual
Table Of Contents
- Contents
- Introduction
- Safety
- Assembly
- Operation
- Maintenance
- Introduction
- Maintenance schedule
- Maintenance and checks of the safety devices on the product
- To do a check of the brake band
- To do a check of the front hand guard and the chain brake activation
- To do a check of the chain brake
- To do a check of the throttle trigger and throttle trigger lockout
- To do a check of the chain catcher
- To do a check of the right hand guard
- To do a check of the vibration damping system
- To do a check of the start/stop switch
- To do a check of the muffler
- Carburetor with adjustment limitations
- Carburetor without adjustment limitations
- To examine if the carburetor is correctly adjusted
- To replace a broken or worn starter rope
- To tighten the recoil spring
- To assemble the starter housing on the product
- To clean the air filter
- To do a check of the spark plug
- To calculate the felling direction
- To sharpen the saw chain
- To adjust the tension of the saw chain
- To do a check of the saw chain lubrication
- To do a check of the rim sprocket
- To lubricate the needle bearing
- To examine the cutting equipment
- To do a check of the guide bar
- To do maintenance on the fuel tank and the chain oil tank
- To adjust the chain oil flow
- Air cleaning system
- To clean the cooling system
- Troubleshooting
- Transportation and storage
- Technical data
- Accessories
- EC Declaration of Conformity
1. In conditions with snow, a winter cover is available.
Assemble the winter cover on the starter housing.
The winter cover decreases the flow of cool air and
keeps snow away from the carburetor space.
CAUTION: Remove the winter cover if the
temperature increases above 0°C/32°F. Risk
of too high engine temperature and damage
to the engine.
Heated handles (372 XPG)
The product has heated front and rear handles. The
electrical heating coils are powered by a generator.
Push the switch to engage the heat in the handles. The
heat is on when you can see the red mark on the switch.
Electrical carburetor heating (372 XPG)
Adjustment of the carburetor heating is done electrically
through a thermostat. This keeps the correct carburetor
temperature and prevents ice in the carburetor.
Maintenance
Introduction
WARNING: Read and understand the safety
chapter before you do maintenance on the
product.
Maintenance schedule
Daily maintenance Weekly maintenance Monthly maintenance
Clean the external parts of the prod-
uct and make sure that there is no oil
on the handles.
Clean the cooling system. Refer to
To clean the cooling system on page
32
.
Do a check of the brake band. Refer
to
To do a check of the brake band
on page 21
.
Do a check of the throttle trigger and
throttle trigger lockout. Refer to
To do
a check of the throttle trigger and
throttle trigger lockout on page 22
.
Do a check of the starter, starter rope
and return spring.
Do a check of the clutch centre,
clutch drum and clutch spring.
Make sure that there is no damage
on the vibration damping units.
Lubricate the needle bearing. Refer
to
To lubricate the needle bearing on
page 31
.
Clean the spark plug. Refer to
To do
a check of the spark plug on page
27
.
Clean and do a check of the chain
brake. Refer to
To do a check of the
front hand guard and the chain brake
activation on page 21To do a check
of the chain brake on page 22
.
Remove burrs from the edges of the
guide bar. Refer to
To do a check of
the guide bar on page 31
.
Clean the external parts of the carbu-
rettor.
Do a check of the chain catcher. Re-
fer to
To do a check of the chain
catcher on page 22
.
Clean or replace the spark arrestor
mesh on the muffler.
Do a check of the fuel filter and the
fuel hose. Replace if necessary.
20 593 - 001 - 20.01.2020