Operators Manual
Table Of Contents
- Contents
- Introduction
- Safety
- Installation
- Introduction - Installation
- Main components for installation
- General preparations
- Before the installation of the wires
- Installation of the product
- To put the wire into position with stakes
- To bury the boundary wire or the guide wire
- To extend the boundary wire or the guide wire
- After the installation of the product
- Automower® Connect app
- To do the product settings
- To get access to the menu
- Menu structure
- Schedule
- Weather timer
- Lawn Coverage
- Methods for the product to find the charging station
- Corridor width
- Exit angle
- Reversing distance
- Drive Past Wire function
- Settings
- ECO mode
- General
- Accessories
- Operation
- Maintenance
- Troubleshooting
- Transportation, storage and disposal
- Technical data
- Warranty
- EC Declaration of Conformity
4. Save a profile for the new charging station,
or select a profile in the list. Do steps 1–4 in
To save settings to a profile on page 33
, or
do steps 1–3 in
To use a profile on page 33
.
3.12.11 ECO mode
If
ECO mode
is activated, it switches off the
signal in the boundary loop, the guide wire and
the charging station, when the product is parked
or is charging.
Note: Use
ECO mode
to save energy and avoid
interference with other equipment, for example
hearing loops or garage doors.
Note: To start the product manually in the work
area, push the STOP button before you remove
the product from the charging station. If not, the
product can not be started in the work area.
3.12.11.1 To set the ECO mode
1. Do steps 1–3 in
To get access to the menu
on page 26
.
2. Use the arrow buttons and the OK button to
move through the menu structure
Settings >
ECO mode
.
3. Push the OK button to select the
ECO
mode
.
4. Push the BACK button.
3.12.11.2 Spiral Cutting
The product cuts the grass in a spiral pattern if
the grass is longer in an area.
Spiral cutting
can
be set in 5 levels:
• Low-
• Low
• Mid
• High
• High+
The level sets how sensitive the product is to
changes in grass height.
Note:
Spiral cutting
is only started in the Main
area mode. Cutting in the
Secondary area
mode
does not let the product to start
Spiral cutting
.
Spiral Cutting
does not start in slopes steeper
than 15%.
To set the Spiral Cutting
1. Do steps 1–3 in
To get access to the menu
on page 26
.
2. Use the arrow buttons and the OK button to
move through the menu structure
Settings >
Spiral Cutting > Use Spiral Cutting
.
3. Push the BACK button.
To set the level of Spiral Cutting
1. Do steps 1–3 in
To get access to the menu
on page 26
.
2. Use the arrow buttons and the OK button to
move through the menu structure
Settings >
Spiral Cutting > Use Spiral Cutting >
Intensity
.
3. Use the left arrow button to select the level
of the Spiral Cutting.
4. Push the BACK button.
3.12.11.3 Slope control
In order to decrease lawn wear near the
boundary wire in slopes, the product prevents to
move in the opposite direction when the product
operates in a slope.
Slope control
is enabled in
the factory settings.
To set the Slope control
1. Do steps 1–3 in
To get access to the menu
on page 26
.
2. Use the arrow buttons and the OK button to
move through the menu structure
Settings >
Slope control > Use Slope control
.
3. Push the BACK button.
3.12.12 General
In
General
you can change the general settings
of the product.
3.12.12.1 To set the time & date
1. Do steps 1–3 in
To get access to the menu
on page 26
.
2. Use the arrow buttons and the OK button to
move through the menu structure
Settings >
General > Time & Date
.
3. Use the number buttons to set the time and
then push the BACK button.
4. Use the number buttons to set the date and
then push the BACK button.
5. Use the arrow buttons to set the time format
and then push the BACK button.
34
- Installation
1201 - 003 - 25.03.2020