Operators Manual
Table Of Contents
- Contents
- Introduction
- Safety
- Installation
- Introduction - Installation
- Main components for installation
- General preparations
- Before the installation of the wires
- Installation of the product
- To put the wire into position with stakes
- To bury the boundary wire or the guide wire
- To extend the boundary wire or the guide wire
- After the installation of the product
- Automower® Connect app
- To do the product settings
- To get access to the menu
- Menu structure
- Schedule
- Weather timer
- Lawn Coverage
- Methods for the product to find the charging station
- Corridor width
- Exit angle
- Reversing distance
- Drive Past Wire function
- Settings
- ECO mode
- General
- Accessories
- Operation
- Maintenance
- Troubleshooting
- Transportation, storage and disposal
- Technical data
- Warranty
- EC Declaration of Conformity
6. Use the arrow buttons to set the date format
and then push the BACK button.
3.12.12.2 To set the language
1. Do steps 1–3 in
To get access to the menu
on page 26
.
2. Use the arrow buttons and the OK button to
move through the menu structure
Settings >
General > Language.
3. Use the arrow buttons to select language
and then push the BACK button.
3.12.12.3 To set the Country & Timezone
1. Do steps 1–3 in
To get access to the menu
on page 26
.
2. Use the arrow buttons and the OK button to
move through the menu structure
Settings >
General > Country & Timezone.
3. Use the arrow buttons to select country and
then push the BACK button.
3.12.12.4 To set the unit format
1. Do steps 1–3 in
To get access to the menu
on page 26
.
2. Use the arrow buttons and the OK button to
move through the menu structure
Settings >
General > Unit format.
3. Use the arrow buttons to select unit format
and then push the BACK button.
3.12.12.5 To reset all user settings
1. Do steps 1–3 in
To get access to the menu
on page 26
.
2. Use the arrow buttons and the OK button to
move through the menu structure
Settings >
General > Reset all user settings
.
3. Use the right arrow button to select
Proceed
with reset of all user settings?
4. Push the OK button to reset all the user
settings.
Note:
Security level, PIN code, Loop signal,
Messages, Date & Time, Language
and
Country
settings
are not reset.
3.12.12.6 The About menu
The
About
menu displays information about the
product, for example serial number and firmware
versions.
3.12.13 Accessories
Settings for accessories mounted on
the product can be made in this menu.
3.12.13.1 Information
This menu handles accessories mounted on the
product. Contact your local Husqvarna
representative for more information on available
accessories.
3.12.13.2 Automower
®
Connect app
The app gives two modes of connectivity: Long-
range cellular connectivity and Short-range
Bluetooth
®
connectivity. Automower
®
420/430X/
440/450X support only Bluetooth
®
communication. If they get Automower
®
Connect
installed as an accessory, they also support
cellular communication.
The product can connect to mobile devices that
have the Automower
®
Connect app installed.
Automower
®
Connect is a free app for your
mobile device. The Automower
®
Connect app
gives extended functions to your Husqvarna
product. You can:
• See the status of your product.
• Change settings to your product.
• Get extended product information.
• Get an alarm if the product moves out of the
work area.
• See statistics of your product.
Note:
All countries do not support Automower
®
Connect because of legal reasons and regional
specified cellular systems. The included
Automower
®
Connect lifetime service only
applies if there is a third part sub-supplier of
2G/3G/4G available in the operational area. In
some countries Bluetooth
®
is not available due to
legal reasons.
To install the Automower
®
Connect app
1. Download the Automower
®
Connect app on
your mobile device.
2. Sign up for a Husqvarna account in the
Automower
®
Connect app.
3. An e-mail is sent to the registered e-mail
address. Follow the instructions in the e-mail
1201 - 003 - 25.03.2020
Installation - 35