Operators Manual
Table Of Contents
- Contents
- Introduction
- Safety
- Installation
- Introduction - Installation
- Main components for installation
- General preparations
- Before the installation of the wires
- Installation of the product
- To put the wire into position with stakes
- To bury the boundary wire or the guide wire
- To extend the boundary wire or the guide wire
- After the installation of the product
- Automower® Connect app
- To do the product settings
- To get access to the menu
- Menu structure
- Schedule
- Weather timer
- Lawn Coverage
- Methods for the product to find the charging station
- Corridor width
- Exit angle
- Reversing distance
- Drive Past Wire function
- Settings
- ECO mode
- General
- Accessories
- Operation
- Maintenance
- Troubleshooting
- Transportation, storage and disposal
- Technical data
- Warranty
- EC Declaration of Conformity
in less than 24 hours to validate your
account.
4. Log in to your Husqvarna account in the
Automower
®
Connect app.
3.12.13.3 Automower
®
Connect@Home
Connect@Home uses a short-range Bluetooth
®
wireless technology. This means that you can
communicate between the mobile device and the
product while you are in communication range.
An icon for Bluetooth
®
communication will show
in the product display when the product is
connected with your mobile device.
Note: Connect@Home has equivalent but not as
extended functions as Automower
®
Connect, and
uses the same app.
To pair Connect@Home and the product
1. Do steps 1–3 in
To get access to the menu
on page 26
.
2. Use the arrow buttons and the OK button to
move through the menu structure
Accessories > Connect@Home > Pairing >
New pairing
.
3. Follow the instructions in the app.
Note: Automower
®
Connect is always connected
to your product as long as the mobile device
have connection with the mobile network, the
product is charged and switched on.
To remove paired accounts
1. Do steps 1–3 in
To get access to the menu
on page 26
.
2. Use the arrow buttons and the OK button to
move through the menu structure
Accessories > Connect@Home > Pairing >
Remove paired accounts
.
3. Push the OK button to select
YES/NO
to
remove all paired accounts.
3.12.13.4 Automower
®
Connect
Automower
®
Connect is included in 430X/450X
and is available as an accessory for Automower
®
420/440.
To pair Automower
®
Connect and the product
1. Do steps 1–3 in
To get access to the menu
on page 26
.
2. Use the
arrow buttons and the OK button to
move through the menu structure
Accessories > Automower
®
Connect >
Pairing > New pairing
.
3. Follow the instructions in the app.
To enable the GeoFence function
GeoFence is a GPS-based theft protection that
makes a virtual fence for the product. You will get
a message if the product is moved on the other
side of the GeoFence.
1. Put the product in the center of the work
area.
2. Do steps 1–3 in
To get access to the menu
on page 26
.
3. Use the arrow buttons and the OK button to
move through the menu structure
Accessories > Automower Connect >
GeoFence > Activate GeoFence
.
4. Push the OK button.
5. Select
Activate GeoFence
and push the OK
button.
To set a new center point for the Geofence
function
1. Put the product in the center of the work
area.
2. Do steps 1–3 in
To get access to the menu
on page 26
.
3. Use the arrow buttons and the OK button to
move through the menu structure
Accessories > Automower Connect >
GeoFence > New center point
.
4. Push the OK button.
To set the GeoFence level of sensitivity
The higher level of GeoFence sensitivity, the
easier the alarm starts.
1. Do steps 1–3 in
To get access to the menu
on page 26
.
2. Use the arrow buttons and the OK button to
move through the menu structure
Accessories > Automower Connect >
GeoFence
.
3. Use the arrow buttons to select level of
GeoFence sensitivity.
4. Push the BACK button.
To use the SMS function
The SMS function sends you an SMS when the
product is moved out of the GeoFence.
36
- Installation
1201 - 003 - 25.03.2020