Operators Manual
Table Of Contents
- Symbols on the machine:
- Symbols in the operator’s manual:
- Contents
- Dear Customer,
- Before using a new chain saw
- Important
- Always use common sense (2)
- Personal protective equipment
- Machine¢s safety equipment
- Chain brake and front hand guard
- Will my hand always activate the chain brake during a kickback?
- Will my inertia activated chain brake always activate during kickback in the event of a kickback?
- Will my chain brake always protect me from injury in the event of a kickback?
- Throttle trigger lockout
- Chain catcher
- Right hand guard
- Vibration damping system
- Stop switch
- Muffler
- Cutting equipment
- Fitting the bar and chain
- Fuel
- Fueling
- Fuel safety
- Starting and stopping
- Before use: (61)
- General working instructions
- How to avoid kickback
- General
- Carburettor adjustment
- Checking, maintaining and servicing chain saw safety equipment
- Muffler
- Starter housing
- Air filter
- Spark plug
- Needle bearing lubrication
- Cooling system
- ”Air Injection” centrifugal cleaning
- Winter use
- Maintenance schedule
- Technical data
- Recommended cutting equipment
- Filing equipment and filing angles
- EC Declaration of Conformity
- Symboles sur la machine:
- Symboles dans le manuel:
- Sommaire
- Cher client,
- Mesures à prendre avant de mettre en usage une tronçonneuse neuve
- Important!
- Utilisez toujours votre bon sens (2)
- Équipement de protection personnelle
- Équipement de sécurité de la machine
- Frein de chaîne avec arceau protecteur
- Ma main active-t-elle toujours le frein de chaîne en cas de rebond?
- L’inertie du frein de chaîne est-elle toujours activée en cas de rebond?
- Le frein de chaîne me protège-t-il toujours des blessures en cas de rebond?
- Blocage de l’accélération
- Capteur de chaîne
- Protection de la main droite
- Système anti-vibrations
- Bouton d’arrêt
- Silencieux
- Équipement de coupe
- Montage du guide-chaîne et de la chaîne
- Carburant
- Remplissage de carburant
- Sécurité carburant
- Démarrage et arrêt
- Avant chaque utilisation: (61)
- Méthodes de travail
- Mesures anti-rebond
- Généralités
- Réglage du carburateur
- Contrôle, maintenance et entretien des équipements de sécurité de la tronçonneuse
- Silencieux
- Lanceur
- Filtre à air
- Bougie
- Graissage du roulement à aiguilles
- Système de refroidissement
- Épuration centrifuge ”Air Injection”
- Utilisation hivernale
- Schéma d’entretien
- Caractéristiques techniques
- Équipement de coupe recommandé
- Équipement et angles d’affûtage
- Déclaration CE de conformité
- Símbolos en la máquina:
- Símbolos en el manual de instrucciones:
- Índice
- Apreciado cliente:
- Medidas a tomar antes de utilizar una motosierra nueva
- Importante
- Emplee siempre el sentido común (2)
- Equipo de protección personal
- Equipo de seguridad de la máquina
- Freno de cadena con protección contra reculadas
- ¿Activará siempre mi mano el freno de cadena en caso de reculada?
- ¿Se activa siempre por inercia el freno de cadena cuando se produce una reculada?
- ¿Me protegerá siempre el freno de cadena contra daños si se produce una reculada?
- Fiador del acelerador
- Captor de cadena
- Protección de la mano derecha
- Sistema amortiguador de vibraciones
- Botón de parada
- Silenciador
- Equipo de corte
- Montaje de la espada y la cadena
- Carburante
- Repostaje
- Seguridad en el uso del combustible
- Arranque y parada
- Antes de utilizar la máquina: (61)
- Instrucciones generales de trabajo
- Medidas preventivas de las reculadas
- Generalidades
- Ajuste del carburador
- Control, mantenimiento y servicio del equipo de seguridad de la motosierra
- Silenciador
- Mecanismo de arranque
- Filtro de aire
- Bujía
- Lubricación del cojinete de agujas
- Sistema refrigerante
- Depuración centrífuga ”Air Injection”
- Utilización en invierno
- Programa de mantenimiento
- Datos técnicos
- Equipo de corte recomendado
- Equipo de afilado y ángulos de afilado
- Declaración CE de conformidad
- Símbolos na máquina:
- Símbolos nas instruções para o uso:
- Índice
- Prezado cliente!
- Precauções antes de usar a nova moto-serra
- Importante
- Use sempre o seu bom senso (2)
- Equipamento de protecção pessoal
- Equipamento de segurança da máquina
- Travão de corrente com protector anti- retrocesso
- A minha mão activará sempre o travão da corrente na ocorrência de um retrocesso?
- A activação do travão da corrente por inércia funcionará sempre na ocorrência de um retrocesso?
- O travão da corrente proteger-me-á sempre de ferimentos na ocorrência de um retrocesso?
- Bloqueio do acelerador
- Retentor de corrente
- Protector da mão direita
- Sistema anti-vibração
- Contacto de paragem
- Silenciador
- Equipamento de corte
- Montagem da lâmina e corrente
- Combustível
- Abastecimento
- Segurança no manejo de combustível
- Arranque e paragem
- Sempre, antes de usar: (61)
- Instruções gerais de trabalho
- Medidas de prevenção contra retrocessos
- Noções gerais
- Afinação do carburador
- Controlo, manutenção e assistência ao equipamento de segurança da moto-serra
- Silenciador
- Dispositivo de arranque
- Filtro de ar
- Vela de ignição
- Lubrificação do rolamento de agulhas
- Sistema de arrefecimento
- Purificação centrífuga ”Air injection”
- Uso durante o inverno
- Esquema de manutenção
- Especificações técnicas
- Equipamento de corte recomendado
- Equipamento e ângulos de afiação
- Certificado CE de conformidade
GENERAL SAFETY PRECAUTIONS
English – 15
1157680-38 Rev.4 2018-10-15
Check the chain tension every time you refuel. NOTE! A
new chain has a running-in period during which you
should check the tension more frequently.
Tension the chain as tightly as possible, but not so tight
that you cannot pull it round freely by hand.
(26)
445 II, 450 II
• Loosen the bar nut that holds the clutch cover and
chain brake. Use the combination spanner. Then
retighten the bar nut as tightly as you can by hand.
(27)
• Raise the tip of the bar and stretch the chain by
tightening the chain tensioning screw using the
combination spanner. Tighten the chain until it does
not sag from the underside of the bar. (28)
• Use the combination spanner to tighten the bar nut
while holding up the tip of the bar. Check that you can
pull the saw chain round freely by hand, and that there
is no slack on the underside of the bar.
(29)
The position of the chain tensioning screw on our chain
saws varies from model to model. See instructions under
the heading What is what? to find out where it is on your
model.
445e II, 450e II
• Release the knob by folding it out. (30)
• Turn the knob anti clockwise to loosen the bar cover.
(31)
• Adjust the tension on the chain by turning the wheel
down (+) for tighter tension and up (-) to loosen the
tension.
(32)
• Tighten the bar clutch by turning the knob clockwise.
(33)
• Fold the knob back in to lock the tensioning. (34)
Lubricating cutting equipment
Chain oil
Chain oil must demonstrate good adhesion to the chain
and also maintain its flow characteristics regardless of
whether it is warm summer or cold winter weather.
As a chain saw manufacturer we have developed an
optimal chain oil which, with its vegetable oil base, is also
biodegradable. We recommend the use of our own oil for
both maximum chain life and to minimise environmental
damage. If our own chain oil is not available, standard
chain oil is recommended.
Never use waste oil! Using waste oil can be dangerous
to you and damage the machine and environment.
Filling with chain oil
• All our chain saws have an automatic chain lubrication
system. On some models the oil flow is also
adjustable.
• The saw chain oil tank and the fuel tank are designed
so that the fuel runs out before the saw chain oil.
However, this safety feature requires that you use the
right sort of chain oil (if the oil is too thin it will run out
before the fuel), and that you adjust the carburetor as
recommended (a lean mixture may mean that the fuel
lasts longer than the oil) and that you also use the
recommended cutting equipment (a bar that is too
long will use more chain oil).
Checking chain lubrication
• Check the chain lubrication each time you refuel. See
instructions under the heading Lubricating the bar tip
sprocket.
Aim the tip of the bar at a light coloured surface about
20 cm (8 inches) away. After 1 minute running at 3/4
throttle you should see a distinct line of oil on the light
surface.
If the chain lubrication is not working:
• Check that the oil channel in the bar is not obstructed.
Clean if necessary.
(35)
• Check that the groove in the edge of the bar is clean.
Clean if necessary.
(36)
• Check that the bar tip sprocket turns freely and that
the lubricating hole in the tip sprocket is not blocked.
Clean and lubricate if necessary.
(37)
If the chain lubrication system is still not working after
carrying out the above checks and associated measures
you should contact your service agent.
Chain drive sprocket
The clutch drum is fitted with one of the following drive
sprockets:
A Spur sprocket (the chain sprocket is welded on the
drum)
B Rim sprocket (replaceable) (38)
!
WARNING! Poor lubrication of cutting
equipment may cause the chain to snap,
which could lead to serious, even fatal
injuries.
IMPORTANT! When using vegetable based saw chain
oil, dismantle and clean the groove in the bar and saw
chain before long-term storage. Otherwise there is a risk
of the saw chain oil oxidizing, which will result in the saw
chain becoming stiff and the bar tip sprocket jamming.