YTH2348 Owner's Manual / 96045000504 / 2008-11
SAFETY RULES Safe Operation Practices for Ride-On Mowers DANDER: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. • • WARNING: In order to prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug.
SAFETY RULES Safe Operation Practices for Ride-On Mowers III. CHILDREN GENERAL SERVICE • Never operate machine in a closed area. • Keep all nuts and bolts tight to be sure the equipment is in safe working condition. • Never tamper with safety devices. Check their proper operation regularly. • Keep machine free of grass, leaves, or other debris build-up. Clean oil or fuel spillage and remove any fuelsoaked debris. Allow machine to cool before storing.
PRODUCT SPECIFICATIONS Gasoline Capacity and type: 3 Gallons Unleaded Regular Oil Type (API-SG-SL): SAE 30 (above 32°F) SAE 5W-30 (below 32°F) Oil Capacity: w/Filter: w/o Filter: Spark Plug: Champion QC12YC (Gap: .040") Ground Speed (MPH): Forward: Reverse: Charging System: 16 AMPS @ 3600 RPM Battery: AMP/HR: MIN. CCA: Case Size: Blade Bolt Torque: 45-55 FT. LBS. CUSTOMER RESPONSIBILITIES • • • 64 oz 60 oz Read and observe the safety rules.
UNASSEMBLED PARTS Slope Sheet Key (1) Oil Drain Tube (2) Keys ASSEMBLY Your new tractor has been assembled at the factory with the exception of those parts left unassembled for shipping puposes. When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel). ADJUST SEAT (See Fig. 2) • • TO REMOVE TRACTOR FROM CARTON • Sit in seat.
ASSEMBLY ✓CHECKLIST CHECK TIRE PRESSURE The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance. • Reduce tire pressure to PSI shown on tires. BEFORE YOU OPERATE YOUR NEW TRACTOR, WE WISH TO ASSURE THAT YOU RECEIVE THE BEST PERFORMANCE AND SATISFACTION FROM THIS QUALITY PRODUCT. PLEASE REVIEW THE FOLLOWING CHECKLIST: ✓ All assembly instructions have been completed. ✓ No remaining loose parts in carton.
OPERATION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning.
OPERATION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference. P H D E G K L B F C J A M FIG. 3 Our tractors conform to the applicable safety standards of the American National Standards Institute. (H) LIGHT SWITCH – Turns the headlights on and off.
OPERATION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend standard safety glasses or a wide vision safety mask worn over spectacles. HOW TO USE YOUR TRACTOR IMPORTANT: Leaving the ignition switch in any position other than "STOP" will cause the battery to discharge and go dead.
OPERATION TO ADJUST GAUGE WHEELS (See Fig. 9) Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions. J NOTE: Adjust gauge wheels with tractor on a flat level surface. • Adjust mower to desired cutting height (See “TO ADJUST MOWER CUTTING HEIGHT” in this section of manual).
OPERATION TO TRANSPORT (See Figs. 3 and 11) S When pushing or towing your tractor, be sure to disengage transmission by placing freewheel control in freewheeling position. Free wheel control is located at the rear drawbar of tractor. • Raise attachment lift to highest position with attachment lift control. • Pull freewheel control out and down into the slot and release so it is held in the disengaged position. • Do not push or tow tractor at more than two (2) MPH.
OPERATION TO START ENGINE (See Fig. 3) BEFORE STARTING THE ENGINE When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine. • Be sure freewheel control is in the transmission engaged position. • Sit on seat in operating position, depress brake pedal and set parking brake. • Move attachment clutch to “DISENGAGED” position. • Move throttle control to choke position.
OPERATION MOWING TIPS PURGE TRANSMISSION • CAUTION: Never engage or disengage freewheel lever while the engine is running. • • To ensure proper operation and performance, it is recommended that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have developed during shipping of your tractor.
MAINTENANCE MAINTENANCE SCHEDULE BEFORE EACH USE EVERY 8 HOURS EVERY 25 HOURS EVERY 50 HOURS EVERY 100 HOURS EVERY SEASON BEFORE STORAGE Check Brake Operation Check Tire Pressure T Check Operator Presence & ROS Systems R A Check for Loose Fasteners C Check/Replace Mower Blades T Lubrication Chart 0 Check Battery Level R Clean Battery and Terminals 3 4 Check Transaxle Cooling Check Mower Levelness Check V-Belts Check Engine Oil Level Change Engine Oil (with oil filter) 1,2 Change Engine Oil (wi
MAINTENANCE TRACTOR BLADE CARE Always observe safety rules when performing any maintenance. For best results mower blades must be sharp. Replace worn, bent or damaged blades. BRAKE OPERATION If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced. (See “TO CHECK BRAKE” in the Service and Adjustments section of this manual).
MAINTENANCE NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, they will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil. Change the oil after every 50 hours of operation or at least once a year if the tractor is not used for 50 hours in one year. Check the crankcase oil level before starting the engine and after each eight (8) hours of operation.
MAINTENANCE AIR FILTER DECK WASHOUT PORT (See Fig. 17) Your engine will not run properly using a dirty air filter. Service air cleaner more often under dusty conditions. See Engine Manual. Your tractor’s deck is equipped with a washout port on its surface as part of its deck wash system. It should be utilized after each use. 1. Drive the tractor to a level, clear spot on your lawn, near enough to a water spigot for your garden hose to reach.
SERVICE AND ADJUSTMENTS WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: • Depress brake pedal fully and set parking brake. • Place attachment clutch in “DISENGAGED” position. • Turn ignition key to “STOP” and remove key. • Make sure the blades and all moving parts have completely stopped. • Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. TO REMOVE MOWER (See Fig.
SERVICE AND ADJUSTMENTS - - Pivot bar towards you and insert other end of bar into hole in rear mower bracket (D). Move mower as needed to insert bar. Secure with washer and retainer spring as shown. D 02965 FIG. 19 FIG. 22 • 02 05 1 • ATTACH MOWER SIDE SUSPENSION ARMS (A) TO CHASSIS - Position hole in arm over pin (B) on outside of tractor chassis and secure with washer and retainer spring. Repeat on opposite side of tractor. A A 02965 B FIG.
SERVICE AND ADJUSTMENTS • ATTACH FRONT LINK (E) - Work from left side of tractor. Insert rod end of link assembly through front hole in tractor front suspension bracket (F) and secure with retainer spring (G) through hole in link located behind the bracket. E F H M J G FIG. 26 • Engage belt tension rod (K) on locking bracket (L). FIG. 25 • CAUTION: Belt tension rod is spring loaded. Have a tight grip on rod and engage slowly.
SERVICE AND ADJUSTMENTS TO LEVEL MOWER • If adjustment is necessary, see steps in Visual Adjustment instructions above. • Recheck measurements, adjust if necessary until both sides are equal. FRONT-TO-BACK ADJUSTMENT (See Figs. 30 and 31) IMPORTANT: Deck must be level side-to-side. To obtain the best cutting results, the mower blades should be adjusted so the front tip is 1/8" to 1/2" lower than the rear tip when the mower is in its highest position.
SERVICE AND ADJUSTMENTS TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 32) MOWER DRIVE BELT INSTALLATION • Install belt around all mandrel pulleys (R) and around idler pulleys (V) as shown. • Install belt onto electric clutch pulley (M). IMPORTANT: Check belt for proper routing in all mower pulley grooves. • Reassemble mandrel covers (Q). Securely tighten all screws. • Engage belt tension rod (K) on locking bracket (L). MOWER DRIVE BELT REMOVAL • Park tractor on a level surface. Engage parking brake.
SERVICE AND ADJUSTMENTS BELT INSTALLATION • Install new belt from tractor rear to front, over the steering plate (H) and above clutch brake pedal shaft (J). • Pull belt toward front of tractor and roll belt around electric clutch and onto engine pulley (G). • Pull belt toward rear of tractor. Carefully work belt down around transmission cooling fan and onto the input pulley (F). Be sure belt is inside the belt keeper. • Install belt on centerspan idler (E).
SERVICE AND ADJUSTMENTS REPLACING BATTERY (See Fig. 36) WARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from accidental grounding. • Lift hood to raised position. • Disconnect BLACK battery cable (A) then RED battery cable and carefully remove battery from tractor.
SERVICE AND ADJUSTMENTS ENGINE TO REPLACE FUSE Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash. TO ADJUST THROTTLE CONTROL CABLE The throttle control has been preset at the factory and adjustment should not be necessary. If adjustment is necessary, see engine manual. TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 37) • • • • Raise hood. Unsnap headlight wire connector. Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.
STORAGE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. ENGINE FUEL SYSTEM IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS DURING STORAGE.
TROUBLESHOOTING POINTS PROBLEM CAUSE CORRECTION Will not start 1. 2. 3. 4. 5. 6. 7. 8. 1. 2. 3. 4. 5. 6. 7. 8. Out of fuel. Engine not “CHOKED” properly. Engine flooded. Bad spark plug. Weak or dead battery. Dirty air filter. Dirty fuel filter. Water in fuel. 9. 10. Loose or damaged wiring. Carburetor out of adjustment. 9. 10. 11. Engine valves out of adjustment. 11. Fill fuel tank. See “TO START ENGINE” in Operation section. Wait several minutes before attempting to start. Replace spark plug.
TROUBLESHOOTING POINTS PROBLEM CAUSE CORRECTION Engine dies when tractor is shifted into reverse 1. 1. Turn ignition key to ROS "ON" position. See Operation section. Reverse operation system (ROS) is not "ON" while mower or other attachment is engaged. Engine continues to run when operator leaves seat with attachment clutch engaged 1. Faulty operator-safety presence control system. 1. Check wiring, switches and connections. If not corrected, contact an authorized service center/ department.
TRACTOR - MODEL NO. YTH2348 (96045000504), PRODUCT NO.
TRACTOR - MODEL NO. YTH2348 (96045000504), PRODUCT NO.
TRACTOR - MODEL NO. YTH2348 (96045000504), PRODUCT NO. 960 45 00-05 ELECTRICAL KEY NO. PART NO.
TRACTOR - MODEL NO. YTH2348 (96045000504), PRODUCT NO.
TRACTOR - MODEL NO. YTH2348 (96045000504), PRODUCT NO. 960 45 00-05 CHASSIS KEY NO. PART NO.
TRACTOR - MODEL NO. YTH2348 (96045000504), PRODUCT NO.
TRACTOR - MODEL NO. YTH2348 (96045000504), PRODUCT NO. 960 45 00-05 DRIVE KEY NO. PART NO.
TRACTOR - MODEL NO. YTH2348 (96045000504), PRODUCT NO.
TRACTOR - MODEL NO. YTH2348 (96045000504), PRODUCT NO. 960 45 00-05 ENGINE KEY NO. PART NO.
TRACTOR - MODEL NO. YTH2348 (96045000504), PRODUCT NO. 960 45 00-05 SEAT ASSEMBLY 1 8 8 7 7 8 41 8 40 10 6 21 37 37 44 2 43 21 3 seat-tex_6.5SL_2 KEY NO. PART NO. DESCRIPTION 1 2 3 6 7 8 10 21 532 40 66-21 532 18 01-66 532 14 06-75 873 80 06-00 532 12 41-81 532 17 18-77 532 19 69-77 532 17 18-52 Seat Bracket Pivot Fender Strap, Asm Fender Nut, Lock w/Ins. 3/8-16 unc Spring, Seat Cprsn Bolt 5/16-18 unc x 3/4 w/Sems Pan, Seat Bolt, Shoulder 5/16-18 KEY NO. PART NO.
TRACTOR - MODEL NO. YTH2348 (96045000504), PRODUCT NO. 960 45 00-05 STEERING ASSEMBLY 26 45 51 1 21 63 19 16 60 57 63 9 61 8 7 66 67 2 59 98 7 6 4 35 58 64 67 28 13 15 22 6 14 5 69 68 62 13 14 15 53 8 70 steering-tex_4-husq 13 KEY NO. 1 2 4 5 6 7 8 9 13 14 15 16 19 21 22 26 28 35 45 PART NO.
TRACTOR - MODEL NO. YTH2348 (96045000504), PRODUCT NO.
TRACTOR - MODEL NO. YTH2348 (96045000504), PRODUCT NO. 960 45 00-05 MOWER DECK KEY NO. PART NO.
TRACTOR - MODEL NO. YTH2348 (96045000504), PRODUCT NO. 960 45 00-05 MOWER LIFT 7 87 87 90 98 89 3 10 88 97 2 91 97 91 87 89 lift-tex_3 89 87 KEY NO. 2 3 7 10 87 88 89 PART NO. 532 19 52-23 532 19 52-31 532 41 15-55 532 19 63-14 532 19 42-09 532 41 07-10 819 19 19-12 KEY NO. DESCRIPTION Shaft Asm., Lift Lever Asm., Lift Grip, Lever Spring Torsion Pin Cotter 7/16 Bow Tie Lock Spring Lift Assist Washer Clear Zinc 90 91 97 98 PART NO.
TRACTOR - MODEL NO. YTH2348 (96045000504), PRODUCT NO. 960 45 00-05 DECALS 16 15 17 16 4 1 14 14 8 9 6 5 2 KEY NO. 1 2 4 5 6 8 9 14 15 PART NO. 532 41 91-38 532 42 38-30 532 19 15-54 532 17 84-55 532 40 88-41 532 19 87-85 532 14 50-05 532 41 00-55 532 18 09-41 DESCRIPTION Decal, Operator's Decal, Ethanol E85 Decal, Fender Decal, Caution Decal, Eng. HP Decal, Mower Sch. Decal, Battery Dnge/Poi Decal, Panel Side Decal, Cust. Resp. WHEELS AND TIRES 1 2 11 3 4 7 10 5 6 9 8 KEY NO.
SERVICE NOTES 44
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION FOL DA L O NG D THIS O I T S T A E D LIN 1 5 DEG E RE E S LOP E ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL 15 DEGREES MAX. WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than 15 degrees. Make turns gradually to prevent tipping or loss of control. Exercise extreme caution when changing direction on slopes. 1. Fold this page along dotted line indicated above. 2.
SERVICE NOTES 46
SERVICE NOTES 47
532 42 47-61 Rev. 1 11-21-08 BAD Printed in U.S.A.
