Operators Manual
Table Of Contents
- Contents
- Introduction
- Safety
- Assembly
- Introduction
- To attach the throttle handle
- To assemble the handlebar
- To set the handlebar in transport position
- To assemble the cutting equipment
- To attach the guard extension
- To remove the guard extension
- To attach the grass blade and the grass blade guard/combination guard
- To attach the saw blade guard on 545FX, 545FXT and 545F
- To attach the saw blade guard 545FR, 545RX, 545RXT
- To attach the saw blade
- To attach the trimmer guard or combination guard for trimmer head and plastic blades
- To attach a trimmer head or plastic blade
- To adjust the Balance X harness 545FR, 545RX
- To adjust the Balance XT harness
- Operation
- Introduction
- Before you operate the product
- Fuel
- Work position
- Correct balance of the product
- To start a cold engine
- To start a warm engine (545F, 545FX, 545FXT)
- To start a warm engine (545FR, 545RX, 545RXT)
- To stop the engine
- Heated handles
- Blade thrust
- General work instructions
- Forestry clearing with a saw blade
- Brush cutting with a saw blade
- Grass clearing with a grass blade
- Grass trimming with a trimmer head
- Maintenance
- Introduction
- Maintenance schedule
- To adjust the idle speed
- To adjust the start throttle speed (545FR, 545RX, 545RXT)
- To clean the muffler
- To clean the cooling system and starter pawls
- Air filter
- Bevel gear
- Drive shaft
- To attach and remove the locknut
- To sharpen the grass knife and grass blade
- To sharpen the saw blade
- To examine the spark plug
- To adjust the product for cold environments
- To lubricate the wire
- Troubleshooting
- Transportation and storage
- Technical data
- Accessories
- EC Declaration of Conformity
To attach the saw blade guard 545FR, 545RX,
545RXT
1. Attach the holder (A) and bracket (B) with 2 bolts (C)
on the gear housing (D).
2. Attach the saw blade guard (E) with 4 bolts (F) in the
holder (A).
B
C
D
F
A
E
To attach the saw blade
1. Put the drive disc (A) on the output shaft.
2. Turn the output shaft to align one of the holes in the
drive disc with the related hole in the gear housing.
3. Put the locking pin (B) in the hole to lock the shaft.
4. Put the saw blade (C) and the support flange (D) on
the output shaft.
D
E
C
A
B
5. Make sure that the drive disc and support flange
engages correctly in the center hole of the grass
blade.
6. Attach the nut (E).
7. Tighten the nut with the socket wrench. Hold the
shaft of the socket wrench near the blade guard.
Tighten in the opposite direction to how the cutting
attachment rotates. Tighten it to a torque of 35-50
Nm.
To attach the trimmer guard or combination
guard for trimmer head and plastic blades
1. Hang the trimmer guard/combination guard (A) onto
the two hooks on the plate holder (M).
2. Bend the guard around the shaft and attach it with
the bolt (L) on the opposite side of the shaft.
3. Put the locking pin (C) in the groove on the bolt head
and tighten the bolt fully.
L
A
M
C
To attach a trimmer head or plastic blade
1. Put the drive disc (B) on the output shaft.
2. Align the metal cup (P) with the center of the blade
guide on the drive disc.
3. Turn the output shaft to align one of the holes in the
drive disc with the related hole in the gear housing.
4. Put the locking pin (C) in the hole to lock the shaft.
5. Turn the trimmer head/plastic blades (H)
counterclockwise to attach.
B
H
P
C
12
1018 - 003 - 20.11.2019