Operators Manual
Table Of Contents
- Contents
- Introduction
- Safety
- Assembly
- Introduction
- To attach the throttle handle
- To assemble the handlebar
- To set the handlebar in transport position
- To assemble the cutting equipment
- To attach the guard extension
- To remove the guard extension
- To attach the grass blade and the grass blade guard/combination guard
- To attach the saw blade guard on 545FX, 545FXT and 545F
- To attach the saw blade guard 545FR, 545RX, 545RXT
- To attach the saw blade
- To attach the trimmer guard or combination guard for trimmer head and plastic blades
- To attach a trimmer head or plastic blade
- To adjust the Balance X harness 545FR, 545RX
- To adjust the Balance XT harness
- Operation
- Introduction
- Before you operate the product
- Fuel
- Work position
- Correct balance of the product
- To start a cold engine
- To start a warm engine (545F, 545FX, 545FXT)
- To start a warm engine (545FR, 545RX, 545RXT)
- To stop the engine
- Heated handles
- Blade thrust
- General work instructions
- Forestry clearing with a saw blade
- Brush cutting with a saw blade
- Grass clearing with a grass blade
- Grass trimming with a trimmer head
- Maintenance
- Introduction
- Maintenance schedule
- To adjust the idle speed
- To adjust the start throttle speed (545FR, 545RX, 545RXT)
- To clean the muffler
- To clean the cooling system and starter pawls
- Air filter
- Bevel gear
- Drive shaft
- To attach and remove the locknut
- To sharpen the grass knife and grass blade
- To sharpen the saw blade
- To examine the spark plug
- To adjust the product for cold environments
- To lubricate the wire
- Troubleshooting
- Transportation and storage
- Technical data
- Accessories
- EC Declaration of Conformity
7. Handle adjustment
8. Throttle trigger
9. Stop switch
10. Start throttle button
11. Throttle trigger lockout
12. Throttle wire adjustment
13. Suspension point
14. Fuel tank
15. Decompression valve
16. Muffler
17. Spark plug cap and spark plug, below the cover
18. Starter rope handle
19. Air purge bulb
20. Air filter cover
21. Choke control
22. Harness, safety-release mechanism
23. Harness, hip pad
24. Drive disc
25. Cutting attachment guard
26. Locknut
27. Support flange
28. Handlebar
29. Support cup
30. Transport guard
31. Locking pin
32. Operator's manual
33. Socket wrench
Symbols on the product
Be careful and use the product correctly.
This product can cause serious injury or
death to the operator or others.
Read the operator's manual carefully and
make sure that you understand the
instructions before use.
Use a protective helmet in locations where
objects can fall on you. Use approved
hearing protection. Use approved eye
protection.
Maximum speed of the output shaft.
The product agrees with the applicable EC
directives.
The product can cause objects to eject,
which can cause injury.
5
0
FT
1
5
m
50F
T
15 m
Keep a minimum distance of 15 m/49 ft to
persons and animals during operation of the
product.
Risk of blade thrust if the cutting equipment
touches an object that it does not
immediately cut. The product can cut off
body parts. Keep a minimum of 15 m / 49 ft
distance to persons and animals during
operation of the product.
Use approved protective gloves.
Use heavy-duty slip-resistant boots.
Air purge bulb.
Choke.
Fuel.
Decompression valve.
Heated handles.
Only use a flexible cutting wire. Do not use
metal cutting attachments. Apply this for
grass guard accessory.
Sound power level.
yyyywwxxxx The rating plate shows the
serial number. yyyy is the
production year and ww is
the production week.
1018 - 003 - 20.11.2019 3