Operators Manual
Table Of Contents
- Contents
- Introduction
- Safety
- Assembly
- Introduction
- To attach the throttle handle
- To assemble the handlebar
- To set the handlebar in transport position
- To assemble the cutting equipment
- To attach the guard extension
- To remove the guard extension
- To attach the grass blade and the grass blade guard/combination guard
- To attach the saw blade guard on 545FX, 545FXT and 545F
- To attach the saw blade guard 545FR, 545RX, 545RXT
- To attach the saw blade
- To attach the trimmer guard or combination guard for trimmer head and plastic blades
- To attach a trimmer head or plastic blade
- To adjust the Balance X harness 545FR, 545RX
- To adjust the Balance XT harness
- Operation
- Introduction
- Before you operate the product
- Fuel
- Work position
- Correct balance of the product
- To start a cold engine
- To start a warm engine (545F, 545FX, 545FXT)
- To start a warm engine (545FR, 545RX, 545RXT)
- To stop the engine
- Heated handles
- Blade thrust
- General work instructions
- Forestry clearing with a saw blade
- Brush cutting with a saw blade
- Grass clearing with a grass blade
- Grass trimming with a trimmer head
- Maintenance
- Introduction
- Maintenance schedule
- To adjust the idle speed
- To adjust the start throttle speed (545FR, 545RX, 545RXT)
- To clean the muffler
- To clean the cooling system and starter pawls
- Air filter
- Bevel gear
- Drive shaft
- To attach and remove the locknut
- To sharpen the grass knife and grass blade
- To sharpen the saw blade
- To examine the spark plug
- To adjust the product for cold environments
- To lubricate the wire
- Troubleshooting
- Transportation and storage
- Technical data
- Accessories
- EC Declaration of Conformity
3. Push the air purge bulb (C) about 6 times or fuel until
fuel starts to fill the bulb. It is not necessary to fill the
air bulb fully.
C
B
A
4. Hold the body of the product on the ground with your
left hand.
CAUTION: Do not step on the product.
5. Pull the starter rope handle slowly until you feel
some resistance. When you feel resistance, pull the
starter rope handle quickly and with force.
Note:
Do not twist the starter rope around your hand.
6. Continue pull the starter rope handle until the engine
starts.
CAUTION:
Do not pull the starter rope to
full extension and do not let go of the
starter rope handle. Release the starter
rope slowly. If you do not obey these
instructions it can cause damage to the
engine.
7. Set the choke control to the run position and apply
full throttle.
To start a warm engine (545F, 545FX,
545FXT)
1. Set the stop switch (A) to the start position.
2. Pull the choke control (B) up.
3. Set the throttle trigger (C) to the start position.
4. Push the air purge bulb (D) 10 times. It is not
necessary to fill the air purge bulb fully.
D
A
E
C
B
Note: Do not use the decompression valve (E).
5. Pull the starter rope handle quickly and with force.
Pull the starter rope handle until the engine fires.
To start a warm engine (545FR,
545RX, 545RXT)
1. Set the stop switch (A) to the start position.
2. Push the throttle lockout (B) and the throttle trigger
(C).
3. Push the start throttle button (D) while you engage
the throttle trigger (C).
4. Release the throttle lockout and the throttle trigger.
5. Push the air purge bulb (E) 10 times. It is not
necessary to fill the air purge bulb fully.
E
D
B
F
A
C
Note:
Do not use the decompression valve (F).
6. Pull the starter rope handle quickly and with force.
Pull the starter rope handle until the engine fires.
To stop the engine
• Move the stop switch to the stop position.
1018 - 003 - 20.11.2019
17