Operators Manual
Table Of Contents
- Contents
- Introduction
- Safety
- Assembly
- Introduction
- To attach the throttle handle
- To assemble the handlebar
- To set the handlebar in transport position
- To assemble the cutting equipment
- To attach the guard extension
- To remove the guard extension
- To attach the grass blade and the grass blade guard/combination guard
- To attach the saw blade guard on 545FX, 545FXT and 545F
- To attach the saw blade guard 545FR, 545RX, 545RXT
- To attach the saw blade
- To attach the trimmer guard or combination guard for trimmer head and plastic blades
- To attach a trimmer head or plastic blade
- To adjust the Balance X harness 545FR, 545RX
- To adjust the Balance XT harness
- Operation
- Introduction
- Before you operate the product
- Fuel
- Work position
- Correct balance of the product
- To start a cold engine
- To start a warm engine (545F, 545FX, 545FXT)
- To start a warm engine (545FR, 545RX, 545RXT)
- To stop the engine
- Heated handles
- Blade thrust
- General work instructions
- Forestry clearing with a saw blade
- Brush cutting with a saw blade
- Grass clearing with a grass blade
- Grass trimming with a trimmer head
- Maintenance
- Introduction
- Maintenance schedule
- To adjust the idle speed
- To adjust the start throttle speed (545FR, 545RX, 545RXT)
- To clean the muffler
- To clean the cooling system and starter pawls
- Air filter
- Bevel gear
- Drive shaft
- To attach and remove the locknut
- To sharpen the grass knife and grass blade
- To sharpen the saw blade
- To examine the spark plug
- To adjust the product for cold environments
- To lubricate the wire
- Troubleshooting
- Transportation and storage
- Technical data
- Accessories
- EC Declaration of Conformity
Approved accessories Accessory type Cutting attachment guard, art. no.
Plastic blades Tricut Ø 300 mm (Separate blades
have part number 531 01 77-15)
537 28 85-01 / 544 46 43-01
Trimmer head Trimmy S II (Ø 2.4–3.3 mm cord) 503 95 43-01 / 544 46 43-01
Auto 55 (Ø 2.7-3.3 mm cord) 503 95 43-01 / 544 46 43-01
T45x (Ø 2.7–3.3 mm cord) 503 95 43-01 / 544 46 43-01
Support cup Fixed
Shredder blade 544 02 65-02
Accessories for 545F 545FX, 545FXT
Approved accessories
Accessory type Cutting attachment guard, art. no.
Centre hole in blades/knives, Ø 25.4
mm
Output shaft thread M12
Grass blade/grass knife Multi 255-3 (Ø 255, 3 teeth) 537 29 74-01 / 544 46 43-01
Multi 275-4 (Ø 275, 4 teeth) 537 29 74-01 / 544 46 43-01
Multi 300-3 (Ø 300 3 teeth) 537 29 74-01 / 544 46 43-01
Saw blade Maxi 200-26 (Ø 200, 26 teeth) 574 53 26-01
Scarlet 200-22 (Ø 200, 22 teeth) 574 53 26-01
Scarlet 225-24 (Ø 225, 24 teeth) 574 50 67-02
Maxi 225-24T BACHO (Ø 225, 24
teeth)
574 50 67-02
Plastic blades Tricut Ø 300 mm (Separate blades
have part number 531 01 77-15)
537 29 74-01 / 544 46 43-01
Trimmer head Trimmy S II (Ø 2.4–3.3 mm cord) 537 29 73-01 / 544 46 43-01
Auto 55 (Ø 2.7-3.3 mm cord) 537 29 73-01 / 544 46 43-01
T45x (Ø 2.7–3.3 mm cord) 537 29 73-01 / 544 46 43-01
T55x (Ø 2.7–3.3 mm cord) 537 29 73-01 / 544 46 43-01
Support cup Fixed
Accessories for 545RX, 545RXT
Approved accessories
Accessory type Cutting attachment guard, art. no.
Centre hole in blades/knives, Ø 25.4
mm
Output shaft thread M12
1018 - 003 - 20.11.2019 31