Operators Manual
Table Of Contents
- Symbols
- Contents
- Note the following before starting:
- Dear Customer,
- Important
- Personal protective equipment
- Machine¢s safety equipment
- Cutting equipment
- Assembling the handlebar and throttle
- Fitting blades and trimmer heads
- Fitting the transport guard
- Adjusting the harness and brush cutter
- Fuel safety
- Fuel
- Fueling
- Check before starting
- Starting and stopping
- General working instructions
- Carburettor
- Air filter
- Fuel filter
- Bevel gear
- Spark plug
- Trouble shooting
- Maintenance schedule
- Technical data
- EC Declaration of Conformity
- Símbolos
- Índice
- Antes de arrancar, observe lo siguiente:
- Apreciado cliente:
- Importante
- Equipo de protección personal
- Equipo de seguridad de la máquina
- Equipo de corte
- Montaje del manillar y la empuñadura de acelerador
- Montaje de la hoja y del cabezal de corte
- Montaje de la protección para transportes
- Ajuste del arnés y la desbrozadora
- Seguridad en el uso del combustible
- Carburante
- Repostaje
- Control antes de arrancar
- Arranque y parada
- Instrucciones generales de trabajo
- Carburador
- Filtro de aire
- Filtro de combustible
- Engranaje angulado
- Bujía
- Localización de averías
- Programa de mantenimiento
- Datos técnicos
- Declaración CE de conformidad
- Símbolos
- Índice
- Antes de arrancar, observe o seguinte:
- Prezado cliente!
- Importante
- Equipamento de protecção pessoal
- Equipamento de segurança da máquina
- Equipamento de corte
- Montagem da direcção e do punho do acelerador
- Montagem da lâmina e cabeçote de recorte
- Montagem da protecção para transporte
- Ajuste do suporte e do roçador
- Segurança no manejo de combustível
- Combustível
- Abastecimento
- Controlo antes de arrancar
- Arranque e paragem
- Instruções gerais de trabalho
- Carburador
- Filtro de ar
- Filtro de combustível
- Engrenagem angular
- Vela de ignição
- Localização de avarias
- Esquema de manutenção
- Especificações técnicas
- Certificado CE de conformidade
- Simboli
- Indice
- Prima dell’avviamento osservare quanto segue:
- Alla gentile clientela
- Importante
- Abbigliamento protettivo
- Attrezzatura di taglio
- Montaggio del manubrio e impugnatura dell'acceleratore
- Montaggio della lama e della testina portafilo
- Montaggio della protezione per il trasporto
- Come indossare l’imbracatura ed agganciare il decespugliatore
- Carburante
- Carburante
- Rifornimento
- Controlli prima dell’avviamento
- Avviamento e arresto
- Istruzioni generali di lavoro
- Carburatore
- Filtro dell’aria
- Filtro del carburante
- Riduttore angolare
- Candela
- Ricerca dei guasti
- Schema di manutenzione
- Caratteristiche tecniche
- Dichiarazione di conformità CE
- Blank Page
ASSEMBLY
English – 13
The guard extension is removed easily using a
screwdriver, see illustration.
Fitting a blade guard, grass blade and
grass cutter
• Hook the blade guard/combination guard (A) onto the
fitting on the shaft and secure with the bolt (L). Use the
recommended blade guard. See the Technical data
section. CAUTION! Ensure that the guard extension is
removed.
(533RS)
(543RS, 553RS)
• Fit the drive disc (B) on the output shaft.
• Turn the output shaft until one of the holes in the drive
disc aligns with the corresponding hole in the gear
housing.
• Insert the locking pin (C) in the hole to lock the shaft.
• Place the blade (D), support cup (E) and support
flange (F) on the output shaft.
• Fit the nut (G). The nut must be tightened to a torque
of 35-50 Nm. Use the spanner in the tool kit. Hold the
shaft of the spanner as close to the blade guard as
possible. To tighten the nut, turn the spanner in the
opposite direction to the direction of rotation (Caution!
left-hand thread).
(533RS)
(543RS, 553RS)
A
A
B
C
A
L
G
F
D
B
C
A
E
G
E
D
F
B
C
H1158941-30,533-553RS,WestII.fm Page 13 Tuesday, July 4, 2017 8:19 AM