Operators Manual
Table Of Contents
- Contents
- Introduction
- Safety
- Assembly
- Introduction
- To attach the throttle handle
- To assemble the handlebar
- To set the handlebar in transport position
- To assemble the cutting equipment
- To attach the grass blade guard/combination guard and the grass blade (555FX, 555FXT)
- To attach the saw blade guard (555FX, 555FXT)
- To attach the saw blade guard (555RXT, 555FRM)
- To attach the saw blade
- To attach the shredder blade guard and the shredder blade (555RXT, 555FRM)
- To attach the trimmer guard or combination guard for trimmer head and plastic blades
- To attach a trimmer head or plastic blade
- To adjust the Balance XT harness
- Operation
- Introduction
- To do before you operate the product
- Fuel
- Work position
- Correct balance of the product
- To start a cold engine
- To start a warm engine
- To stop the engine
- Heated handles (555FXT)
- Blade thrust
- General work instructions
- Forestry clearing with a saw blade
- Brush cutting with a saw blade
- Grass clearing with a grass blade
- Grass trimming with a trimmer head
- Shredding with a shredder blade
- Maintenance
- Introduction
- Maintenance schedule
- Carburetor
- To adjust the start throttle speed (555RXT, 555FRM)
- To clean the muffler
- To clean the cooling system
- Air filter
- Bevel gear
- Drive shaft
- To attach and remove the locknut
- To sharpen the grass knife and grass blade
- To sharpen the saw blade
- To examine the spark plug
- To adjust the product for cold environments
- To lubricate the wire (555FXT)
- Troubleshooting
- Transportation and storage
- Technical data
- Accessories
- EC Declaration of Conformity
EC Declaration of Conformity
EC Declaration of Conformity
Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel:
+46-36-146500, declares that the brush cutters
Husqvarna 555FX, 555FXT, 555RXT, 555FRM with
serial numbers dating from 2016 onwards (the year is
clearly stated on the rating plate, followed by the serial
number), comply with the requirements of the
COUNCIL’S DIRECTIVE:
• of May 17, 2006 ”relating to machinery” 2006/42/EC
• of February 26, 2014 ”relating to electromagnetic
compatibility” 2014/30/EU
• of May 8, 2000 ”relating to the noise emissions in the
environment” 2000/14/EC. Conformity assessment
according to Annex V. For information relating to
noise emissions, refer to
Technical data on page 31
.
• of June 8, 2011 ”on the restriction of the use of
certain hazardous substances in electrical and
electronic equipment” 2011/65/EU.
The following standards have been applied:
EN ISO 12100:2010, EN ISO 11806-1:2011, ISO
14982:1998, CISPR 12:2007, EN 50581:2012
RISE SMP Svensk Maskinprovning AB, Box 7035,
SE-750 07 Uppsala, Sweden, has performed voluntary
type examination on behalf of Husqvarna AB. The
certificates are numbered: SEC/09/2176 - 555FX,
555FXT, SEC/09/2175 - 555RXT, 555FRM.
RISE SMP Svensk Maskinprovning AB has also verified
agreement with appendix V of the council’s directive
2000/14/EG. The certificates have the numbers:
01/164/062 - 555FX, 555FXT, 01/164/070 - 555RXT,
555FRM.
Huskvarna, 2016-03-30
Per Gustafsson, Development Manager (Authorized
representative for Husqvarna AB and responsible for
technical documentation)
34 1346 - 002 - 08.10.2019