Operators Manual
Table Of Contents
- Contents
- Introduction
- Safety
- Assembly
- Introduction
- To attach the throttle handle
- To assemble the handlebar
- To set the handlebar in transport position
- To assemble the cutting equipment
- To attach the grass blade guard/combination guard and the grass blade (555FX, 555FXT)
- To attach the saw blade guard (555FX, 555FXT)
- To attach the saw blade guard (555RXT, 555FRM)
- To attach the saw blade
- To attach the shredder blade guard and the shredder blade (555RXT, 555FRM)
- To attach the trimmer guard or combination guard for trimmer head and plastic blades
- To attach a trimmer head or plastic blade
- To adjust the Balance XT harness
- Operation
- Introduction
- To do before you operate the product
- Fuel
- Work position
- Correct balance of the product
- To start a cold engine
- To start a warm engine
- To stop the engine
- Heated handles (555FXT)
- Blade thrust
- General work instructions
- Forestry clearing with a saw blade
- Brush cutting with a saw blade
- Grass clearing with a grass blade
- Grass trimming with a trimmer head
- Shredding with a shredder blade
- Maintenance
- Introduction
- Maintenance schedule
- Carburetor
- To adjust the start throttle speed (555RXT, 555FRM)
- To clean the muffler
- To clean the cooling system
- Air filter
- Bevel gear
- Drive shaft
- To attach and remove the locknut
- To sharpen the grass knife and grass blade
- To sharpen the saw blade
- To examine the spark plug
- To adjust the product for cold environments
- To lubricate the wire (555FXT)
- Troubleshooting
- Transportation and storage
- Technical data
- Accessories
- EC Declaration of Conformity
555FX 555FXT 555RXT 555FRM
Equipped with shredder blade (origi-
nal)
- - - 103
Vibration levels
5
Equivalent vibration levels (a
hv,eq
) at handles, measured according to EN ISO 11806 and ISO 22867, m/s
2
:
Equipped with trimmer head (origi-
nal), left/right
- - 1.7/2.0 -
Equipped with grass blade (original),
left/right
- - 1.5/1.6 -
Equipped with saw blade (original),
left/right
2.1/2.3 2.1/2.3 - -
Equipped with shredder blade (origi-
nal)
- - - 2.0/1.5
Accessories
555FX, 555FXT
Approved accessories Accessory type Cutting attachment guard, art. no.
Center hole in blades/knives, Ø 25.4
mm
Output shaft thread M12
Grass blade/grass knife Multi 275-4 (Ø 275, 4 teeth) 502 46 49-01
Multi 300-3 (Ø 300 3 teeth) 502 46 49-01
Multi 350-3 (Ø 350, 3 teeth) 502 46 49-01
Saw blade Maxi 225-24 (Ø 225, 24 teeth) 544 01 65-01
Scarlet 200-22 (Ø 200, 22 teeth) 537 21 71-01
Scarlet 225-24 (Ø 225, 24 teeth) 544 01 65-01
Trimmer head Trimmy S II (Ø 2.4–3.3 mm cord) 502 46 50-01
Auto 55 (Ø 2.7-3.3 mm cord) 502 46 50-01
T45x (Ø 2.7–3.3 mm cord) 502 46 50-01
T55x (Ø 2.7–3.3 mm cord) 502 46 50-01
F55 (Ø 2.7–3.5 mm cord) 502 46 50-01
Support cup Fixed
5
Reported data for equivalent vibration level has a typical statistical dispersion (standard deviation) of 1 m/s
2
.
32 1346 - 002 - 08.10.2019