580 R, 580 RS, 580 RSE, 580 RSW, 600 C Owner’s Manual 606 00 02 98A 11/00 Printed in USA
CONTROLS AND FEATURES 1 12 11. Poignée du démarreur manuel 12. Commande de l’entraînement des roues (tondeuses autotractées) 13. Déflecteur à paillis Mulch 14. Commande des gaz (modèle professionnel) 15. Trous de réglage du guidon 16. Indicateur de vitesse 2 14 11 3 8 10 16 9 7 13 15 7 5 4 6 Figure 1 ENGLISH 1. Engine Control 2. Ignition Switch (Electric Start Models) 3. Speed Selector (Selfpropelled) 4. Primer (Briggs Engine) 5. Side Discharge Cover 6. Side Discharge Deflector 7.
TABLE OF CONTENTS Controls and Features . . . . . . . . . . . . . 3 Introduction . . . . . . . . . . . . . . . . . . . . . . 4 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Assembly . . . . . . . . . . . . . . . . . . . . . . . . 9 Operation . . . . . . . . . . . . . . . . . . . . . . . 10 Maintenance . . . . . . . . . . . . . . . . . . . . 14 Service and Adjustments . . . . . . . . . . Storage . . . . . . . . . . . . . . . . . . . . . . . . . Troubleshooting . . . . . . . . . . . . . . .
DISCLAIMER Husqvarna reserves the right to discontinue, make changes to, and add improvements upon its products at any time without public notice or obligation.The descriptions and specifications contained in this manual were in effect at printing. Equipment described within this manual may be optional. Some illustrations may not be applicable to your unit. SAFETY SAFETY ALERTS PRACTICES AND LAWS Look for these symbols to point out important safety precautions.
SAFETY DECALS AND LOCATIONS ALWAYS replace missing or damaged Safety Decals. Refer to Figure 3 for Safety Decal locations. 1 CAUTION • BAG IS SUBJECT TO WEAR AND DETERIORATION. • CHECK BAG FEQUENTLY, REPLACE WHEN NECESSARY. • Read the operator's manual. • Keep children and others away from unit while operating. • Never direct discharge toward other people. Thrown objects can cause injury. • Do not operate mower unless guards are in operating position or entire bagger is attached.
DO NOT pull mower backwards unless absolutely necessary. Look down and back before and while moving backwards. DO NOT start the engine or operate mower unless either the Side Discharge Opening Cover or the Side Discharge Deflector is installed. Keep the area of operation clear of all persons, children and pets. ALWAYS clear area before operation to avoid thrown objects. Stop mower if anyone enters the area. Keep safety devices or guards in place and functioning properly.
DO NOT make cutting height wheel adjustments while the engine is running. On self-propelled models, releasing wheel drive control must stop mower’s forward movement. If this feature fails to operate, disconnect spark plug wire and repair before using unit. Wheel drive must be disengaged when starting engine. Fuel is highly flammable and its vapors can explode. ONLY use approved fuel containers. • NO Smoking! • NO Sparks! • NO Flames! • Allow engine to cool before filling fuel tank.
ASSEMBLY TO REMOVE UNIT FROM CARTON 1. Cut off top of carton. 2. Remove front and rear inserts and literature pack. 3. Cut out back of carton and roll unit out. 4. Remove protective packaging materials. 1 2 3 OM0340 5 Lit er Paatur ck e OM0320 OM0311 OM0350 1. 2. 3. 4. 5. 6. Mower Unit Discharge Chute Grass Bag Grass Bag Frame Literature Pack Battery Charger (electric start models) 6 4 OM0560 OM0330 Figure 4 ASSEMBLY 1. Unfold and adjust handlebar. 2.
OPERATION CONTROLS AND FEATURES To change cutting height, move cutting height levers one notch at a time on each wheel until desired height of cut is obtained. (Figure 6) See Figures 1 and 6 for Controls and Features. Cutting Height Settings Chart WARNING: DO NOT attempt to start your engine at this time. Familiarize yourself with controls to see what they do and how they work. Thoroughly read and understand entire Operators Manual first.
OPTIONAL CONTROLS Speed Selector See Figures 1 and 6. Speed Selector is used to select variable forward travel speeds of mower. Cutting Height – Swivel Models CAUTION: On swivel wheel models, when mowing on slopes it is recommended that the linchpin be positioned through the swivel lock hole. If wheels are in the swivel position and control handles are released the mower may “free roll” downhill. Never mow on steep slopes.
FILLING FUEL TANK WARNING: EXPLOSIVE VAPORS and FLAMMABLE FUEL can result in serious injury or death. Handle fuel with care. ALWAYS use an approved fuel container. No Smoking! No Lighted Materials! No Open Flame! Allow engine to cool before maintenance. Gasoline is highly flammable and must be handled with care. Allow engine to cool several minutes before removing fuel tank cap. Never fill tank when engine is running or is hot from operation. DO NOT allow open flame, matches, or smoking in area.
STARTING AND SHUT OFF Mowing Tips See Figures 1, 4 and 6 for all Controls and Features. NOTE: Start engine on a hard level surface that is free of debris. CAUTION: On swivel wheel models, when mowing on slopes it is recommended that the linchpin be positioned through the swivel lock hole. If wheels are in the swivel position and control handles are released the mower may “free roll” downhill. Never mow on steep slopes. Manual Start 1. Check each item in Before Each Use in the Maintenance Schedule. 2.
MAINTENANCE Husqvarna Dealers will provide any service, parts or adjustments which may be required to keep your unit operating at peak efficiency. Should engine service be required, contact a Husqvarna dealer or an authorized engine manufacturer's service center. WARNING: Stop engine, wait for moving parts to stop, and remove wire from spark plug (keep wire away from plug to prevent accidental starting) before attempting any lubrication or maintenance procedures.
1. Loosen wing bolt and lift cover. Remove pre-cleaner and cartridge assembly. 2. Wash pre-cleaner in liquid detergent and water. Allow to dry thoroughly. Saturate pre-cleaner in oil (SAE #30). Squeeze to remove excess oil. Do not wring. Replace if extremely dirty or damaged. 3. Tap cartridge gently on a flat surface. Do not oil cartridge. Replace if extremely dirty or damaged. 4. Do not use petroleum solvents (kerosene) which will cause cartridge to deteriorate.
CHECK DRIVE BELT When lubricating for the first time, clean all components thoroughly before applying grease. Reapply grease to the lube fittings every 25 hours. NOTE: Linchpin must be in the swivel lock hole while lubricating. 1 2 2 1 4 3 OM0250 1. Blade 2. Cap Screw, Lock Washer & Flat Washer 3. Drive Belt 4. Idler 1. Grease Fitting 2. Swivel Lock Hole Figure 11 OM0180 Figure 12 Check drive belt for wear or damage. Replace belt if worn or damaged. See Service and Adjustments.
1 1 4 4 2 2 3 OM0550 3 OM0570 Robin Briggs & Stratton Intek OHV 1. Oil Fill Cap & Dipstick 2. Air Cleaner 3. Spark Plug & Wire 4. Fuel Cap & Tank Figure 13 CHECK ENGINE COOLING Engine is air cooled. Air must circulate freely around engine from Air Intake to cooling fins on cylinder head and block to prevent overheating. WARNING: HOT SURFACES can cause death or serious injury. DO NOT TOUCH parts which are hot from operation. ALWAYS allow parts to cool.
SERVICE AND ADJUSTMENTS SERVICE POSITION WARNING: ACCIDENTAL ENGINE START UP can cause death or serious injury. ALWAYS stop engine, remove key (electric start models), wait for moving parts to stop and remove wire from spark plug before adjusting or servicing. Place unit on a flat level surface. ALWAYS stop engine. Assure unit is secure and will not tip over. Strap and clamp onto bench if needed. CAUTION: Before unit is tipped up, remove enough fuel so that no spills will occur.
3. Charge for 24 to 48 hours (battery may be charged for up to 72 hours with no harmful effects). An engine run time of at least 8 hours is required to charge a fully discharged battery. To Remove Battery from Unit 1. Remove wing nuts from battery U-bolt. 2. Disconnect battery from wiring. ENGINE/BLADE CONTROL No slack To adjust engine/blade control: 1. Loosen cable nuts away from bracket. 4. Tighten lower cable nut to 1/ 8" (3mm) below bracket. Release zbend bracket. 1/8 (3mm” ) 5.
DRIVE BELT (Self propelled units) To remove drive belt: 1. Position right hand rear wheel Height Adjustment lever in first notch and left hand rear wheel Height Adjustment lever in third notch. This provides clearance between friction wheel and drive disk. 2. Remove belt from idler, drive disk and engine pulley. 3. Pull belt through opening under mower pan and over blade. 4. Check idler for free rotation of pulley and movement of pivot. 5. Reinstall drive belt in reverse order.
STORAGE WARNING: FLAMMABLE FUEL and its EXPLOSIVE VAPORS can cause death or serious injury. DO NOT store unit with fuel in the fuel tank inside a building where any ignition sources are present. Drain fuel outdoors away from any ignition source. Allow engine to cool before storing in any enclosure. Only use approved fuel containers. IMPORTANT: NEVER spray unit with water or store unit outdoors.
TROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTION Engine will not start 1. Fuel tank empty or low. 2. Spark plug wire loose or off. 3. Engine/brake control cable detached, broken, or not adjusted properly. 4. Battery discharged (electric start models). 1. Check fuel level. Fill tank if necessary. 2. Check connection. 3. Check engine/brake control cable. Adjust, repair or replace as necessary. 4. Charge battery or replace if necessary. Self-propelled drive does not engage. 1.
SPECIFICATIONS Model Number 601 10 00 24 601 10 00 20 601 10 00 21 601 10 00 22 601 10 00 23 Description 580 R 580 RS 580 RSE 580 RSW 600 C Length - in (cm) 61.5 (156) Height - in (cm) 38 (96,5) Width - in (cm) 23 (58,4) Actual Weight - lbs (kg) 81 (36,7) 97 (44,0) 102 (46,3) 105 (47,6) 118 (53.6) Cutting Width 21 (53,3) Cutting Height - in. (cm) 6 Positions: 1.00 - 3.25 (2,5 - 8,3) Engine, 4 cycle Briggs & Stratton Intek OHV Robin Engine Power Max - HP 4.37 (3,26) 5.
GB - 24 The following items are not covered by this warranty: (1) Normal customer maintenance items which become worn through normal regular use, including, but not limited to, belts, blades, blade adapters, bulbs, filters, guide bars, lubricants, rewind springs, saw chain, spark plugs, starter ropes and tines; (2) Natural discoloration of material due to ultraviolet light; (3) Engine and drive systems not manufactured by Husqvarna; these items are covered by the respective manufacturer’s warranty as provi
GB - 25
01194000A
