Operator’s Manual 924HV / 96193007000 Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine. The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty. 532 44 34-68 Please read the owner's manual carefully and make sure you understand the instructions before using the machine.
IMPORTANT Safe Operation Practices for Walk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury. WARNING: Snow throwers have exposed rotating parts, which can cause severe injury from contact, or from material thrown from the discharge chute. Keep the area of operation clear of all persons, small children and pets at all times including startup.
6. When cleaning, repairing or inspecting the snow thrower, stop the engine and make certain the collector/impeller and all moving parts have stopped. Disconnect the spark plug wire and keep the wire away from the plug to prevent someone from accidentally starting the engine. 7. Do not run the engine indoors, except when starting the engine and for transporting the snow thrower in or out of the building. Open the outside doors; exhaust fumes are dangerous. 8.
PARTS PACKED SEPARATELY IN CARTON (1) POWER CORD (198563) (1) MULTIWRENCH (180684) (6) SHEAR BOLTS 1/4-20 x 1-3/4 (192090) (3) RETAINER SPRINGS (169675) (6) LOCKNUTS 1/4-20 (73800400) (2) FLAT WASHERS SAFTEY IGNITION KEY (S) (422663) (2) CARRIAGE BOLTS 3/8-16 x 2.
ASSEMBLY / PRE-OPERATION INSTALL TRACTION DRIVE CONTROL ROD (See Figs. 3 and 4) The traction drive control rod is installed on the snow thrower. 1. Remove plastic tie securing rod to lower handle. 2. With top end of rod positioned under left side of control panel, push rod down and insert top end of rod into hole in drive control bracket. Secure with retainer spring. NOTE: The multi-wrench may be used for assembly of the chute rotator head to snow thrower and making adjustments to the skid plates.
ASSEMBLY / PRE-OPERATION INSTALL DISCHARGE CHUTE / CHUTE ROTATER HEAD (See Fig. 7) NOTE: The multi-wrench provided in your parts bag may be used to install the chute rotater head. 1. Place discharge chute assembly on top of chute base with discharge opening toward front of snow thrower. 2. Position chute rotater head over chute bracket. If necessary, rotate chute assembly to align square and pin on underside of chute rotater head with holes in chute bracket. 3.
ASSEMBLY / PRE-OPERATION INSTALL CHUTE DEFLECTOR REMOTE CONTROL (See Figs. 8 and 9) 1. Install remote cable bracket to discharge chute with 5/16-18 carriage bolt and 5/16-18 locknut as shown. Tighten securely. 2. Install remote cable eyelet to chute deflector with 1/4-20 shoulder bolt and 1/4-20 locknut as shown. Tighten nut securely. Cable eyelet will be loose on shoulder bolt. 3. Install spring hooks between hex nuts on chute rotater head and into hole in chute deflector as shown.
OPERATION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your snow thrower or in literature supplied with the product. Learn and understand their meaning.
OPERATION ELECTRIC START BUTTON MUFFLER GASOLINE FILLER CAP AUGER CONTROL LEVER POWER CORD PLUG CHOKE CONTROL DISCHARGE CHUTE CONTROL LEVER DRIVE SPEED CONTROL LEVER CHUTE DEFLECTOR SAFETY IGNITION KEY DEFLECTOR REMOTE CONTROL LEVER TRACTION DRIVE CONTROL LEVER ON / OFF SWITCH DISCHARGE CHUTE PRIMER LIGHT FUEL SHUT-OFF VALVE RECOIL (AUXILIARY) STARTER HANDLE HANDLE KNOB CLEAN-OUT TOOL MUFFLER NOTE: ITEMS ABOVE ARE SHOWN IN THEIR TYPICAL LOCATION ON THE ENGINE.
OPERATION The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your snow thrower or performing any adjustments or repairs. We recommend standard safety glasses or a wide vision safety mask worn over spectacles. TO CONTROL SNOW DISCHARGE (See Fig.
OPERATION TO MOVE FORWARD AND BACKWARD (See Fig. 16) SELF-PROPELLING, forward and reverse movement of the snow thrower, is controlled by the traction drive control lever located on the left side handle. • Squeeze traction drive control lever to handle to engage the drive system. • Release traction drive control lever to stop the forward or reverse movement of the snow thrower. SPEED and DIRECTION are controlled by the drive speed control lever.
OPERATION • If snow thrower must be operated over gravel surface, use extra caution and be sure skid plates are adjusted to lowest (highest scraper clearance) position. 1. Shut off engine and wait for all moving parts to stop. 2. Adjust skid plates by loosening the hex nuts, then moving skid plate to desired position. Be sure both plates are adjusted evenly. Tighten securely.
OPERATION 8. Disconnect the power cord from the receptacle first, then from the engine. Allow the engine to warm up for a few minutes. Engine will not develop full power until it has reached normal operating temperature. WARM START - ELECTRIC STARTER Follow the steps above, keeping the choke control in the “OFF” position. COLD START - RECOIL STARTER 1. Insert safety ignition key (tied to recoil start cord) into ignition slot until it clicks. DO NOT turn the key.
MAINTENANCE GENERAL RECOMMENDATIONS LUBRICATION CHART The warranty on this snow thrower does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain snow thrower as instructed in this manual. Some adjustments will need to be made periodically to properly maintain your snow thrower. At least once a season, check to see if you should make any of the adjustments described in the Service and Adjustments section of this manual.
MAINTENANCE BELTS Check belts for deterioration and wear after every 50 hours of operation and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear. (See “TO REMOVE BELT COVER” in the Service and Adjustments section of this manual). The belts on your snow thrower are of special construction and should be replaced by original equipment manufacturer (OEM) belts available from your nearest dealer.
SERVICE AND ADJUSTMENTS 1. Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop. 2. Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug. 3. Align holes in impeller hub with holes in impeller shaft and install two (2) new 1/4-20 x 1-5/8" capscrew/shear bolts. Install 1/4-20 locknuts and tighten securely.
SERVICE AND ADJUSTMENTS TO REPLACE BELTS (See Fig. 21) The auger and traction drive belts are not adjustable. If the belts are damaged or begin to slip from wear, they should be replaced. It is recommended that the belt(s) be replaced by a Sears service center/department. NOTE: It is recommended that both the auger and traction drive belt be replaced at the same time.
SERVICE AND ADJUSTMENTS TO REMOVE WHEELS (See Fig. 22) • Remove the wheel pin and retainer pin and remove wheel from axle. IMPORTANT: When installing wheel, be sure to use the inner most hole in axle and the wheel hub hole. To disengage drive system from the wheels (for pushing or transporting the snow thrower) remove wheel pin and retainer pin from wheel hub and insert wheel pin and retainer into the outer hole in axle only.
STORAGE • Empty the fuel tank by starting the engine and letting it run until the fuel lines and carburetor are empty. • Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur. • Use fresh fuel next season. NOTE: Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container.
TROUBLESHOOTING See appropriate section in manual unless directed to an authorized service center/department. PROBLEM Does not start CAUSE 1. Fuel shut-off valve (if so equipped) in OFF position. 2. Safety ignition key is not inserted. 3. Out of fuel. 4. ON/OFF switch is OFF. 5. Choke in OFF position. 6. Primer not depressed. 7. Engine is flooded. 8. Spark plug wire is disconnected. 9. Bad spark plug. 10. Stale fuel. 11. Water in fuel. CORRECTION 1. Turn fuel shut-off valve to OPEN position. 2.
&RQVXPHU :KHHOHG 3URGXFWV ± /LPLWHG :DUUDQW\ +XVTYDUQD ZDUUDQWV WR WKH RULJLQDO UHWDLO SXUFKDVHU WKDW WKLV +XVTYDUQD SURGXFW LV IUHH IURP GHIHFWV LQ PDWHULDO RU ZRUNPDQVKLS XQGHU QRUPDO XVH DQG PDLQWHQDQFH IURP WKH GDWH RI UHWDLO SXUFKDVH IRU WKH DSSOLFDEOH :DUUDQW\ 3HULRG VKRZQ RQ ([KLELW $ &HUWDLQ FRPSRQHQWV H J HQJLQHV DQG WUDQVPLVVLRQV DUH H[FOXGHG IURP FRYHUDJH DQG RWKHU OLPLWDWLRQV DSSO\ DV GHVFULEHG LQ WKLV GRFXPHQW +XVTYDUQD ZLOO UHSDLU RU UHSODFH DW LWV GLVFUHWLRQ DQ\ GHIHFWLYH SURG
F 3UHYHQWDWLYH PDLQWHQDQFH DV RXWOLQHG LQ WKH RSHUDWRU¶V PDQXDO ,Q DGGLWLRQ \RX PXVW FHDVH XVLQJ WKH SURGXFW LPPHGLDWHO\ XSRQ DQ\ IDLOXUH RU GDPDJH 7KH SURGXFW VKRXOG EH WDNHQ WR DQ DXWKRUL]HG +XVTYDUQD VHUYLFLQJ GHDOHU SULRU WR DQ\ IXUWKHU XVH 'DPDJHV UHVXOWLQJ IURP QRUPDO DJLQJ ZHDU DQG WHDU RU QHJOHFW DUH 127 FRYHUHG 7KH /LPLWHG :DUUDQW\ GRHV QRW FRYHU GDPDJH RWKHU WKDQ WKDW UHVXOWLQJ IURP GHIHFWV LQ PDWHULDO RU ZRUNPDQVKLS 7KH IROORZLQJ DUH 127 FRQVL
&RQVXPHU :KHHOHG :DUUDQW\ &KDUW ([KLELW $ &RQVXPHU SHUVRQDO KRXVHKROG XVH RQO\ 3URGXFW &RPSRQHQW 5LGLQJ /DZQ 7UDFWRUV )UDPH &KDVVLV )URQW $[OH (QJLQH 7UDQVPLVVLRQ LI PDGH E\ +XVTYDUQD 3HHUOHVV 7UDQVPLVVLRQ LI WKLUG SDUW\ %DWWHU\ 2WKHU 1RQ ([SHQGDEOH &RPSRQHQWV 5HVLGHQWLDO =HUR 7XUQ 0RZHUV 5= 2QO\ (QJLQH 7UDQVPLVVLRQ %DWWHU\ 2WKHU 1RQ ([SHQGDEOH &RPSRQHQWV 5HVLGHQWLDO =HUR 7XUQ 0RZHUV 0= (= (QJLQH 7UDQVPLVVLRQ %DWWHU\ 2WKHU 1RQ ([SHQGDEOH &RPSRQHQWV /( (GJHU (QJLQH
&RQVXPHU :KHHOHG :DUUDQW\ &KDUW ([KLELW $ &RQVXPHU SHUVRQDO KRXVHKROG XVH RQO\ &RPPHUFLDO DQ\ FRPPHUFLDO 5HQWDO DQ\ UHQWDO SURIHVVLRQDO LQVWLWXWLRQDO XVDJH DULJFXOXWUDO RU LQFRPH SURGXFLQJ XVH RWKHU WKDQ 5HQWDO 8VH 3URGXFW &RPSRQHQW )URQW 0RXQWHG 'HFN 5LGHUV (QJLQH 7UDQVPLVVLRQ
SERVICE NOTES 25
SERVICE NOTES 26
SERVICE NOTES 27
06/15/2011 SR