Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine. The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty. Esta máquina puede utilizar gasolina con un contenido de hasta el 10% de etanol (E10). El uso de una gasolina que supere el 10% de etanol (E10) anulará la garantía del producto. the product warranty.
SAFETY RULES Safe Operation Practices for Ride-On Mowers DANGER: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. • • WARNING: In order to prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug.
SAFETY RULES Safe Operation Practices for Ride-On Mowers III. SLOPE OPERATION V. SERVICE SAFE HANDLING OF GASOLINE WARNING! When loading or unloading this machine, do not exceed the maximum recommended operation angle of 15°. To avoid personal injury or property damage, use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive. • Extinguish all cigarettes, cigars, pipes, and other sources of ignition. • Use only approved gasoline container.
PRODUCT SPECIFICATIONS Gasoline Capacity and type: 4.0 Gallons/15,14 L Regular Unleaded Oil Type: (API: SJ-SN) SAE10W30 (above 32°F/0°C) SAE 5W30 (below 32°F/0°C) Oil Capacity: 64 Oz./1,89 L Spark Plug: XC12YC (Gap: .030"/0,76 mm) CONGRATULATIONS on your purchase of a new tractor. It has been designed, engineered and manufactured to give you the best possible dependability and performance.
UNASSEMBLED PARTS Keys Key(s) Slope Sheet Battery (1) Oil Drain Tube (2) Hex Bolts (1) Quick Connect (2) Nut Keps Seat (3) Bolt (1) Knob (1) Seat (1) Cup Washer (3) Flat Washer *Installed by Dealer *Brush Guard Kit ASSEMBLY Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely.
ASSEMBLY CONNECT BATTERY (See Fig. 1) WARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from accidental grounding.
ASSEMBLY ✓CHECKLIST NOTE: You may now roll your tractor off the skid. Continue using the instructions that follow to remove the tractor from the skid. WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Ensure tractor is in a well-ventilated area. Ensure the area in front of tractor is clear of other people and objects.
OPERATION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning.
OPERATION KNOW YOUR TRACTOR READ THIS MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference. D H P Z G E B F A C J K L M Fig. 4 Our tractors conform to the applicable safety standards of the American National Standards Institute. (A) ATTACHMENT LIFT LEVER - Used to raise and lower the mower or other attachments mounted to your tractor.
OPERATION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend standard safety glasses or a wide vision safety mask worn over spectacles. HOW TO USE YOUR TRACTOR ENGINE • Move throttle control (D) between half and full speed (fast) position.
OPERATION TO MOVE FORWARD AND BACKWARD (See Fig. 8) The cutting height range is approximately 1 to 4" (25,4 to 101,6 mm). The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed. The direction and speed of movement is controlled by the forward and reverse drive pedals. • Start tractor and release parking brake.
OPERATION TO STOP MOWER BLADES TO OPERATE ON HILLS Disengage attachment clutch control. CAUTION: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope. CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector chute in place (See Fig. 11). • • • • • • Choose the slowest speed before starting up or down hills. Avoid stopping or changing speed on hills.
OPERATION BEFORE STARTING THE ENGINE 4. Drive tractor to be refueled. 5. After refueling, return valve to primary position. CHECK ENGINE OIL LEVEL TO START ENGINE (See Fig. 4) The engine in your tractor has been shipped from the factory already filled with summer weight oil. • Check engine oil with tractor on level ground. • Pull up and remove oil fill cap/dipstick; wipe oil off. Reinsert the dipstick into the tube and push down firmly into place. Remove and read oil level.
OPERATION 4. Depress forward drive pedal to full forward position, hold for five (5) seconds and release pedal. Depress reverse drive pedal to full reverse position, hold for five (5) seconds and release pedal. Repeat this procedure three (3) times. 5. Shut- off engine and set parking brake. 6. Engage transmission by placing freewheel control in engaged position. (See “TO TRANSPORT” in this section of manual.) 7. Sitting in the tractor seat, start engine.
MAINTENANCE MAINTENANCE SCHEDULE BEFORE EACH USE EVERY 8 HOURS EVERY 25 HOURS EVERY 50 HOURS EVERY 100 HOURS EVERY SEASON BEFORE STORAGE Check Brake Operation Check Tire Pressure T R A C T O R Check Operator Presence and ROS Systems Check for Loose Fasteners Check/Replace Mower Blades 3 Lubrication Chart Check Battery Level 4 Clean Battery and Terminals Clean Debris off Steering Plate 5 Check Transaxle Cooling Check Mower Levelness Check V-Belts Check Engine Oil Level Change Engine Oil (mode
MAINTENANCE TRACTOR BLADE CARE For best results mower blades must be kept sharp. Replace bent or damaged blades. Always observe safety rules when per form ing any maintenance. BRAKE OPERATION If tractor requires more than five (5) feet (1,5 m) to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted. (See “TO CHECK BRAKE” in the Service and Adjustments section of this manual.
MAINTENANCE V-BELTS OIL DRAIN VALVE Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear. CLOSED AND LOCKED POSITION TRANSAXLE MAINTENANCE The transmission fan and cooling fins should be kept clean to ensure proper cooling. Do not attempt to clean fan or transmission while engine is running or while the transmission is hot.
MAINTENANCE CLEANING AIR FILTER Your engine will not run properly using a dirty air filter. Service air cleaner more often under dusty conditions. • • CLEAN AIR SCREEN The air screen is over the air intake blower located on top of engine. The air screen must be kept free of dirt and chaff to prevent engine damage from overheating. Clean with a wire brush or compressed air to remove dirt and stubborn dried gum fibers. Clean engine, battery, seat, finish, etc. of all foreign matter.
MAINTENANCE DECK WASHOUT PORT (See Fig. 23) Your tractor’s deck is equipped with a washout port as part of its deck wash system. It should be utilized after each use. 1. Drive the tractor to a level, clear spot on your lawn, near enough to a water spigot for your garden hose to reach. IMPORTANT: Make certain the tractor’s discharge chute is directed AWAY from your house, garage, parked cars, etc. Remove bagger chute or mulch cover if attached. 2.
SERVICE AND ADJUSTMENTS WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: • Depress brake pedal fully and set parking brake. • Place attachment clutch in “DISENGAGED” position. • Turn ignition key to “STOP” and remove key. • Ensure the blades and all moving parts have completely stopped. • Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. TO REMOVE MOWER (See Fig. 24) • • • • • • TO INSTALL MOWER (See Fig.
SERVICE AND ADJUSTMENTS • • From right side of mower, first insert 90° end of anti-sway bar (S) into hole in transaxle bracket (T), located near left rear tire in front of transaxle. NOTE: Flashlight may be helpful. ANTI-SWAY BAR (S) LOCATION • ATTACH REAR LIFT LINKS (C) - Lift rear corner of mower and position slot in link assembly over pin on rear mower bracket (D) and secure with washer and retainer spring. Repeat on opposite side of tractor.
SERVICE AND ADJUSTMENTS TO LEVEL MOWER FRONT-TO-BACK ADJUSTMENT (See Figs. 34 & 35) IMPORTANT: Deck must be level side-to-side. Ensure tires are properly inflated to the PSI shown on tires. If tires are over or under inflated, it may affect the appearance of your lawn and lead you to think the mower is not adjusted properly.
SERVICE AND ADJUSTMENTS TO CHECK BRAKE MOWER DRIVE BELT INSTALLATION (See Fig. 37 & 38) NOTE: For ease in installing the deck belt, refer to the routing decal on the cutting deck. If tractor requires more than five (5) feet (1,5 m) to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced. You may also check brake by: 1. Park tractor on a level, dry concrete or paved surface, depress brake pedal all the way down and engage parking brake. 2.
SERVICE AND ADJUSTMENTS TO REMOVE WHEEL (See Fig. 40) TO REPLACE MOTION DRIVE BELT (See Fig. 39) • • Block up axle securely. Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose). • Repair tire and reassemble. • On rear wheels only: align grooves in rear wheel hub and axle. Insert square key. • Replace washers and snap retaining ring securely in axle groove. • Replace axle cover.
SERVICE AND ADJUSTMENTS • • Reconnect harness to LED light. Close hood. INTERLOCKS AND RELAYS WEAK OR DEAD BATTERY Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting. • Check wiring. FULLY CHARGED BATTERY TO REPLACE FUSE Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash. Fig. 41 REPLACING BATTERY (See Fig. 42) TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig.
STORAGE ENGINE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. FUEL SYSTEM IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS DURING STORAGE.
TROUBLESHOOTING PROBLEM Will not start CAUSE CORRECTION 1. Out of fuel. 1. Fill fuel tank. 2. 3. 4. 5. 6. 2. 3. 4. 5. 6. 7. Loose or damaged wiring. 8. Engine valves out of adjustment. Wait several minutes before attempting to start. Replace spark plug. Clean/replace air filter. Replace fuel filter. Empty fuel tank and carburetor, refill tank with fresh gasoline and replace fuel filter. 7. Check all wiring. 8. Contact an authorized service center/department. Hard to start 1. 2. 3. 4. 5. 6. 7.
TROUBLESHOOTING PROBLEM CAUSE CORRECTION Engine continues to run when operator leaves seat with attachment clutch engaged 1. Faulty operator-safety presence control system. Poor cut - uneven 1. 2. 3. 4. 5. Worn, bent or loose blade. Mower deck not level. Buildup of grass, leaves, trash under mower. Bent blade mandrel. Clogged mower deck vent holes from buildup of grass, leaves, and trash around mandrels. 1. 2. 3. 4. 5. Replace blade. Tighten blade bolt. Level mower deck.
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION FOL DA L O NG D THIS O I T S T A E D LIN 1 5 DEG E RE E S LOP E ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL 15 DEGREES MAX. WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than 15 degrees. Make turns gradually to prevent tipping or loss of control. Exercise extreme caution when changing direction on slopes. 1. Fold this page along dotted line indicated above. 2.
REGLAS DE SEGURIDAD Prácticas de Operación Seguras para las Segadoras Conducibles PELIGRO: ESTA MAQUINA CORTADORA ES CAPAZ DE AMPUTAR LAS MANOS Y LOS PIES Y DE LANZAR OBJETOS. SI NO SE OBSERVAN LAS INSTRUCCIONES DE SEGURIDAD SIGUIENTES SE PUEDEN PRODUCIR LESIONES GRAVES O LA MUERTE.
REGLAS DE SEGURIDAD • Prácticas de Operación Seguras para las Segadoras Conducibles V. SERVICIO Mantener la máquina libre de hierba, hojas u otros escombros que pueden tocar el tubo de escape / partes del motor calientes y quemarse. No permitir que el puente del cortacésped cargue hojas u otros residuos que pueden causar acumulaciones. Limpiar toda salpicadura de aceite o carburante antes de hacer operaciones sobre la máquina o guardarla. Dejarla enfriar antes de guardarla.
ESPECIFICACIONES DEL PRODUCTO Capacidad y Tipo de Gasolina: 15,14 L / 4.0 Galones Regular Sin Plomo Tipo de Aceite (API: SJ-SN): SAE10W30 (sobre 32°F/0°C) SAE 5W30 (deabajo 32°F/0°C) Capacidad de Aceite: 64 Oz./1,89 L Bujía: XC12YC (Abertura: 0,76 mm / .030 ") Sistema de Carga: 15 Amps @ 3600 RPM Batería: Amp/Hr: Min. CCA: Modelo Tamaño: Torsión del Perno de la Cuchilla: FELICITACIONES por la compra de su tractor.
PIEZAS SIN MONTAR Llaves Hoja de pendiente Batería (1) Tubo de desagüe (2) Perno (1) Accesorio Llave(s) del conexión (2) Tuerca Asiento (3) Perno (1) Manilla (1) Asiento (1) Arandela de la cazoleta (3) Arandela *Instalado por el distribuidor *Juego de cubierta MONTAJE Su tractor nuevo ha sido montado en la fábrica con la excepción de aquellas partes que no se han montado por razones de envío.
MONTAJE CONEXIÓN DE LA BATERÍA (Vea Fig. 1) ADVERTENCIA: No haga cortocircuito con los terminales de la batería al permitir que una llave de tuerca o cualquier otro objeto entre en contacto con ambos terminales a la misma vez. Antes de instalar la batería remueva las pulseras de metal, los relojes de pulsera de metal, los anillos, etc. El terminal positivo tiene que conectarse primero para evitar las chispas debido a la conexión a tierra por accidente.
MONTAJE AVISO: Ahora puede sacar el tractor de la tarima. Continúe usando las instrucciones que siguen para retirar el tractor de la tarima. ✓LISTA DE REVISIÓN ADVERTENCIA: Antes de empezar, leer, entender y seguir todas las instrucciones presentes en la sección Operaciones de este manual. Asegurarse que el tractor esté en un área bien ventilada. Asegurarse que la zona delante del tractor esté libre de otras personas y objetos.
OPERACIÓN Estos símbolos pueden aparecer sobre su tractor o en la literatura proporcionada con el producto. Aprenda y comprenda sus significados.
OPERACIÓN FAMILIARICESE CON SU TRACTOR LEA ESTE MANUAL Y LAS REGLAS DE SEGURIDAD ANTES DE OPERAR SU TRACTOR Compare las ilustraciones con su tractor para familiarizarse con las ubicaciones de los diversos controles y ajustes. Guarde este manual para referencia en el futuro. D H P Z G E B F A C J K L M Fig. 4 Nuestros tractores cumplen con los estándares de seguridad del American National Standard Institute. (H) INTERRUPTOR DE LUCES - Enciende y apaga las luces delanteras.
OPERACIÓN La operación de cualquier tractor puede hacer que salten objetos extraños dentro de sus ojos, lo que puede producir daños graves en éstos. Siempre use anteojos de seguridad o protecciones para los ojos mientras opere su tractor o cuando haga ajustes o reparaciones. Recomendamos gafas de seguridad o una máscara de visión amplia de seguridad usada sobre las gafas. COMO USAR SU TRACTOR MOTOR • PARA AJUSTAR EL FRENO DE ESTACIONAMIENTO (Vea Fig.
OPERACIÓN MOVERSE HACIA ADELANTE Y HACIA ATRÁS (Vea Fig. 8) La gama de la altura de corte es de aproximadamente 25,4 a 101,6 mm (1 a 4 pulgadas). Las alturas se miden desde el suelo a la punta de la cuchilla cuando el motor no está funcionando. Estas alturas son aproximadas y pueden variar dependiendo de las condiciones del suelo, de la altura del césped y del tipo del césped que se está segando. La dirección y la velocidad de movimientos están controlados por los pedales de marcha adelante y atrás.
OPERACIÓN PARA PARAR LAS CUCHILLAS DE LA SEGADORA • PARA OPERAR EN CERROS Desenganche el control del embrague del accesorio. ADVERTENCIA: No maneje hacia arriba o hacia abajo en cerros con pendientes superiores a 15° y no maneje atravesando ninguna pendiente. Utilice la guía de la pendiente proporcionada en la parte posteriora de este manual.
OPERACIÓN ANTES DE HACER ARRANCAR EL MOTOR PARA OPERAR DE LA VALVULA DE GASOLINA DE RESERVA (Vea Fig. 14) El motor de su tractor se envía de fábrica ya lleno con aceite de peso para verano. 1. REVISE EL NIVEL DE ACEITE DEL MOTOR • Revise el aceite del motor con el tractor en terreno nivelado. • Levante y quite la varilla indicadora de nivel de relleno del aceite; limpie el aceite. Reinserte la varilla en el tubo y empújela hacia abajo firmemente en su lugar. Remueva y lea el nivel del aceite.
OPERACIÓN CONSEJOS PARA SEGAR PURGAR LA TRANSMISIÓN • PRECAUCIÓN: Nunca enganche o desenganche la palanca del control de rueda libre cuando el motor esta funcionando. • Para asegurar la operación y ejecución adecuada, es recomendado que la transmisión sea purgada antes de operar el tractor para la primera vez. Este proceso removerá cualquier aire adentro de la transmisión que se halla formado durante el transporte de su tractor.
MANTENIMENTO PROGRAMA DE MANTENIMIENTO ANTES DE CADA USO CADA 8 HORAS CADA 25 HORAS CADA 50 HORAS CADA 100 HORAS CADA TEMPORADA ALMACENAMIENTO Revisar la operación del freno Revisar la presión de las llantas T R A C T O R Verificar la sistemas presencia del operador y sistemas "ROS" Revisar si hay sujetadores sueltos Afilar/cambiar las cuchillas de la segadora 3 Tabla de lubricación Revisar el nivel de bateria 4 Limpiar la batería y los tereminales Limpie los residuos de la placa de dirección.
MANTENIMENTO TRACTOR PRECAUCIÓN: Usar solamente la hojas de repuesto aprobada por el fabricante de su cortacésped. Usar una hoja no aprobada por el fabricante de su cortacésped es peligroso, puede dañar su cortacésped y anular su garantía. Siempre observe las reglas de seguridad cuando dé mantenimiento.
MANTENIMENTO CORREAS "V" CUBIERTA DEL TABLERO INFERIOR Revise las correas "V" para verificar si existe deterioro y desgaste después de 100 horas de operación y cámbielas si es necesario. Las correas no son ajustables. Cambie las correas si empiezan a deslizarse debido al desgaste. SUJETADOR ENFRIAMIENTO DEL TRANSEJE Las aletas de enfriamiento y el ventilador de la transmisión tienen que mantenerse limpios para asegurar el enfriamiento adecuado.
MANTENIMENTO FILTRO DEL AIRE LIMPIEZA Su motor puede sufrir averías y funcionar de manera incorrecta con un filtro del aire sucio. Déle servicio al filtro de aire más a menudo si se usa en condiciones polvorosas. Vea la manual de la motor. • • LIMPIEZA DE LA PANTALLA DE AIRE La pantalla de aire está sobre el soplador de la toma de aire que se ubica en la parte superior del motor. La pantalla de aire se debe mantener libre de suciedad y paja para evitar que el motor se dañe por sobrecalentamiento.
MANTENIMENTO PUERTO DE LAVADO DE LA CUBIERTA (Vea Fig. 23) La plataforma del tractor está equipada con un puerto de lavado como parte del sistema de lavado de la plataforma. Se debe utilizar después de cada uso. 1. Lleve el tractor a un lugar horizontal y despejado de su césped, lo bastante cerca de una boca de riego como para que llegue la manguera del jardín. IMPORTANTE: Asegúrese de que la boca de descarga del tractor está orientada LEJOS de su casa, garaje, coches aparcados, etc.
SERVICIO Y AJUSTES ADVERTENCIA: PARA EVITAR LESIÓNES SERIAS, ANTES DE DAR CUALQUIER SERVICIO O DE HACER AJUSTES: • Presione el pedal de freno completamente y aplique el freno de estacionamiento. • Ponga el embrague del accesorio en la posición desenganchado (DISENGAGED). • Ponga la llave de ignición en la posición de apagado (STOP) y remuévala. • Asegúrese que las cuchillas y que todas las partes movibles se hayan detenido completamente.
SERVICIO Y AJUSTES • • Desde el lado derecho de la cortadora de césped, inserte primero el extremo en 90° de la barra antibalanceo (S) dentro del agujero de la escuadra de transeje (T), ubicado cerca de la rueda trasera izquierda adelante del transeje. NOTA: Puede resultar útil usar una linterna.
SERVICIO Y AJUSTES PARA NIVELAR LA SEGADORA AJUSTE DE DELANTE A ATRÁS (Vea Fig. 34 y 35) Asegúrese de que los neumáticos estén inflados a la PSI que se indica en estos. Si están demasiado inflados o poco inflados, el césped no le quedará bien cortado, lo cual podrá llevarlo a pensar que la segadora no está bien regulada. IMPORTANTE: El piso debe quedar bien nivelado de lado a lado.
SERVICIO Y AJUSTES CONTROLAR Y AJUSTAR EL FRENO INSTALACIÓN DE LA CORREA DE TRANSMISIÓN DEL CORTACÉSPED (consulte las imágenes 37 y 38) TENGA EN CUENTA: Para facilitar la instalación de la cinta de la plataforma, consulte la etiqueta sobre la ruta que está en la plataforma de corte. • Asegúrese de que el resorte del equipo esté instalado al brazo auxiliar y al perno de anillo. • Coloque la correa en todas las poleas excepto la polea izquierda del mandril.
SERVICIO Y AJUSTES PARA REMOVER LAS RUEDAS PARA HACER REPARACIONES (Vea Fig. 40) PARA CAMBIAR LA CORREA DE IMPULSIÓN DE MOVIMIENTO (Vea Fig. 39) Estacione el tractor en una superficie nivelada. Ponga el freno de mano. Si necesita asistencia, del lado de abajo del apoyapiés izquierdo hay una guía práctica para el montaje de la correa • • Bloquee el eje en forma segura.
SERVICIO Y AJUSTES • • Vuelva a conectar el cableado al faro LED. Cierre el capó. ENTRECIERRE Y RELÉ El alambrado suelto o dañado puede producir el mal funcionamiento de su tractor, o que deje de funcionar, o le impida el arrancar. • Revise el alambrado. 02614 BATERÍA DÉBIL O DESCARGADA BATERÍA COMPLETAMENTE CARGADA PARA CAMBIAR EL FUSIBLE Cámbielo por un fusible tipo enchufable de 30 amps, tipo automotriz. El sujetador del fusible está ubicado detrás del tablero. Fig.
ALMACENAMIENTO MOTOR Inmediatamente prepare su tractor para el almacenamiento al final de la temporada o si el tractor no se va a usar por 30 días o más.
IDENTIFICACIÓN DE PROBLEMAS PROBLEMA No arranca CAUSA CORRECCIÓN 1. 2. 3. 4. 5. 6. Sin combustible. Motor ahogado. Bujía mala. Filtro de aire sucio. Filtro de combustible sucio. Agua en el combustible. 1. 2. 3. 4. 5. 6. 7. 8. Alambrado suelto o dañado. Válvulas del motor desajustadas. 7. 8. 1. 2. 3. 4. 5. Filtro de aire sucio. Bujía mala. Batería baja o descargada. Filtro de combustible sucio. Combustible rancio o sucio. 1. 2. 3. 4. 5. 6. 7. Alambrado suelto o dañado.
IDENTIFICACIÓN DE PROBLEMAS PROBLEMA CAUSA El motor continúa funcionando cuando el operador se baja del asiento con el embrague del accesorio enganchado 1. El corte disparejo 1. 2. 3. Mala descarga del césped 1. Revise el alambrado, los interruptores y la conexiones.Si no están correctas, pongase en contacto con un centro de servicio cualificado. PRECAUCIÓN: NO opere la máquina sino hasta haber corregido el problema. Cuchilla desgastada, doblada o suelta. El conjunto segador no estánivelado.
GUÍA SUGERIDA PARA MEDIR LAS PENDIENTES CON LA VISTA PARA UNA OPERACIÓN SEGURA PL E G AR A LO EST L A RGO A ES DE U N L A A PEN LÍNE DIE A P N U T NTE E DE ADA 1 5 GRA DOS SOLAMENTE ANDE CUESTA ARRIBA O CUESTA ABAJO Y NO ATRAVIESE EL CERRO 15 GRADOS MAX. ADVERTENCIA: Para evitar daños graves, haga funcionar su tractor arriba y abajo de las pendientes, nunca transversalmente con respecto a las pendientes. No cortar pendientes mayores de 15 grados.
NOTES/AVISO 58
NOTES/AVISO 59
12.03.18 CL Printed in U.S.A.