Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine. The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty. Esta máquina puede utilizar gasolina con un contenido de hasta el 10% de etanol (E10). El uso de una gasolina que supere el 10% de etanol (E10) anulará la garantía del producto.
SAFETY RULES Safe Operation Practices for Ride-On Mowers DANGER: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. • WARNING: In order to prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug. • Before and while backing, look behind and down for small children.
SAFETY RULES Safe Operation Practices for Ride-On Mowers III. SLOPE OPERATION • • • • WARNING! When loading or unloading this machine, do not exceed the maximum recommended operation angle of 15°. • Slopes are a major factor related to loss of control and tip-over accidents, which can result in severe injury or death. Operation on all slopes requires extreme caution. If you cannot back up the slope or if you feel uneasy on it, do not mow it. • Mow up and down slopes, not across.
PRODUCT SPECIFICATIONS Gasoline Capacity and type: 3 Gallons (11,35 L) Unleaded Regular Oil Type: (API: SJ-SN) SAE 30 (above 32°F/0°C) SAE 5W30 (below 32°F/0°C) Oil Capacity: w/Filter: w/o Filter: Spark Plug: Champion XC12YC Gap: .030"(0,76 mm) Spark Plug Torque: 180 lb-in (20 Nm) Charging System: 16 Amps @3600 RPM Battery: Amp/Hr: Min. CCA: Case Size: Blade Bolt Torque: CONGRATULATIONS on your purchase of a new tractor.
UNASSEMBLED PARTS Keys Slope Sheet Battery (1) Oil Drain Tube (2) Hex Bolts Key(s) (1) Quick Connect (2) Nut Keps ASSEMBLY Your new tractor has been assembled at the factory with the exception of those parts left unassembled for shipping purposes. TOOLS REQUIRED FOR ASSEMBLY • First connect RED battery cable to positive (+) terminal with bolt and nut as shown. Tighten securely. Slide terminal cover over terminal. • Connect BLACK grounding cable to negative (-) terminal with remaining bolt and nut.
ASSEMBLY ✓CHECKLIST NOTE: You may now roll your tractor off the skid. Continue using the instructions that follow to remove the tractor from the skid. WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Ensure tractor is in a well-ventilated area. Ensure the area in front of tractor is clear of other people and objects.
OPERATION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning.
OPERATION KNOW YOUR TRACTOR READ THIS OPERATOR'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference. G H P E D B F A C J K L M Fig. 3 Our tractors conform to the applicable safety standards of the American National Standards Institute. (H) LIGHT SWITCH - Turns the headlights on and off.
OPERATION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend standard safety glasses or a wide vision safety mask worn over spectacles. ENGINE • Move throttle control (D) to slow position.
OPERATION TO USE CRUISE CONTROL (J) (See Fig. 7) TO ADJUST GAUGE WHEELS (See Fig. 9) The cruise control feature can be used for forward travel only. Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions. NOTE: Adjust gauge wheels with tractor on a flat level surface.
OPERATION REVERSE OPERATION SYSTEM (ROS) (See Fig. 11) TO TRANSPORT (See Fig. 3 &12) When pushing or towing your tractor, ensure transmission is disengaged by placing freewheel control in freewheeling position. Free wheel control is located at the rear drawbar of tractor. • Raise attachment lift to highest position with attachment lift control. • Pull freewheel control out and into the slot and release so it is held in the disengaged position.
OPERATION BEFORE STARTING THE ENGINE TO START ENGINE (See Fig. 3) CHECK ENGINE OIL LEVEL The Briggs & Stratton Endurance engine equipped with your tractor features a Ready-Start automatic choke system to provide simplified starting in normal conditions. Please read the following starting instruction carefully. The engine in your tractor has been shipped from the factory already filled with summer weight oil. • Check engine oil with tractor on level ground.
OPERATION MOWING TIPS PURGE TRANSMISSION • CAUTION: Never engage or disengage freewheel lever while the engine is running. • To ensure proper operation and performance, it is recommended that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have developed during shipping of your tractor.
MAINTENANCE MAINTENANCE SCHEDULE BEFORE EACH USE EVERY 8 HOURS EVERY 25 HOURS EVERY 50 HOURS EVERY 100 HOURS EVERY SEASON BEFORE STORAGE Check Brake Operation Check Tire Pressure T R A C T O R Check Operator Presence and ROS Systems Check for Loose Fasteners Check/Replace Mower Blades 3 Lubrication Chart Check Battery Level 4 Clean Battery and Terminals Clean Debris off Steering Plate 5 Check Transaxle Cooling Check Mower Levelness Check V-Belts Check Engine Oil Level Change Engine Oil (mode
MAINTENANCE TRACTOR BLADE CARE Always observe safety rules when per form ing any maintenance. For best results mower blades must be kept sharp. Replace bent or damaged blades. BRAKE OPERATION If tractor requires more than five (5) feet (1,5 m) to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted. (See “TO CHECK BRAKE” in the Service and Adjustments section of this manual.
MAINTENANCE TO CHANGE ENGINE OIL (See Fig. 16 - 18) V-BELTS Determine temperature range expected before oil change. All oil must meet API service classification SJ-SN. • Be sure tractor is on level surface. • Oil will drain more freely when warm. • Catch oil in a suitable container. Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear.
MAINTENANCE CLEANING ENGINE OIL FILTER • Replace the engine oil filter every season or every other oil change if the tractor is used more than 100 hours in one year. NOTE: If needed, remove lower dash covers using steps from "Lower dash cover removal" section of this manual. • AIR FILTER Clean engine, battery, seat, finish, etc. of all foreign matter. Clean debris from steering plate. Debris can restrict clutch/brake pedal shaft movement, causing belt slip and loss of drive. See Fig. 20.
MAINTENANCE DECK WASHOUT PORT (See Fig. 21) Your tractor’s deck is equipped with a washout port as part of its deck wash system. It should be utilized after each use. 1. Drive the tractor to a level, clear spot on your lawn, near enough to a water spigot for your garden hose to reach. IMPORTANT: Make certain the tractor’s discharge chute is directed AWAY from your house, garage, parked cars, etc. Remove bagger chute or mulch cover if attached. 2.
SERVICE AND ADJUSTMENTS WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: • Depress brake pedal fully and set parking brake. • Place attachment clutch in “DISENGAGED” position. • Turn ignition key to “STOP” and remove key. • Make sure the blades and all moving parts have completely stopped. • Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. TO REMOVE MOWER (See Fig.
SERVICE AND ADJUSTMENTS • • ATTACH MOWER SIDE SUSPENSION ARMS (A) TO CHASSIS - Position hole in arm over pin (B) on outside of tractor chassis and secure with retainer spring. Repeat on opposite side of tractor. • Insert end of link (E) into hole in front mower bracket and secure with washer and retainer spring (J). E A J F H B Fig. 25 • Fig.
SERVICE AND ADJUSTMENTS TO LEVEL MOWER FRONT-TO-BACK ADJUSTMENT (See Figs. 30 & 31) IMPORTANT: Deck must be level side-to-side. Ensure tires are properly inflated to the PSI shown on tires. If tires are over or under inflated, it may affect the appearance of your lawn and lead you to think the mower is not adjusted properly.
SERVICE AND ADJUSTMENTS TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 32) BELT REMOVAL • Remove mower. (See “TO REMOVE MOWER” section in this manual.) The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake. NOTE: Observe entire motion drive belt and position of all belt guides and keepers. BELT REMOVAL • Remove mower from tractor (See “TO REMOVE MOWER” in this section of manual). • Work belt off both mandrel pulleys and idler pulleys.
SERVICE AND ADJUSTMENTS TO REMOVE WHEEL (See Fig. 34) TO REMOVE CABLES, REVERSE ORDER • BLACK cable first from chassis and then from the fully charged battery. • RED cable last from both batteries. • • Block up axle securely. Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose). • Repair tire and reassemble. • On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.
SERVICE AND ADJUSTMENTS TRANSMISSION TO REPLACE HEADLIGHT BULB • • • • Raise hood. Pull bulb holder out of the hole in the backside of the grill. Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill. Close hood. REMOVAL/REPLACEMENT Should your transmission require removal for service or replacement, it should be purged after reinstallation and before operating the tractor. See “PURGE TRANSMISSION” in the Operation section of this manual.
STORAGE ENGINE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. FUEL SYSTEM IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS DURING STORAGE.
TROUBLESHOOTING PROBLEM CAUSE 1. 2. 3. 4. 5. 6. CORRECTION 7. Loose or damaged wiring. 8. Engine valves out of adjustment. Fill fuel tank. Wait several minutes before attempting to start. Replace spark plug. Clean/replace air filter. Replace fuel filter. Empty fuel tank and carburetor, refill tank with fresh gasoline and replace fuel filter. 7. Check all wiring. 8. Contact an authorized service center/department. Hard to start 1. 2. 3. 4. 5. 6. 7. Dirty air filter. Bad spark plug.
TROUBLESHOOTING PROBLEM CAUSE CORRECTION Engine continues to run when operator leaves seat with attachment clutch engaged 1. Faulty operator-safety presence control system. Poor cut - uneven 1. 2. 3. 4. 5. Worn, bent or loose blade. Mower deck not level. Buildup of grass, leaves, trash under mower. Bent blade mandrel. Clogged mower deck vent holes from buildup of grass, leaves, and trash around mandrels. 1. 2. 3. 4. 5. Replace blade. Tighten blade bolt. Level mower deck.
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION FOL D AL ONG THIS DOT IS A TED 15 D LINE EGR EE S LOP E 28 ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL 15 DEGREES MAX. WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than 15 degrees. Make turns gradually to prevent tipping or loss of control. Exercise extreme caution when changing direction on slopes. 1. Fold this page along dotted line indicated above. 2.
02.05.20 CL Printed in U.S.A.