User Manual
Table Of Contents
- Symbols
- Contents
- Note the following before starting:
- Dear Customer,
- Important
- Personal protective equipment
- Machine¢s safety equipment
- Cutting equipment
- Fitting the main body
- Assembling the handlebar and throttle
- Connecting throttle cable and stop switch wires
- Fitting blades and trimmer heads
- Fitting the transport guard
- Adjusting the harness and brush cutter
- Fuel safety
- Fuel
- Fueling
- Check before starting
- Starting and stopping
- General working instructions
- Carburettor
- Air filter
- Fuel filter
- Bevel gear
- Spark plug
- Maintenance schedule
- Technical data
- EC Declaration of Conformity
- Símbolos
- Índice
- Antes de arrancar, observe lo siguiente:
- Apreciado cliente:
- Importante
- Equipo de protección personal
- Equipo de seguridad de la máquina
- Equipo de corte
- Montaje del cuerpo principal
- Montaje del manillar y la empuñadura de acelerador
- Conexión del cable de acelerador y los hilos del interruptor de parada
- Montaje de la hoja y del cabezal de corte
- Montaje de la protección para transportes
- Ajuste del arnés y la desbrozadora
- Seguridad en el uso del combustible
- Carburante
- Repostaje
- Control antes de arrancar
- Arranque y parada
- Instrucciones generales de trabajo
- Carburador
- Filtro de aire
- Filtro de combustible
- Engranaje angulado
- Bujía
- Programa de mantenimiento
- Datos técnicos
- Declaración CE de conformidad
- Símbolos
- Índice
- Antes de arrancar, observe o seguinte:
- Prezado cliente!
- Importante
- Equipamento de protecção pessoal
- Equipamento de segurança da máquina
- Equipamento de corte
- Montagem da carcaça principal
- Montagem da direcção e do punho do acelerador
- Ligação do cabo do acelerador e dos fios do interruptor de paragem
- Montagem da lâmina e cabeçote de recorte
- Montagem da protecção para transporte
- Ajuste do suporte e do roçador
- Segurança no manejo de combustível
- Combustível
- Abastecimento
- Controlo antes de arrancar
- Arranque e paragem
- Instruções gerais de trabalho
- Carburador
- Filtro de ar
- Filtro de combustível
- Engrenagem angular
- Vela de ignição
- Esquema de manutenção
- Especificações técnicas
- Certificado CE de conformidade
![](/manual/husqvarna/9666573-01/user-manual-english-spanish-indonesian-portuguese/images/img-13.png)
ASSEMBLY
English – 13
8 Plug the stop switch wires (H) into the matching
connectors from the engine. Note that wire polarity is
not important.
9 Lap and fix the stop switch wires and connectors with
clamp (I).
10 Fit the dust cover (J).
11 Refit the air filter cover.
Fitting blades and trimmer heads
Fitting the guard extension
CAUTION! The guard extension shall always be fitted
when using the trimmer head/plastic blades and
combination guard. The guard extension shall always be
removed when using the grass blade and combination
guard.
Hook the blade guard/combination guard (A) onto the
fitting on the shaft and secure with the bolt.
Enter the guard extension guide in the slot of the
combination guard. Then click the guard extension into
position on the guard with the four quick-fasteners.
H
J
I
!
WARNING!
When fitting the cutting attachment it is
extremely important that the raised
section on the drive disc/support flange
engages correctly in the centre hole of
the cutting attachment. If the cutting
attachment is fitted incorrectly it can
result in serious and/or fatal personal
injury.
!
WARNING! Never use a cutting
attachment without an approved guard.
See the chapter on Technical data. If an
incorrect or faulty guard is fitted this can
cause serious personal injury.
IMPORTANT! If a saw blade or grass blade are to be
used the machine must be equipped with the correct
handlebar, blade guard and harness.