User Manual
Table Of Contents
- Symbols
- Contents
- Note the following before starting:
- Dear Customer,
- Important
- Personal protective equipment
- Machine¢s safety equipment
- Cutting equipment
- Fitting the main body
- Assembling the handlebar and throttle
- Connecting throttle cable and stop switch wires
- Fitting blades and trimmer heads
- Fitting the transport guard
- Adjusting the harness and brush cutter
- Fuel safety
- Fuel
- Fueling
- Check before starting
- Starting and stopping
- General working instructions
- Carburettor
- Air filter
- Fuel filter
- Bevel gear
- Spark plug
- Maintenance schedule
- Technical data
- EC Declaration of Conformity
- Símbolos
- Índice
- Antes de arrancar, observe lo siguiente:
- Apreciado cliente:
- Importante
- Equipo de protección personal
- Equipo de seguridad de la máquina
- Equipo de corte
- Montaje del cuerpo principal
- Montaje del manillar y la empuñadura de acelerador
- Conexión del cable de acelerador y los hilos del interruptor de parada
- Montaje de la hoja y del cabezal de corte
- Montaje de la protección para transportes
- Ajuste del arnés y la desbrozadora
- Seguridad en el uso del combustible
- Carburante
- Repostaje
- Control antes de arrancar
- Arranque y parada
- Instrucciones generales de trabajo
- Carburador
- Filtro de aire
- Filtro de combustible
- Engranaje angulado
- Bujía
- Programa de mantenimiento
- Datos técnicos
- Declaración CE de conformidad
- Símbolos
- Índice
- Antes de arrancar, observe o seguinte:
- Prezado cliente!
- Importante
- Equipamento de protecção pessoal
- Equipamento de segurança da máquina
- Equipamento de corte
- Montagem da carcaça principal
- Montagem da direcção e do punho do acelerador
- Ligação do cabo do acelerador e dos fios do interruptor de paragem
- Montagem da lâmina e cabeçote de recorte
- Montagem da protecção para transporte
- Ajuste do suporte e do roçador
- Segurança no manejo de combustível
- Combustível
- Abastecimento
- Controlo antes de arrancar
- Arranque e paragem
- Instruções gerais de trabalho
- Carburador
- Filtro de ar
- Filtro de combustível
- Engrenagem angular
- Vela de ignição
- Esquema de manutenção
- Especificações técnicas
- Certificado CE de conformidade
STARTING AND STOPPING
20 – English
Choke: Set the choke control in the choke position.
Hold the body of the machine on the ground using your
left hand (CAUTION! Not with your foot!). Grip the starter
handle, slowly pull out the cord with your right hand until
you feel some resistance (the starter pawls grip), now
quickly and powerfully pull the cord.
Never twist the
starter cord around your hand.
Repeat pulling the start handle until the engine starts.
When the engine starts, return choke control to run
position and apply full throttle; the throttle will
automatically disengage from the start setting.
CAUTION! Do not pull the starter cord all the way out and
do not let go of the starter handle when the cord is fully
extended. This can damage the machine.
CAUTION! Do not put any part of your body in marked
area. Contact can result in burns to the skin, or electrical
shock if the spark plug cap has been damaged. Always
use gloves. Do not use a machine with damaged spark
plug cap.
For throttle handles with a start throttle
lock:
Set the throttle to the start position by first pressing the
throttle lockout and the throttle trigger, then pressing the
start throttle button (A). Then release the throttle lockout
and the throttle trigger, followed by the start throttle
button. The throttle function is now activated. To return the
engine to idle, press the throttle lockout and throttle
trigger again.
Stopping
Stop the engine by switching off the ignition.
!
WARNING! When the engine is started
with the choke in either the choke or
start throttle positions the cutting
attachment will start to rotate
immediately.