User Manual
Table Of Contents
- Symbols
- Contents
- Note the following before starting:
- Dear Customer,
- Important
- Personal protective equipment
- Machine¢s safety equipment
- Cutting equipment
- Fitting the main body
- Assembling the handlebar and throttle
- Connecting throttle cable and stop switch wires
- Fitting blades and trimmer heads
- Fitting the transport guard
- Adjusting the harness and brush cutter
- Fuel safety
- Fuel
- Fueling
- Check before starting
- Starting and stopping
- General working instructions
- Carburettor
- Air filter
- Fuel filter
- Bevel gear
- Spark plug
- Maintenance schedule
- Technical data
- EC Declaration of Conformity
- Símbolos
- Índice
- Antes de arrancar, observe lo siguiente:
- Apreciado cliente:
- Importante
- Equipo de protección personal
- Equipo de seguridad de la máquina
- Equipo de corte
- Montaje del cuerpo principal
- Montaje del manillar y la empuñadura de acelerador
- Conexión del cable de acelerador y los hilos del interruptor de parada
- Montaje de la hoja y del cabezal de corte
- Montaje de la protección para transportes
- Ajuste del arnés y la desbrozadora
- Seguridad en el uso del combustible
- Carburante
- Repostaje
- Control antes de arrancar
- Arranque y parada
- Instrucciones generales de trabajo
- Carburador
- Filtro de aire
- Filtro de combustible
- Engranaje angulado
- Bujía
- Programa de mantenimiento
- Datos técnicos
- Declaración CE de conformidad
- Símbolos
- Índice
- Antes de arrancar, observe o seguinte:
- Prezado cliente!
- Importante
- Equipamento de protecção pessoal
- Equipamento de segurança da máquina
- Equipamento de corte
- Montagem da carcaça principal
- Montagem da direcção e do punho do acelerador
- Ligação do cabo do acelerador e dos fios do interruptor de paragem
- Montagem da lâmina e cabeçote de recorte
- Montagem da protecção para transporte
- Ajuste do suporte e do roçador
- Segurança no manejo de combustível
- Combustível
- Abastecimento
- Controlo antes de arrancar
- Arranque e paragem
- Instruções gerais de trabalho
- Carburador
- Filtro de ar
- Filtro de combustível
- Engrenagem angular
- Vela de ignição
- Esquema de manutenção
- Especificações técnicas
- Certificado CE de conformidade
MAINTENANCE
26 – English
When the engine runs short of fuel supply, check the fuel
cap and the fuel filter for blockage.
Bevel gear
The bevel gear is filled with the right quantity of grease at
the factory. However, before using the machine you
should check that the bevel gear is filled three-quarters
full with grease. Use HUSQVARNA special grease.
The grease in the bevel gear does not normally need to
be changed except if repairs are carried out.
Spark plug
The spark plug condition is influenced by:
• Incorrect carburettor adjustment.
• An incorrect fuel mixture (too much or incorrect type
of oil).
• A dirty air filter.
These factors cause deposits on the spark plug
electrodes, which may result in operating problems and
starting difficulties.
If the machine is low on power, difficult to start or runs
poorly at idle speed: always check the spark plug first
before taking any further action. If the spark plug is dirty,
clean it and check that the electrode gap is 0,6-0,7 mm.
The spark plug should be replaced after about a month in
operation or earlier if necessary.
CAUTION! Always use the recommended spark plug
type! Use of the wrong spark plug can damage the piston/
cylinder. Check that the spark plug is fitted with a
suppressor.